A13-081

Service Bulletin
May 04, 2018
13-081
09028 Version 14
Warranty Extension: MIL Comes On With DTCs P0301 thru P0304
Supersedes 13-081, dated February 03, 2018, to revise the information highlighted in yellow.
AFFECTED VEHICLES
Year
2011–13
Model
Odyssey
Trim
ALL
VIN Range
Check the iN VIN Status for Eligibility
REVISON SUMMARY
An image was add to REPAIR PROCEDURE B – PISTON CLEANING AND RING REPLACEMENT, Piston Cleaning
and Ring Replacement Procedure.
CORRECTIVE ACTION
2011 Models: Complete diagnosis procedure and if necessary, update PCM software (Procedure A), replace
affected spark plugs then clean pistons and replace the piston rings (Procedure B).
2012–13 Models: Complete diagnosis procedure, replace affected spark plugs then clean the pistons and replace
the pistons rings (Procedure B). No need for software update as 2012–13 model vehicles are equipped with
updated software from factory.
BACKGROUND
American Honda is announcing a powertrain warranty extension as a result of a settlement of a class action captioned,
Soto et al.v. American Honda Motor Co., Inc., Case No. 3:12-cv-1377-SI (N.D. Cal.).
The piston rings on certain cylinders may rotate and align, which can lead to spark plug fouling. This can set DTCs
P0301 No. 1 cylinder misfire detected, P0302 No. 2 cylinder misfire detected, P0303 No. 3 cylinder misfire detected,
P0304 No. 4 cylinder misfire detected, and cause the MIL to come on.
American Honda is extending the powertrain warranty to cover repairs related to engine misfire (that triggers DTCs
P0301 through P0304) to 8 years with unlimited mileage from the original date of purchase and has settled a class
action based on this remedial measure.
This warranty extension does not apply to any vehicle that has ever been declared a total loss or sold for salvage by a
financial institution or insurer, or has a branded or similar title under any state’s law.
CUSTOMER NOTIFICATION
Owners of affected vehicles were sent a class action settlement notice regarding this warranty extension starting in
October 2013.
Before doing work on a vehicle, verify its eligibility by doing an iN VIN status inquiry.
Refer customers seeking information about settlement benefits to www.enginemisfiresettlement.com, or instruct them to
call 888-888-3082.
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools,
equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you
should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information
applies, contact an authorized Honda automobile dealer.
© 2018 American Honda Motor Co., Inc. – All Rights Reserved
Page 1 of 24
DIAGNOSIS
1. Connect the HDS and check for the following DTCs: P0301 No. 1 Cylinder Misfire Detected,
P0302 No. 2 Cylinder Misfire Detected, P0303 No. 3 Cylinder Misfire Detected, P0304 No. 4 Cylinder Misfire
Detected.
Are any of these DTCs stored?
YES – Go to step 2.
NO – Stop. This bulletin does not apply. Continue with normal troubleshooting.
2. Remove and check the spark plug(s) on the affected cylinders (example: if P0301 is stored, check the spark plug on
cylinder No. 1).
Are the spark plug(s) fouled?
YES – Proceed to Step 3.
NO – Stop. This bulletin does not apply. Continue with normal troubleshooting.
Page 2 of 24
3. For 2011 Odyssey only: Check the PCM software version P/N located above the PGM FI Data List.
Year/Model
2011 Odyssey (5-speed A/T)*
Program ID (or later)
V0A560
2011 Odyssey (5-speed A/T)**
V0A240
37805-RV0-A24
2011 Odyssey (6-speed A/T)*
V0A760
37805-RV0-A76
2011 Odyssey (6-speed A/T)**
(VIN before 5FNRL5…CB056992)
V04250
37805-RV0-425
2011 Odyssey (6-speed A/T)**
(VIN including 5FNRL5…CB056992 and after)
V0A360
37805-RV0-A36
2012–13 Odyssey (ALL)
Program P/N (or later)
37805-RV0-A56
Software Updated from Factory
*With Keihin PCM
**With Continental PCM
Is the PCM Program ID and/or Program P/N the same or newer than what is listed above, 2011 model years
only?
