A011476 2019485-

Technical Service Bulletin
01 MIL on (DTC P2070, P2006 or P2007 stored in ECM)
01 14 76 2019485/3 April 15, 2014. Supersedes Technical Service Bulletin Group 24 number 10-22 dated June 2,
2010 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
A6
2005 - 2008
All
3.2l FSI
A4
2005 - 2008
All
3.2l FSI
A4 Cabriolet
2007 - 2008
All
3.2l FSI
Condition
REVISION HISTORY
Revision
Date
Purpose
3
-
Revised header data (Updated customer codes; added DTCs)
2
6/12/2010
Revised header data (Controlling TSB display in ElsaWeb)
1
12/3/2008
Original publication
• MIL on.
• One of the following DTCs is stored in the engine control module (ECM), J623 (address word 01):
• DTC P2070 (Intake Manifold Tuning (IMT) Valve Stuck Open).
• DTC P2006 (Intake Manifold Runner Control Stuck Closed, Bank 1).
• DTC P2007 (Intake Manifold Runner Control Stuck Closed, Bank 2).
• There may be slight power reduction at high RPMs.
This condition does not cause stalling.
Technical Background
Vacuum line cracks.
Production Solution
Updated vacuum line.
© 2014 Audi of America, Inc.
Page 1 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Service
1.
Use the vacuum pump to identify the vacuum leak
in the system. Attach vacuum pump as shown
(Figure 1).
Figure 1. Vacuum pump, attached.
2.
Apply vacuum.
3.
Identify the leaking vacuum line by separating and blocking each section.
Tip: The vacuum line (06E133633) attached to the vacuum pump (Figure 1) is usually the causal part.
4.
If a vacuum leak is identified, replace the appropriate vacuum line.
5.
If vacuum stays stable during the test procedure, check corresponding actuator diaphragm:
• DTC P2070 may be caused by a leak in the IMT actuator diaphragm.
• DTC P2006 and P2007 may be caused by a leak in the manifold runner actuator diaphragm.
© 2014 Audi of America, Inc.
Page 2 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Warranty
Claim Type:
Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin
is informational only.
Service Number:
2483
Damage Code:
0015
Labor Operations:
Identify leaking vacuum line, replace vacuum line
2483 1999
30 TU
Diagnostic Time:
GFF
0150 0000
10 TU
Road test prior to service procedure
No allowance 0 TU
Road test after service procedure
0121 0004
10 TU
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB # 2019485/3
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
NOTE: Replace only the affected vacuum line.
Part number
Part Description
Quantity
06E133633
Vacuum line
1
06E133647A
Vacuum line
1
06E133782B
Vacuum line
1
06E133778C
Vacuum line
1
Tool Number
Tool Description
VAS 6213
Vacuum pump
© 2014 Audi of America, Inc.
Page 3 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Additional Information
All parts and service references provided in this TSB (2019485) are subject to change and/or removal. Always
check with your Parts Department and service manuals for the latest information.
© 2014 Audi of America, Inc.
Page 4 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.