V011417 2014077

Technical Bulletin
Model(s)
Year
Eng. Code
Trans. Code
VIN Range From
VIN Range To
All
2006-2007
2.0L
All
All
All
(BPY)
Condition
01 14 17 July 30, 2014 2014077 Supersedes T. B. V011101 dated January 24, 2011 to remove reference to
Update 24M2 and include SVM unit code.
Update Programming to Eliminate DTC P0601 Stored in DTC Memory
Note:
Discard CD Literature Number W4220LTFSIP0601.
This Technical Bulletin addresses the following Diagnostic Trouble Code (DTC) on all 2006 - 2007 vehicles
equipped with a 2.0L TFSI engine.
DTC
P0601
Description
Internal Control Module Memory Check Sum Error
Technical Background
Engine Control Modules Affected Part No.
1K0907115B
3C0907115P
1K0907115H
1Q0907115B
3C0907115G
1Q0907115D
3C0907115F
Page 1 of 6 plus attachment
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Production Solution
A change to ECM software was completed in the factories as of November 2006
Service
Note:
BEFORE performing this update:
Inform the customer that, after the update, the gear display feature in the MFI while in Drive “D” (e.g. 1, 2, 3, 4, 5,
6) will no longer appear. This update is not reversible and the feature cannot be turned back on.
DO NOT perform Update Programming if the customer wants to keep the gear display feature.
Code “Customer Refused Repairs” as per claiming instructions in this bulletin.
Update-Programming Procedure:
Tip:
To Update-Programming using SVM, review and follow instructions in Technical Bulletin Instance 2014603
“Software Version Management”. The SVM Process must be completed in its entirety so the database receives
the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to
support the claim.
Note:
Prior to launching the VAS-PC and ODIS service diagnostic applications and starting control module update
process, confirm tester screen saver and power settings in accordance with Special Tools and Equipment -Service
Information Circular # VVT-12-02. Failure to do so may result in the tester entering power save mode during data
transfer, and subsequent control module failure.
When using a VAS 6150/5051B or VAS 5052A tester in conjunction with a VAS 5054A wireless transmitter head
for a flash procedure, please connect a USB cable between the transmitter head and the tester. Failure to do so
may lead to errors during the flash procedure. VAS tools must only be used with their power adapters plugged in.
Under no circumstances should they be used on battery power alone during the programming procedure.
Critical Warning: The Midtronics Battery Charger must be connected to the vehicle battery for the duration of
the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the
battery drops below 12.5 volts, the programming could fail which may result in damage to the control module.
Control modules damaged by inadequate voltage will not be covered under the warranty policy. The technician
should verify the vehicle voltage prior to starting the update process, and should monitor the voltage for the
duration of the update.
Page 2 of 6 plus attachment
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
• Update the Engine Control Module using the SVM Unit code as listed in the table below:
Control Module Table
Model
Engine
Old Part No.
Old Software
Version
New Part No.
New
Software
Version (or
higher)
SVM Unit
Code
Jetta GLI,
Golf GTI
2.0T FSI
(BPY)
1K0907115B
All
1K0907115B
0040
301D
Golf GTI
2.0T FSI
(BPY)
1K0907115H
All
1K0907115H
0040
301D
EOS
2.0T FSI
(BPY)
1Q0907115B
All
1Q0907115E
0020
301D
EOS
2.0T FSI
(BPY)
1Q0907115E
All
1Q0907115E
0020
301D
EOS
2.0T FSI
(BPY)
1Q0907115D
All
1Q0907115E
0020
301D
Passat
2.0T FSI
(BPY)
3C0907115F
All
3C0907115F
0030
301D
Passat
2.0T FSI
(BPY)
3C0907115S
All
3C0907115S
0020
301D
Passat
2.0T FSI
(BPY)
09G927750FP
All
09G927750HJ
1068
301D
Passat
2.0T FSI
(BPY)
09G927750CJ
All
09G927750HJ
1068
301D
Passat
2.0T FSI
(BPY)
3C0907115P
All
3C0907115S
0020
301D
Passat
2.0T FSI
(BPY)
3C0907115G
All
3C0907115F
0030
301D
Jetta GLI
Page 3 of 6 plus attachment
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
The procedure can be found in GFF under Functions/ Component Selection, Software Version Management,
Adapting Software.