NO – The PCM software needs to be updated. Go to REPAIR PROCEDURE A to do the software update, then
go to step 4.
YES – The correct software is installed. The piston rings on select cylinders need to be replaced. Go to step 4.
4. Note which DTCs are stored in the vehicle.
Does the vehicle have DTC P0304 stored? (Any combination of DTCs P0301, P0302, P0303, P0304 may also be
stored.)
YES – Go to REPAIR PROCEDURE B for the cylinders listed, Cylinders 1–4: Clean the pistons, replace the
piston rings, and replace the spark plugs.
NO – Go to REPAIR PROCEDURE B for the cylinders listed below:
 Cylinder 1–3: Clean the pistons and replace the pistons rings.
 Cylinder 1–4: Replace the spark plugs.
Page 3 of 24
WARRANTY CLAIM INFORMATION
PROCEDURE NOTICE: 2011 Models, confirm PCM software is or has been updated with the correct version
(Procedure A). Then piston cleaning, piston ring and spark plug replacement should be done (Procedure B).
Failure to follow this process correctly may result in a full debit of the warranty claim to your dealer.
2012–13 Models: Are equipped with updated software from the factory, no software update is needed. Piston
cleaning, piston ring replacement along with the spark plugs should be performed (Procedure B).
FLAT RATE NOTE: The procedure in this bulletin is different than the service manual. This procedure does not
require the complete removal of the power steering pump, catalytic converter(s), engine and transmission, or the
crankshaft. As a result, the operation number is unique and the FRT is reduced (Procedure B).
OP#
Description
2011–13 Odyssey: Procedure B
Replace piston rings 1–3 and replaced spark
plugs 1–4 (includes diagnosis).
1171H2A 2011 Odyssey: Procedure A
Add to update the PCM on 2011 Odyssey only.
1171H2
1171H2B 2011–13 Odyssey: Add if replacing piston rings on
cylinder 4.
Defect Code:
Flat Rate Time
Failed Part Number
8.5 hrs
13011–5G0–A01
13011-5G0-A01
0.1 hr
13011–5G0–A01
0.8 hr
13011–5G0–A01
5V500
Symptom Code: JB900
Skill Level:
Repair Technician
PARTS INFORMATION FOR REPAIR PROCEDURE A – SOFTWARE UPDATE
There are no parts needed for REPAIR PROCEDURE A because it is a software update only.
Page 4 of 24
PARTS INFORMATION FOR REPAIR PROCEDURE B – PISTON CLEANING AND RING REPLACEMENT
NOTE: Do the DIAGNOSIS first to determine which cylinders you will need to repair.
Required Parts
Part Name
Cyl. Gasket (Fr)
Cyl. Gasket (Rr)
Drain Washer 14 mm
EGR Pipe Gasket A
EGR Pipe Gasket B
Ex. Chamber Gasket
Ex. Pipe Gasket
Head Gasket Fr. (Valve Cover)
Head Gasket Rr. (Valve Cover)
In. Manifold Gasket (Intake Top Cover)
In. Manifold Gasket (In. Manifold to Base)
Oil Filter
O-ring (7.47 mm x 3.6 mm)
O-ring (31.2 mm x 4.1 mm)
Piston Ring Set
Pre-chamber Gasket
Self-locking Nut (8 mm)
Self-locking Nut (10 mm)
Spark Plug
Strainer O-ring
Timing Belt Bolt
Water Gasket Fr.
Water Gasket Rr.
