JTB00518NAS2
Service Bulletin Details
Public Details for: JTB00518NAS2
Situation: an engine coolant leak may be evident from the engine coolant expansion tank filler neck. This may be accompanied by steam from under the hood and/or an engine overheat message displayed on the instrument cluster.
Models from 2017
2017 JAGUAR F-PACE |
2017 JAGUAR XE |
2017 JAGUAR XF |
Models from 2016
2016 JAGUAR XF |
Page 1 of 5 TECHNICAL BULLETIN JTB00518NAS2 14 NOV 2016 © Jaguar Land Rover North America, LLC NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle. This reissue replaces all previous versions. Please destroy all previous versions. Changes are highlighted in gray SECTION: 303-03 Engine Coolant Expansion Tank Leak AFFECTED VEHICLE RANGE: XE (X760) Model Year: VIN: Assembly Plant: F-PACE (X761) Model Year: VIN: Assembly Plant: XF (X260) Model Year: VIN: Assembly Plant: XE (X760) Model Year: VIN: Assembly Plant: 2017 921222-970403 Solihull 2017 100002-093015 Solihull 2016-2017 Y00001-Y43893 Castle Bromwich 2017 P00001-P05263 Castle Bromwich MARKETS: NAS CONDITION SUMMARY: Situation: An engine coolant leak may be evident from the engine coolant expansion tank filler neck. This may be accompanied by steam from under the hood and/or an engine overheat message displayed on the Instrument Cluster. Cause: This may be caused by a distorted engine coolant expansion tank filler neck. Action: Should a Customer express concern, follow the Service Instruction below. PARTS: T2H4044 Engine coolant expansion tank 1 C2P17700 Coolant Pressure Cap (140kPa) 1 C2P20325 Coolant Pressure Cap (200kPa) 1 JLM209722 Engine Coolant 1 TOOLS: http://topix.jaguar.jlrext.com/topix/service/document/710422 11/15/2016 Page 2 of 5 Refer to Workshop Manual for any required special tools. WARRANTY: NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time. NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero. DESCRIPTION SRO TIME (HOURS) CONDITION CODE CAUSAL PART Engine coolant expansion tank - Check 26.15.05 0.1 13 T2H4044 Expansion tank - Renew 26.15.01 0.2 13 T2H4044 NOTE: Normal Warranty procedures apply. SERVICE INSTRUCTION: WARNING: Cover the engine coolant expansion tank pressure cap with a thick cloth to prevent the possibility of scalding. Release the cooling system pressure by slowly turning the engine coolant expansion tank cap a quarter of a turn. Failure to follow this instruction may result in personal injury. CAUTION: The engine cooling system must be maintained with the correct concentration and type of antifreeze solution to prevent corrosion and frost damage. Failure to follow this instruction may result in damage to the engine. CAUTION: Engine coolant will damage the paint finished surfaces. If spilt, immediately remove the coolant and clean the area with water. CAUTION: Never remove the engine coolant expansion tank cap under any circumstances while the engine is operating. Failure to follow this instruction may result in damage to the engine. CAUTION: Since injury such as scalding could be caused by escaping steam or coolant, make sure the vehicle cooling system is cool prior to carrying out this procedure. CAUTION: Be prepared to collect escaping coolant. 1. Remove the engine coolant expansion tank pressure cap. 2. Set a vernier caliper to 50.70mm. http://topix.jaguar.jlrext.com/topix/service/document/710422 11/15/2016 Page 3 of 5 3. Check the dimensions of the engine coolant expansion tank threaded neck in the two positions shown. • If the dimensions across the centerline neck are less than 50.70mm, go to Step 5. • If the dimensions across the centerline of the neck are 50.70mm or greater, go to Step 4. http://topix.jaguar.jlrext.com/topix/service/document/710422 11/15/2016 Page 4 of 5 4. Visually inspect the sealing bead on the engine coolant expansion tank neck to check for damage. • If the sealing bead is damaged, go to Step 5. • If no damage is found: • Install a new engine coolant expansion tank pressure cap. • Top up the engine coolant to the MAX level mark. • Run the engine up to normal operating temperature, allowing the electric cooling fan to operate at least once without problem before releasing the vehicle. • Switch the engine OFF. http://topix.jaguar.jlrext.com/topix/service/document/710422 11/15/2016 Page 5 of 5 5. Install a new engine coolant expansion tank and a new coolant pressure cap (see TOPIx Workshop Manual section 303-03: Engine Cooling - Engine Coolant Expansion Tank). 6. Run the engine up to normal operating temperature, allowing the electric cooling fan to operate at least once without problem before releasing the vehicle. 7. If engine coolant loss continues and/or an engine overheat message is displayed on the Instrument Cluster following completion of this Technical Bulletin, further diagnosis and repair will be necessary (see TOPIx Workshop Manual section 303-03: Engine Cooling - Cooling System Draining, Filling and Bleeding). To be performed as a separate claim. http://topix.jaguar.jlrext.com/topix/service/document/710422 11/15/2016