NTB17-070
Service Bulletin Details
Public Details for: NTB17-070
Voluntary service campaign 2004-2011 titan, and 2005-2011 frontier and xterra; air bag diagnosis sensor unit introduction nissan is conducting a voluntary service campaign on certain specific model year 2004- 2011 titan, and 2005-2011 f
- 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 -
Models from 2011
2011 NISSAN FRONTIER |
2011 NISSAN TITAN |
2011 NISSAN XTERRA |
Models from 2010
2010 NISSAN FRONTIER |
2010 NISSAN TITAN |
2010 NISSAN XTERRA |
Models from 2009
2009 NISSAN FRONTIER |
2009 NISSAN TITAN |
2009 NISSAN XTERRA |
Models from 2008
2008 NISSAN FRONTIER |
2008 NISSAN TITAN |
2008 NISSAN XTERRA |
Models from 2007
2007 NISSAN FRONTIER |
2007 NISSAN TITAN |
2007 NISSAN XTERRA |
Models from 2006
2006 NISSAN FRONTIER |
2006 NISSAN TITAN |
2006 NISSAN XTERRA |
Models from 2005
2005 NISSAN FRONTIER |
2005 NISSAN TITAN |
2005 NISSAN XTERRA |
Models from 2004
2004 NISSAN TITAN |
Reference: Date: NTB17-070 June 22, 2017 VOLUNTARY SERVICE CAMPAIGN 2004-2011 TITAN, AND 2005-2011 FRONTIER AND XTERRA; AIR BAG DIAGNOSIS SENSOR UNIT P7318 CAMPAIGN ID #: APPLIED VEHICLES: 2004-2011 Titan (A60) 2005-2011 Frontier (D40) 2005-2011 Xterra (N50) Check Service COMM to confirm campaign eligibility. INTRODUCTION Nissan is conducting a voluntary service campaign on certain specific model year 20042011 Titan, and 2005-2011 Frontier and Xterra vehicles to reprogram the air bag diagnosis sensor unit. This repair will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P7318 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer’s inventory. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/8 REQUIRED SPECIAL TOOL J-51594 (SRS Reprogramming Cable) This disc, supplied with the cable, is not needed for this bulletin’s procedure Figure 1 NOTE: One J-51594 SRS reprogramming cable (J-51594 cable) has been supplied to each dealer. Additional J-51594 cables can be obtained from Tech-Mate at 1-800662-2001. SERVICE PROCEDURE IMPORTANT: Before starting, make sure: ASIST on the CONSULT PC has been freshly synchronized (updated to the current date). All C-III plus software updates (if any) have been installed. NOTE: The CONSULT PC automatically gets applicable reprogramming data during ASIST synchronization. Make sure the driver for the J-51594 cable is installed/updated: a. Connect the CONSULT PC to the Internet. b. Connect the J-51594 cable to the CONSULT PC USB port. c. Wait one (1) minute, the drivers will install / update automatically. NOTE: Steps a-c above are only required one time to install the driver into the CONSULT PC. But it is recommended that steps a-c above be performed at the beginning of each day to confirm the latest software has been installed. 2/8 NTB17-070 Reprogramming Procedure NOTE: The screen shots in this bulletin are similar to, if not the same as, those on your CONSULT PC. 1. At this time, do not turn the ignition ON. 2. Connect the J-51594 cable to the vehicle’s DLC connector and the PC USB port. Make sure the J-51594 cable is securely connected at both ends. CAUTION: Make sure the J-51594 cable is securly connected. If the J-51594 cable connection is loose during reprogramming, the process will be interrupted and the air bag diagnosis sensor unit may be damaged. 3. Connect the AC Adapter to the CONSULT PC. CAUTION: Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the air bag diagnosis sensor unit may be damaged. 4. Connect the GR-8 battery charger to the vehicle battery and select ECM Power Supply Mode. CAUTION: Be sure the battery charger is connected securely to the battery. Make sure the battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery voltage goes out of this range during reprogramming, the air bag diagnosis sensor unit may be damaged. 5. Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc. IMPORTANT: Make sure to turn OFF all vehicle electrical loads. Make sure the battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery voltage goes out of this range during reprogramming, the air bag diagnosis sensor unit may be damaged. 3/8 NTB17-070 6. Turn ON the CONSULT PC, and then locate the Acu Repro icon on the CONSULT PC screen. 7. Select (double-click) “ACU”. xxx Step 7: Double-click “ACU” Figure 2 NOTE: If the icon shown in Figure 2 does not display, navigate ASIST to Specialty Tools, and then select P7318 ACU Reprogram (see Figure 3). The icon in Figure 2 should then display. Specialty Tools P7318 ACU Reprogram Figure 3 4/8 NTB17-070 8. When the window in Figure 4 displays, select Start Repro. Step 8 Figure 4 9. Turn the ignition ON, and then select OK. Step 9 Figure 5 5/8 NTB17-070 10. After selecting OK, the screen in Figure 6 will appear. While this screen displays, the air bag diagnosis sensor unit is being reprogrammed. OK OK F63C D FA6EDRv OK Write EEPDATA Figure 6 11. When reprogramming completes, the screen in Figure 7 appears. 12. Turn the ignition OFF, and then select OK. Please press OK after you turn off IGN. Step 12: Turn ignition off first Figure 7 6/8 NTB17-070 13. The countdown screen in Figure 8 will appear after selecting OK in step 12. 14. After OK has been selected, wait until the countdown completes (about 10 seconds). Please wait for 8 sec. Figure 8 15. After the countdown completes, the screen in Figure 9 displays. 16. Turn the ignition ON. 17. Select OK. Please turn on IGN. Step 16 Step 17 Figure 9 18. When the screen in Figure 10 displays, reprogramming is complete. 19. Select OK. CAUTION: DO NOT disconnect the J-51594 cable until the screen in Figure 10 displays and OK is selected. XXX Reprogramming completion. Step 19 Figure 10 7/8 NTB17-070 20. Close C-III plus. 21. Turn the ignition OFF. 22. Disconnect the J-51594 cable from the vehicle and CONSULT PC. 23. Disconnect the GR-8 from the vehicle. 24. Turn the ignition from OFF to ON and observe the air bag warning light: This light should illuminate for seven (7) seconds, and then go out. NOTE: If the air bag warning light does not operate as described above, there may be an issue not covered by this campaign. Refer to ASIST and the ESM for additional diagnostic and repair information. CLAIMS INFORMATION Submit a Campaign (CM) line claim using the following claims coding: CAMPAIGN (CM) ID # DESCRIPTION VEHICLE OP CODE FRT Titan P7318 Reprogram Air Bag Diagnosis Sensor Unit Frontier P73180 0.3 hrs. Xterra 8/8 NTB17-070