WARNING:
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may
result if contact is made with spinning fan blades.
Keep hands and all objects away from Radiator Fan(s) during Update Process!
Tip:
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried
out that is not explicitly stated in the Technical Bulletin.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM
Technical Bulletin Instance 2014603.
Page 4 of 6 plus attachment
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
1)
Procedures Manual
Model(s)
Year(s)
Eng. Code(s)
All
2006-2007
Trans. Code(s)
VIN Range From
VIN Range To
All
All
All
2.0L
(BPY)
SAGA Coding
Claim Type:
Use applicable Claim Type
1)
Damage
Service Number:
HST
Damage Location (Depends on
Service No.)
--
Use applicable when indicated
in ElsaWeb (L/R)
Code
2470
0039
Parts Manufacturer
Golf/GTI, Eos, Passat
WWO
Jetta/GLI
3ME
2)
2)
Golf GTI, Jetta GLI, Eos
Labor Operation : Charge Battery
3)
27068950 = 10 TU
3)
24702599 = 50 TU
Labor Operation : Update Programming
Passat
Labor Operation : Charge Battery
3)
27068950 = 10 TU
Labor Operation : Update Programming
3)
24702599 = 60 TU
Causal Part: Select Labor Operation
24702599
Diagnostic Time
GFF Time expenditure
4)
01500000 = 20 TU max.
YES
Page 5 of 6 plus attachment
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Road Test
01210002 = 00 TU
NO
01210004 = 00 TU
Technical Diagnosis
01320000 = 00 TU max.
NO
Claim Comment: Input “As per Technical Bulletin 2014077” in comment section of Warranty Claim.
1)
Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only
2)
Code per warranty vendor code policy.
3)
Labor Time Units (TUs) are subject to change with ELSA updates.
4)
Documentation required per Warranty Policies and Procedures Manual.
Required Parts and Tools
No Special Parts required.
Tool Description
Tool No:
Midtronics Battery Tester/Charger
InCharge 940 (INC-940)
or
GRX3000VAS
VAS Diagnostic Tool
VAS 6150/X & VAS 6160/X with:
ODIS Service with current online updates
Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.
Page 6 of 6 plus attachment
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
OWNER INFORMATION ABOUT CONTROL MODULE TUNING*
ACKNOWLEDGEMENT AND AUTHORIZATION FOR
REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S)
*) “TUNING” is described as the addition of or modification of any component which causes a
Volkswagen vehicle to perform outside the normal parameters and specifications approved by
Volkswagen Group of America / Volkswagen Group Canada.
Date:
Dealer Number:
Vehicle Identification Number:
Repair Order Number:
Dealer stamp
I
, owner or driver of the above identified Volkswagen, confirm:
- “Tuning” as described above (especially power increasing modifications) has NOT been
performed on my vehicle.
- “Tuning” as described above has been performed on my vehicle and the following components
were modified or installed:
TUNING was performed by (Please provide Company name and telephone number, if you wish us
to contact them):
I understand that if my Control Module is determined to have been tuned, any damage caused by
the tuning of the Control Module (including adverse emissions consequences) will not be covered
by VWGoA / VGC warranties.
I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by
doing so, I understand that this process will automatically overwrite (destroy) and permanently
delete any tuning program that was previously installed on the Control Module of my Volkswagen
vehicle.
By signing below, I fully acknowledge and understand that the tuning program will not be restored
and VWGoA / VGC, will not be liable in any way for the loss of tuning data.
Signature of Customer
E 2014 Volkswagen Group of America Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printi ng and is subject to the copyright and other intellectual
property rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to ma ke changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitte d in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or rep osted to other sites, without the prior expressed written permission of the publisher .