Part Number
12251-R70-A01
12261-R70-A01
94109-14000
18716-R70-A01
18719-R70-A01
18115-R70-A01
18212-SA7-003
12030-R70-A00
12050-R70-A00
17146-R70-A01
17105-RCJ-A01
15400-PLM-A02
91301-PLC-000
91314-PH7-003
13011-5G0-A02
18393-SDB-A00
90212-RCA-A01
90212–SA5-003
12290-R71-L01
15221-RYE-A01
14551-RCA-A01
19411-P8A-A03
19412–P8A-A02
Cyl 1-3
Cyl 1-4
1
1
1
1
2
2
3
1
4
9
4
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
2
2
4
1
8
9
4
1
1
1
1
Part Number
13204–P8A–A01
Cyl 1-3
Cyl 1-4
6
8
90005–PAA–A01
8
16
1
1
1
1
1
2
Replaced Parts as Needed for Repair Procedure B
Part Name
Connecting Rod Bolt (May require up to 6 bolts
per cylinder head)
Washer-Bolt (12 x 163) (May require up to 8
bolts per cylinder head)
REQUIRED MATERIALS – REPAIR PROCEDURE B
Material Description
Honda Long-Life Antifreeze/Coolant Type 2
Full Synthetic Engine Oil 0W-20 Oil
Hondabond HT (1 Tube Repairs 5 Vehicles)
Genuine Honda Throttle Plate Cleaner
Nylon Parts Cleaning Brush
5/16 ID Flexible Hose
Part Number
0L999–9011
08798–9063
08718–0004
08700–9204
(commercially available)
(commercially available)
Quantity
3 gallons
6 quarts
1 tube
TOOL INFORMATION – REPAIR PROCEDURE B
Tool Description
Piston Ring Groove Cleaner
Tool Number
Quantity
07AAZ–TA5A100
1
Page 5 of 24
REPAIR PROCEDURE A – SOFTWARE UDPATE
1.
For 2011 models only, update the PCM software. Refer to Service Bulletin 01-023, Updating Control Units/Modules.
2.
Go to DIAGNOSIS step 4 to determine which pistons need to be repaired before continuing to REPAIR
PROCEDURE B – ENGINE REPAIR.
REPAIR PROCEDURE B – PISTON CLEANING AND RING REPLACEMENT
2011 Models: Confirm PCM software is or has been updated with the correct version (Procedure A). Continue to
(Procedure B).
2012–13 Models: Are equipped with the updated software from the factory, no software update is needed. Piston
cleaning and piston ring replacement along with the spark plugs should only be done after the diagnosis of the spark
plugs has concluded that (Procedure B) is required.
The following service information procedures have been used in full or in part within this service bulletin. For more detail
on these procedures, and torque specifications for some components, refer to the service information.

















Battery Terminal Disconnection and Reconnection
Fuel Pressure Relieving
Fuel Line/Quick-Connect Fitting Removal
Air Cleaner Removal/Installation
Splash Shield Replacement
Drive Belt Removal/Installation
Engine Oil Replacement
Coolant Replacement
Hydraulic Power Steering Fluid Check/Replacement
Intake Manifold Removal and Installation
Timing Belt Removal and Installation
Warm Up-TWC Removal/Installation
Cylinder Head Cover Removal
Cylinder Head Removal and Installation
Piston Ring Replacement
PCM Idle Learn Procedure
Valve Adjustment
Piston Removal Procedure

Use fender covers to avoid damaging painted surfaces.

To avoid damaging any wires and terminals, unplug the circuit connectors carefully while holding the connector
portion.

Mark all the circuits and hoses to avoid misconnection. Make sure they do not contact other circuit wiring, hoses, or
interfere with other parts.
1.
Relieve the fuel pressure.
2.
Remove both front wheels so you can fully lower the vehicle.
3.
Do the battery removal procedure.
Page 6 of 24
4.
Disconnect the fuel feed hose line at the bulkhead.
5.
Remove the engine cover.
Page 7 of 24
6.
Remove the radiator cap.
7.
Raise the vehicle.
8.
Remove the front splash shield.
