PI 0854

Mack Trucks, Inc.
Greensboro, NC USA
Service Program
Trucks
This service program replaces program PI0854 dated 10.2014.
Date
Group
No.
Release
Page
2.2015
284
054
03
1(7)
Software Updates
MP7, MP8, MP10 US2014
CHU, CXU, GU, LEU, MRU, TD
PI0854, Control Module Software Updates
(February 2015)
Information
Software updates with enhancements are available for the aftertreatment control module
(ACM), engine control module (ECM), vehicle ECU (VECU) and instrument cluster (IC) for
MACK MP7, MP8 and MP10 engines with US2014 emission level on vehicles built from
January 2, 2014 to September 28, 2014. Software updates address the following.
•
•
•
•
•
•
•
•
Exhaust Temperature Plausibility Faults (P2080 / P2084 / P242B)
P2463 High Soot Load
P0402 EGR Mass Flow High
P0401 EGR Mass Flow Low
Fuel Pressure Low Fault P008A
Incorrect Urea Heating Valve, Temperature Targets
Engine Hours Missing In Instrument Cluster
P055B Calibration Revisions to Piston Cooling Jet Diagnostic
Note: Control modules are required to be programmed in the following order:
•
•
•
•
ACM
ECM
VECU
IC
Required Tools
Premium Tech Tool version 2.03.41 or higher
Vocom Diagnostic Connector 88890304
Communication Interface 88890300
Note: Using other interfaces may affect programming speed.
Note: Check Premium Tech Tool version by clicking on Help tab and then click on “About
Tech Tool”.
PV729-PI0854
USA69519
Mack Trucks, Inc.
Service Program
Date
2.2015
Group
No.
Release
284
054
03
Procedure
DANGER
Do not attempt to repair or service this vehicle without having sufficient training, the correct
service literature and the proper tools. Failure to follow this could make the vehicle unsafe
and lead to serious personal injury or death.
1 Verify service program eligibility by checking service program status in VDA.
2 Secure the vehicle for service by parking it on a flat level surface, applying the parking
brake, chocking the rear wheels, and placing the transmission in neutral.
3 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 16 pin
OBD cable 88890304 and Communication Interface 88890300. Connect the PC to a
functional LAN or modem connection and a 120 Volt AC source.
4 Turn the ignition switch “ON”.
5 Log in to PTT and Identify Vehicle is displayed.
Page
2(7)
Mack Trucks, Inc.
Service Program
Date
2.2015
Group
No.
Release
284
054
03
6 Once the vehicle has been identified, enter the Work Order Number information, then click
Start Work.
W2079940
7 From the Main Menu select Program and then Program Electronic Control Unit 1700-0803-39. Then click Start.
W2079941
Page
3(7)
Mack Trucks, Inc.
Service Program
Date
2.2015
Group
No.
Release
284
054
03
8 Select ACM.
W2079943
9 Select Program to update the ACM with the latest software.
W2085461
Page
4(7)
Mack Trucks, Inc.
Service Program
Date
2.2015
Group
No.
Release
284
054
03
10 Certain conditions must be met to continue with programming: battery voltage above 10v,
parking brake applied, and ignition key in ON position with engine not running. When all
conditions have been met, click Continue to proceed with programming.
W2080113
11 Select “I accept” to agree to the terms and press continue to proceed.
Note: In the United States and Canada, the programing is NOT chargeable. An invoice will
not be generated.
W2085462
Page
5(7)
Mack Trucks, Inc.
Service Program
Date
2.2015
Group
No.
Release
284
054
03
12 If the software is already updated, this screen opens. Select Yes to reload existing
software.
W2094387
13 When programming is complete, click Exit to return to Main Menu to program the next
control unit.
14 After ACM programing is complete, update the ECM, VECU and IC.
15 When all programing is complete, clear any diagnostic trouble codes (DTC) and Finish
Work.
Page
6(7)
Mack Trucks, Inc.
Service Program
Date
2.2015
Group
No.
Release
284
054
03
Reimbursement
This repair is covered by an authorized Service
Program. Reimbursement is obtained via the
normal claim handling process.
UCHP
Reimbursement
eWarranty
Reimbursement
Claim Type (used only when uploading from the
Dealer Bus. Sys.)
41
41
Recall Status
Vehicle inspected, repair not required
1- Inspected
OK
Vehicle repaired per instruction
2- Modified
per instruction
Labor Code
Primary Labor Code
2841–22–09–02
0.9 hrs
2306N-01-96
0.9 hrs.
Time to take charge and determine campaign status
1700–16–01–01
0.3 hrs
101AA–0A–00
0.3 hrs
Causal Part
3092091
3092091
Parts Disposition
N/A
N/A
SCC Code
S6646
N/A
Authorization Number
N/A
PI0854
Expiration Date
31 - May - 2015
31 - May 2015
Note: Take Charge Time is not included in the Labor Code for this operation. Take charge
may be eligible but can only be used once per repair visit. If vehicle is having other warranty
repairs performed, take charge should be charged to the warranty repair, otherwise take
charge can be charged to this service program.
Page
7(7)