TSBELE147
Service Bulletin Details
Public Details for: TSBELE147
Tsb - bms logic improvement for dtc P1B70 - this bulletin provides the procedure to improve the logic of the battery management system (bms) on some 2011-2016my optima hybrid (tf hev) vehicles, produced from february 15, 2011 through july 2
- 2016 - 2015 - 2014 - 2013 - 2012 - 2011 -
Models from 2016
2016 KIA OPTIMA HYBRID |
Models from 2015
2015 KIA OPTIMA HYBRID |
Models from 2014
2014 KIA OPTIMA HYBRID |
Models from 2013
2013 KIA OPTIMA HYBRID |
Models from 2012
2012 KIA OPTIMA HYBRID |
Models from 2011
2011 KIA OPTIMA HYBRID |
GROUP ELE MODEL 2011-2016MY Optima (TF HEV) NUMBER 147 DATE May 2018 TECHNICAL SERVICE BULLETIN SUBJECT: BMS LOGIC IMPROVEMENT FOR DTC P1B70 This bulletin provides the procedure to improve the logic of the Battery Management System (BMS) on some 2011-2016MY Optima Hybrid (TF HEV) vehicles, produced from February 15, 2011 through July 22, 2015, which may experience a malfunction indicator light (MIL) illumination with DTC P1B70 even though there is no actual malfunction. To correct this concern, apply the improved logic to the BMS using the KDS ECU Upgrade function. For confirmation that the latest reflash has been applied to a vehicle you are working on, verify the ROM ID using the table on page 2 of this bulletin. Kia Diagnostic System (KDS) File Under:Circulate To: X General Manager X Service Advisors X Technicians X Service Manager X Parts Manager X Body Shop Manager Fleet Repair Page 2 of 7 BMS LOGIC IMPROVEMENT FOR DTC P1B70 SUBJECT: ECU Upgrade Procedure: To correct this condition, the ECU should be reprogrammed using the KDS download, as described in this bulletin. Upgrade Event Name 368.TF HEV BMS ON DTC (P1B70) LOGIC IMPROVEMENT NOTICE A fully charged battery is necessary before ECU upgrade can take place. It is recommended that the Midtronics GR8-1299 system be used in ECU mode during charging. DO NOT connect any other battery charger to the vehicle during ECU upgrade. All ECU upgrades must be done with the ignition key in the ‘ON’ position. Be careful not to disconnect the VCI-II connected to the vehicle during the ECU upgrade procedure. DO NOT start the engine during ECU upgrade. DO NOT turn the ignition key ‘OFF’ or interrupt the power supply during ECU upgrade. When the ECU upgrade is completed, turn the ignition ‘OFF’ and wait 10 seconds before starting the engine. ONLY use approved ECU upgrade software designated for the correct model, year. NOTICE Before attempting an ECU upgrade on any Kia model, make sure to first determine whether the particular model is equipped with an immobilizer security system. Failure to follow proper procedures may cause the PCM to become inoperative after the upgrade and any claims associated with this repair may be subject to chargeback. ROM ID INFORMATION TABLE: Upgrade Event #368 Model TF HEV System BMS ECU P/No. ROM ID Previous New 37513 4R000 4600, 4700, 4800, 4900, 5080 5180 37513 4R000 4920, 4940, 4960, 5060 5160 5020, 5200, 5300, 5500 5340, 5400 To verify the vehicle is affected, be sure to check the Calibration Identification of the vehicle's ECM ROM ID and reference the Information Table as necessary. 37513 4R100 TSB: ELE147 Optima (TF HEV) May 2018 Page 3 of 7 BMS LOGIC IMPROVEMENT FOR DTC P1B70 SUBJECT: NOTICE Prior to performing the ECU upgrade, be sure to check that the KDS is fully charged. 1. Connect the VCI-II to the OBD-II connector, located under the driver’s side of the instrument panel. NOTICE The ECU upgrade function on KDS operates wirelessly. It is not necessary to perform the upgrade via USB cable. 2. With the ignition ON, turn ON the KDS tablet. Select KDS from the home screen. 