9.
Drain the engine oil.
10.
Loosen the drain plug on the radiator, and drain the coolant.
11.
Install a 5/16th inner diameter rubber hose on the drain bolt located at the rear of the engine block, loosen the drain
bolt, and drain all remaining coolant. Then disconnect the oil pressure switch connector.
Page 8 of 24
12.
Remove exhaust pipe A.
13.
Depending on the diagnosis, remove the appropriate WU-TWC support bracket bolts.
14.
Remove the EGR lower pipe nuts.
15.
Remove the crankshaft pulley bolt but not the pulley.
NOTE: Make sure to apply new oil to the bolt flange and threads before reinstallation.
16.
Lower the vehicle.
17.
Disconnect the MAP sensor connector and the breather pipe, then remove the intake air duct.
Page 9 of 24
18.
Disconnect the throttle body connector, the EVAP canister purge valve connector, the EVAP hose, the brake booster
vacuum hose, and the vacuum hose.
19.
Disconnect and plug the water bypass hoses.
20.
Remove the drive belt.
21.
Remove the drive belt auto-tensioner.
22.
Remove the power steering pump bolts, the power steering bracket then secure the power steering pump out of the
way.
NOTE: Do not remove any of the hoses.
23.
Remove the engine harness holder bolt on the side engine mount.
24.
Set the engine to TDC cylinder one.
25.
Remove the crankshaft pulley.
26.
Remove the timing belt.
27.
Remove the timing belt idler pulley.
Page 10 of 24
28.
Remove the engine intake upper cover and PCV hose.
29.
Remove the intake manifold bolts and nuts in three steps, then remove the intake manifold.
30.
Remove the PCM cover.
Page 11 of 24
31.
Remove the PCM connectors and harness clip. Remove the battery cables from the underhood fuse box.
32.
Remove the appropriate Ignition coils based on the diagnosis.
NOTE: Depending on the diagnosis, you will either have to remove the rear bank ignition coils or both ignition coil
banks.
Page 12 of 24
33.
Depending on the diagnosis, remove some or all of the following:
 ECT sensor connector
 Front rocker arm oil pressure switch connector
 Rear rocker arm oil pressure switch connector
 CMP sensor connector
 Front A/F sensor one connector
 Rear A/F sensor one connector
 Front secondary HO2S connector
 Rear secondary HO2S connector
 Rocker arm oil control solenoid A connector (bank one)
 Rocker arm oil control solenoid A connector (bank two)
 Rocker arm oil control solenoid B connector (bank one)
 Alternator connector and positive alternator cable
 A/C clutch switch connector
 EGR 5P valve connector
 Engine ground
 Knock sensor
 Fuel injector connectors and clips
34.
Remove the quick-connect fitting cover, then disconnect the fuel feed hose.
35.
Remove the EVAP canister purge joint with the bracket.
Page 13 of 24
36.
Remove the fuel rail connecting joint hose.
37.
Remove the EGR pipe mounting bolts, then remove the EGR pipe.
Page 14 of 24
38.
Separate the water passage from the heads.
39.
Remove the appropriate WU-TWC depending on diagnosis.
NOTE: Set the WU-TWC aside and cover the opening with shop towels to prevent coolant from entering.
Page 15 of 24
40.
Remove the appropriate head with the injector base attached.
NOTE: Depending on diagnosis, you will remove the rear bank head or both heads.
41.
Measure the head bolts to determine if they need replacement. If either diameter is less than 11.3 mm (0.445 in),
replace the cylinder head bolt.
Page 16 of 24
NOTE: Below are the head bolt torque specifications for reinstallation.
 First step: torque the cylinder bolts in sequence to 29 N•m (22 lb-ft).
 Second step: tighten in sequence an additional 90 degrees.
 Third step: tighten in sequence an additional 90 degrees.
 If the bolts are new, tighten an additional 90 degrees.
