L-SB-0019-15
Service Bulletin Details
Public Details for: L-SB-0019-15
Lsb: some 2011 - 2013 model year ct 200h vehicles may exhibit a mil "on" condition with diagnostic trouble code (dtc) P0A0F (engine failed to start), caused by purge vsv/pcv line separation from the throttle body housing. One or more of the
Models from 2013
2013 LEXUS CT 200H |
2013 LEXUS CT HYBRID |
Models from 2012
2012 LEXUS CT 200H |
2012 LEXUS CT HYBRID |
Models from 2011
2011 LEXUS CT 200H |
2011 LEXUS CT HYBRID |
L-SB-0019-15 June 26, 2015 MIL "ON" DTC P0A0F, P3190, P3191, P0171 Due to Purge VSV Vacuum Line Separation Service Category Engine/Hybrid System Section Engine Control Market USA Applicability YEAR(S) MODEL(S) 2011 – 2013 CT200H ADDITIONAL INFORMATION Introduction Some 2011 – 2013 model year CT 200h vehicles may exhibit a MIL “ON” condition with Diagnostic Trouble Code (DTC) P0A0F (Engine Failed to Start), caused by Purge VSV/PCV line separation from the throttle body housing. One or more of the following DTCs may also set: • P3190 (Poor Engine Power) • P3191 (Engine Does Not Start) • P0171 (System Too Lean [Bank One]) Replace the Purge VSV (Vacuum Switching Valve Assembly) and reprogram the Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) with the latest calibration to address this condition. Production Change Information This bulletin applies to vehicles produced BEFORE the Production Change Effective VIN shown below. MODEL PLANT PRODUCTION CHANGE EFFECTIVE VIN CT 200h Kyushu JTHKD5BH#D2158591 Calibration Information CALIBRATION ID ENGINE 2ZR-FXE PREVIOUS NEW 37601000 37601100 37601200 © 2015 Lexus, a division of Toyota Motor Sales, USA Page 1 of 5 June 26, 2015 L-SB-0019-15 Page 2 of 5 MIL "ON" DTC P0A0F, P3190, P3191, P0171 Due to Purge VSV Vacuum Line Separation Warranty Information OP CODE DESCRIPTION TIME OFP EG1506 Replace Purge VSV and Reprogram ECM (PCM) Engine 0.8 89660-76010 89660-76011 T1 T2 8C 74 APPLICABLE WARRANTY • This repair is covered under the Lexus Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle’s in-service date. • Warranty application is limited to occurrence of the specified condition described in this bulletin. Parts Information PART NUMBER PART NAME QTY Computer, Engine Control (ECM/PCM) – 25860-37020 Valve Assy, Vacuum Switching 1 00451-00001-LBL Authorized Modification Labels 1 PREVIOUS NEW 89660-76010 89660-76011 89660-76012 NOTE • The ECM (PCM) should NOT be replaced as part of the Repair Procedure. • Authorized Modification Labels may be ordered in packages of 25 from the Materials Distribution Center (MDC) through Dealer Daily – Dealer Support Materials Orders. Required Tools & Equipment SPECIAL SERVICE TOOLS (SST) PART NUMBER QTY GR8 Battery Diagnostic Station* 00002-MCGR8 1 NOTE Additional SSTs may be ordered by calling 1-800-933-8335. © 2015 Lexus, a division of Toyota Motor Sales, USA L-SB-0019-15 June 26, 2015 Page 3 of 5 MIL "ON" DTC P0A0F, P3190, P3191, P0171 Due to Purge VSV Vacuum Line Separation Required Tools & Equipment (Continued) REQUIRED EQUIPMENT Techstream 2.0* Techstream Lite SUPPLIER ADE PART NUMBER QTY TS2UNIT TSLITEPDLR01 1 NOTE • Only ONE of the Techstream units listed above is required. • Software version 10.10.018 or later is required. • Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. • The Diagnostic Tester is NOT recommended for flash reprogramming. Please use Techstream or an approved J2534 interface to perform flash reprogramming updates. Visit techinfo.toyota.com for more information regarding J2534 reprogramming. * Essential SST. Repair Procedure 1. Inspect for proper installation of the PCV hose and Purge VSV vacuum line at the throttle body. Ensure the vacuum line is secured at the Purge VSV. If all lines are properly seated, this bulletin does NOT apply. Follow normal diagnostic procedures per the Repair Manual. Reinstall and secure any unseated lines, replace the Purge VSV, then proceed to step 2. Refer to the Technical Information System (TIS), applicable model and model year Repair Manual: • 2011 CT 200h: Engine/Hybrid System – Emission Control – “2ZR-FXE Emission Control: Purge Valve: Removal / Installation” • 2012 CT 200h: Engine/Hybrid System – Emission Control – “2ZR-FXE Emission Control: Purge Valve: Removal / Installation” • 2013 CT 200h: Engine/Hybrid System – Emission Control – “2ZR-FXE Emission Control: Purge Valve: Removal / Installation” © 2015 Lexus, a division of Toyota Motor Sales, USA L-SB-0019-15 June 26, 2015 Page 4 of 5 MIL "ON" DTC P0A0F, P3190, P3191, P0171 Due to Purge VSV Vacuum Line Separation Repair Procedure (Continued) 2. Check for the Authorized Modifications Label affixed to the vehicle in the location shown in Figure 1. Confirm if the ECM (PCM) calibration has been updated. If the calibration ID listed is NOT the latest ECM (PCM) calibration — go to step 3. Figure 1. Location of Authorized Modifications Label on 2011 – 2013 CT 200h 1 Replacement ECM (PCM) Part Number (i.e., 89660-76012) 2 New Calibration ID(s) (i.e., 37601200) 3 Dealer Code 4 Date Completed 5 This SB Number © 2015 Lexus, a division of Toyota Motor Sales, USA L-SB-0019-15 June 26, 2015 Page 5 of 5 MIL "ON" DTC P0A0F, P3190, P3191, P0171 Due to Purge VSV Vacuum Line Separation Repair Procedure (Continued) 3. Flash reprogram the ECM (PCM). NOTE • The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain battery voltage at 13.5 volts while flash reprogramming the vehicle. • For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8 Instruction Manual located on the Technical Information System (TIS), Diagnostics – Tools & Equipment – Battery Diagnostics. Follow the procedures outlined in Service Bulletin No. L-SB-0021-14, “Techstream ECU Flash Reprogramming Procedure,” and flash reprogram the ECM (PCM) with the NEW calibration file update. 4. Install the Authorized Modifications Label. A. Using a permanent marker, enter the following information on the label: • ECM part number [Refer to the Parts Information section for the NEW PART NUMBER] • Calibration ID(s) [Refer to the Calibration Information section for the NEW CALIBRATION ID] • Dealer Code • Repair Date • Change Authority [This bulletin number] B. Affix the Authorized Modifications Label to the vehicle at the location shown in Figure 1. The Authorized Modifications Label is available through the MDC, P/N 00451-00001-LBL. 5. Test drive the vehicle to confirm proper vehicle operation. © 2015 Lexus, a division of Toyota Motor Sales, USA