FSB284-064
Service Bulletin Details
Public Details for: FSB284-064
Ecm and acm reprogramming, obd2015
- 9999 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 - 2003 - 2002 - 2001 - 2000 - 1999 - 1998 - 1997 - 1996 - 1995 -
Models from 9999
9999 VOLVO VAH |
9999 VOLVO VHD |
9999 VOLVO VN |
Models from 2018
2018 VOLVO VAH |
2018 VOLVO VHD |
Models from 2017
2017 VOLVO VAH |
2017 VOLVO VHD |
Models from 2016
2016 VOLVO VAH |
2016 VOLVO VHD |
Models from 2015
2015 VOLVO VAH |
2015 VOLVO VHD |
Models from 2014
2014 VOLVO VAH |
2014 VOLVO VHD |
Models from 2013
2013 VOLVO VAH |
2013 VOLVO VHD |
Models from 2012
2012 VOLVO VAH |
2012 VOLVO VHD |
Models from 2011
2011 VOLVO VAH |
2011 VOLVO VHD |
Models from 2010
2010 VOLVO VAH |
2010 VOLVO VHD |
Models from 2009
2009 VOLVO VAH |
2009 VOLVO VHD |
Models from 2008
2008 VOLVO VAH |
2008 VOLVO VHD |
Models from 2007
2007 VOLVO VAH |
2007 VOLVO VHD |
Models from 2006
2006 VOLVO VHD |
Models from 2005
2005 VOLVO VHD |
Models from 2004
2004 VOLVO VHD |
Models from 2003
2003 VOLVO VHD |
Models from 2002
2002 VOLVO VHD |
Models from 2001
2001 VOLVO VHD |
Models from 2000
2000 VOLVO VHD |
Models from 1999
1999 VOLVO VHD |
Models from 1998
1998 VOLVO VHD |
Models from 1997
1997 VOLVO VHD |
Models from 1996
1996 VOLVO VHD |
Models from 1995
1995 VOLVO VHD |
Volvo Trucks North America Greensboro, NC USA Field Service Bulletin Trucks Date 1.2018 Group No. 284 064 Release Page 01 1(7) Engine Control Module (ECM) and Aftertreatment Control Module (ACM), Reprogramming VN, VAH, VHD FSB 284-064 Engine Control Module (ECM) and Aftertreatment Control Module (ACM), Reprogramming January 2018 Information Software updates with enhancements are available for the engine control module (ECM) and aftertreatment control module (ACM) for VOLVO D11, D13 and D16 engines on OBD2015 vehicles built from January 1, 2015 to December 31, 2015. Follow the reprogramming procedure in the following order as outlined in this document: • • USA140348062 ECM reprogramming ACM reprogramming PV729-FSB284-064_V Volvo Trucks North America Field Service Bulletin Date 1.2018 Group No. Release 284 064 01 The software updates address the following Diagnostic Trouble Codes (DTCs): • • • • • • • • • • • • • • • • • • P026C - Fuel Injector, Low Mass Flow P0507 – Idle Engine Speed Rationality: Idle Speed High P2002 – PM Filter Efficiency Monitor P0422 – Catalyst 2 Efficiency Below Threshold (Bank 1) P226D – Diesel Particulate Filter (DPF) Missing Substrate P249C – Time to Enter DEF (Diesel Exhaust Fluid) Dosing P208E – Aftertreatment Reagent Dosing Valve Clogged P2459 – To Frequent Regeneration P24A4 – DPF Restriction – Soot Accumulation Too High (Bank 1) P10FE – DPF Restriction – Soot Accumulation Moderately High (Bank 1) P226C – Boost Pressure Slow Response P249F – Excessive Time to Enter Closed Loop DPF Regeneration Control P24A0 – Closed Loop DPF Regeneration Control at Limit – Temperature Too Low P208A – Aftertreatment DEF Pump: Open Circuit P20CF – (AHI) Fuel Injector “A” Stuck Open P226C00 – Turbocharger Boost Control “A” Slow Response P205B – Aftertreatment DEF tank Temperature Sensor: Rationality Low P20128 - Engine Cooling System: Stuck Open or Leaking Thermostat Monitor Check the current main software for ECM and ACM to determine the action required as shown in the table below. Action Required ECM Main Software Action Required D11/ D13 Equal or Less Than 22741776 Update to Latest Software D16 Equal or Less Than 22644015 Update to Latest Software ACM Main Software Action Required D11/ D13 / D16 Equal or Less Than 22741796 Update to Latest Software Page 2(7) Volvo Trucks North America Field Service Bulletin Date 1.2018 Group No. Release 284 064 01 Required Tools Premium Tech Tool (PTT) version 2.06.35 or higher Vocom Diagnostic Connector 88890304 Communication Interface 88890300 Note: Using other interfaces may affect programming speed. Note: Check Premium Tech Tool version by clicking on Help tab and then click on “About Tech Tool”. Software Update Procedure You must read and understand the precautions and guidelines in Service Information, group 20, "General Safety Practices, Engines" before performing this procedure. If you are not properly trained and certified in this procedure, ask your supervisor for training before you perform it. DANGER Do not attempt to repair or service this vehicle without having sufficient training, the correct service literature and the proper tools. Failure to follow this could make the vehicle unsafe and lead to serious personal injury or death. 1 Park the vehicle on a level surface. 2 Apply the parking brake. 3 Place the transmission in neutral or park. 4 Install the wheel chocks. W7086748 5 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 16 pin OBD cable 88890304 and Communication Interface 88890300. Connect the PC to a functional LAN or modem connection and a 120 Volt AC source. Page 3(7) Volvo Trucks North America Field Service Bulletin Date 1.2018 Group No. Release 284 064 01 6 Turn the ignition switch “ON”. 7 Log in to PTT and Identify Vehicle is displayed. 8 Once the vehicle has been identified, enter the Work Order Number information, then click Start Work. W2115477 9 From the Main Menu select Program and then Program Electronic Control Unit 1700-0803-39. Then click Start. W2115478 Page 4(7) Volvo Trucks North America Field Service Bulletin Date 1.2018 Group No. Release 284 064 01 10 Select Engine Control Module (EMS). W2115479 11 Select Program to update the ECM with the latest software. W2115480 Page 5(7) Volvo Trucks North America Field Service Bulletin Date 1.2018 Group No. Release 284 064 01 12 Certain conditions must be met to continue with programming: battery voltage above 10v, parking brake applied, and ignition key in ON position with engine not running. When all conditions have been met, click Continue to proceed with programming. W2115481 13 Select “I accept” to agree to the terms and press continue to proceed. Note: In the United States and Canada, the programing is NOT chargeable. An invoice will not be generated. W2115482 Page 6(7) Volvo Trucks North America Field Service Bulletin Date 1.2018 Group No. Release 284 064 01 14 When programming is complete, click Exit to return to Main Menu to program the ACM. 15 When all programing is complete, clear any diagnostic trouble codes (DTC) and Finish Work. 16 Remove the wheel chocks. W7086759 Reimbursement This repair may be eligible for reimbursement if a product failure was experienced within time and mileage limits of the applicable Warranty coverage. Reimbursement is obtained via the normal claim handling process. UCHP Reimbursement Claim Type (used only when uploading from the Dealer Bus. Sys.) W Labor Code Primary Labor Code (Engine Control Module (ECM) and Aftertreatment Control Module (ACM), Reprogramming) 2841-22-09-16 0.4 hrs. Causal Part 3092091 VOLVO Trucks North America reserves the right to make any changes in design or to make additions to or upon its products without incurring any obligations to install the same on vehicles previously built. Page 7(7)