42. Raise the vehicle.
43. Remove the CKP sensor cover and bolts, then disconnect the CKP sensor connector.
44. Remove the torque converter case cover and the four bolts securing the oil pan to the transmission.
Page 17 of 24
45. Remove all bolts securing the oil pan.
46. Using a flat blade screwdriver, separate the oil pan from the engine block in the areas shown.
47. Remove the oil strainer and baffle plate.
48. Lower the vehicle to a comfortable working height, and place a clean shop towel around the cylinder wall to prevent
debris from entering the coolant passage.
Page 18 of 24
49. Remove the appropriate piston depending on diagnosis, then go to PISTON CLEANING PROCEDURE.
NOTE:
 Before removing the rod caps, use a grease pencil or suitable marking pen to mark each cap and its
corresponding connecting rod with the cylinder number it came from.
 Do not confuse the existing marking on the side of the connecting rod and rod cap with a cylinder number.
They are just manufacturing marks referring to the size of the big end of the rod.
 Installing a rod cap incorrectly will result in engine knock and/or engine failure. Remove and mark one rod
assembly at a time to make sure it is assembled correctly.
 When torqueing the rod cap bolts, refer to the service information for details.
 Click HERE to go to the Tech2Tech® video “Tips When Working with Fracture Rods”.
Piston Cleaning and Ring Replacement Procedure
1. Remove the piston rings from the piston using a ring expander. Be careful not to damage the piston.
2. Spray the piston head and piston ring grooves thoroughly with Honda throttle plate cleaner.
Page 19 of 24
3. While holding the piston upright in your left hand, take the piston ring groove cleaner tool in your right hand and line up
the cleaner tool guides with the second (middle) piston ring groove.
4. Press the handle on the piston ring groove cleaner tool and slide the cleaning bit onto the appropriate piston ring
grooves.
5.
Once the cleaning bit is in the appropriate ring grooves of the piston, make sure the tool handle clicks in to place.
NOTE: There is only one notch on the tool for the handle to engage.
Page 20 of 24
6. Hold the piston steady and rotate the tool counter-clockwise five to six times to remove any carbon deposits in the
piston ring grooves. Do not rotate the tool clockwise.
NOTE: You can watch this procedure in the Tech2Tech segment “How to Clean Piston Ring Grooves”.
7. Remove the piston groove cleaning tool and clean off the carbon from the tool bit.
8. Finish cleaning the piston with throttle plate cleaner and the nylon brush. Do not use a steel wire brush.
Page 21 of 24
NOTE: Below are some examples of before and after pictures. Depending on mileage and running conditions, the
pistons will achieve different levels of cleanliness.
Page 22 of 24
9. Install the piston rings as shown.
NOTE: The first (top) ring has a 1R manufacturing mark and the second (middle) ring has an 2R manufacturing mark.
The manufacturing marks must be facing upward.
10. Position the ring end gaps as shown.
NOTE: If the ring gaps are not positioned correctly, excessive blowby may occur.
11. Apply new engine oil to the piston, the inside of the piston ring compressor, and the cylinder bore.
NOTE: Cylinder wall honing is NOT required for this repair.
Page 23 of 24
12. Install the piston/connecting rod assembly into the cylinder bore with the arrow on top of the piston facing the timing
belt side of the engine.
NOTE: Be careful not to damage the cylinder wall when installing the piston.
13. Measure the diameter of the connecting rod bolts to determine if they need replacement. Calculate the difference in
diameter between point A and point B. It should not be more than 0–0.1 mm (0–0.004 in).
14. Apply new oil to the connecting rod bolt threads and flanges. Torque the bolts to 20 N•m (14 lb-ft) then tighten the
connecting rod bolts an additional 90 degrees.
15.
16.
17.
18.
Reinstall the remaining components in the reverse order of removal.
Replace spark plugs 1–4.
Replace the oil filter and refill all fluids.
Do the idle learn procedure.
END.
Page 24 of 24