3. Confirm communication with VCI (A) and then configure the vehicle (B) using the AUTO VIN (C) feature. B A C 4. Select ECU Upgrade. TSB: ELE147 Optima (TF HEV) May 2018 Page 4 of 7 SUBJECT: 5. BMS LOGIC IMPROVEMENT FOR DTC P1B70 The KDS will check the server for recently uploaded Events and then automatically download Upgrade Event #368. NOTICE The vehicle must be identified in Vehicle Selection to download an Event for that vehicle. 6. KDS screenshot shown above is for demonstration purposes only. Events shown in screenshot are not applicable to this bulletin. Select Auto Mode. CAUTION Do NOT attempt to perform a Manual Mode upgrade UNLESS Auto Mode fails. Always follow the instructions given on the KDS in either Auto or Manual mode. 7. Select the BMS system under the System selection menu. D Touch ID Check (D) and confirm that the latest update is available. Select Upgrade Event #368 and select Upgrade to continue. 8. The ECU upgrade will begin and the progress of the upgrade will appear on the bar graph. Upgrade part (1/2) (E) will download the upgrade event to the VCIII. Upgrade part (2/2) (F) will upgrade the ECU. CAUTION Do not touch the system buttons (like ‘Back’, ‘Home’, ‘etc.’) while performing ECU Upgrade. TSB: ELE147 Optima (TF HEV) May 2018 E F Page 5 of 7 SUBJECT: 9. BMS LOGIC IMPROVEMENT FOR DTC P1B70 If a “Communication Fail” screen appears, verify that the VCI-II and KDS are communicating properly. Touch OK and restart the procedure from step 4. NOTICE If an error notice continues to appear or if the upgrade cannot be performed, contact Techline or GIT America Help Desk. 10. When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on. Touch OK to continue. 11. Once the upgrade is complete, touch OK to finalize the procedure. 12. When prompted, select YES to check for Diagnostic Trouble Codes (DTC) and erase any DTCs stored such as EPS, ESC, and TPMS that may have been set during the upgrade. 13. Start the engine to confirm proper operation of the vehicle. TSB: ELE147 Optima (TF HEV) May 2018 Page 6 of 7 BMS LOGIC IMPROVEMENT FOR DTC P1B70 SUBJECT: Manual Upgrade Procedure: NOTICE The manual upgrade should ONLY be performed if the automatic upgrade fails. If the automatic upgrade fails, turn the ignition OFF for about 10 seconds then place it back in the ON position to reset the control unit BEFORE performing manual upgrade. See table below for Manual Mode passwords. Manual Mode ECU Upgrade Passwords Menu TF HEV BMS (4600,4700,4800,4900,5080) : 37513 4R000 TF HEV BMS (4920,4940,4960,5060) : 37513 4R000 TF HEV BMS (5020,5200,5300,5340,5400) : 37513 4R100 Password 4000 4001 4100 1. Within the ECU Upgrade screen displayed, select Manual Mode. 2. Select the BMS system under the System selection menu. Select Upgrade Event #368 and select Upgrade to continue. 3. Select the appropriate control unit part number with reference to the ROM ID Information Table on page 2, and select OK. 4. Enter the appropriate password from the Manual Mode password table above and select OK. 5. The upgrade will begin and the progress of the upgrade will appear on the bar graph. 6. When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on. Touch OK to continue. 7. Once the upgrade is complete, touch OK to finalize the procedure. 8. When prompted, select YES to check for Diagnostic Trouble Codes (DTC) and erase any DTCs stored such as EPS, ESC, and TPMS that may have been set during the upgrade. 9. Start the engine to confirm proper operation of the vehicle. TSB: ELE147 Optima (TF HEV) May 2018 Page 7 of 7 BMS LOGIC IMPROVEMENT FOR DTC P1B70 SUBJECT: AFFECTED VEHICLE RANGE: Model Production Date Range Optima (TF HEV) February 15, 2011 through July 22, 2015 WARRANTY INFORMATION: N Code: I3A C Code: ZZ3 Claim Type Causal P/N Qty. Repair Description Labor Op Code Op Time Replacement P/N Qty. W Use BMS Part No. by using VIN Look-up on EPC 0 BMS Logic Improvement for DTC P1B70 37513F06 0.3 M/H N/A 0 TSB: ELE147 Optima (TF HEV) May 2018