SSM74008
Service Bulletin Details
Public Details for: SSM74008
Automatic transmission oil leaks (8hp45/75) resulting in transmission sump replacements.
- 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 -
Models from 2016
2016 JAGUAR F-TYPE |
2016 JAGUAR XF |
2016 JAGUAR XJ |
Models from 2015
2015 JAGUAR F-TYPE |
2015 JAGUAR XJ |
Models from 2014
2014 JAGUAR F-TYPE |
2014 JAGUAR XJ |
Models from 2013
2013 JAGUAR XJ |
Models from 2012
2012 JAGUAR XJ |
Models from 2011
2011 JAGUAR XJ |
Models from 2010
2010 JAGUAR XJ |
9/19/2018 TOPIx - SSM74008 - 8HP45/75 Automatic Transmission Oil Leak Reference SSM74008 Models E-PACE / X540 F-PACE / X761 F-TYPE / X152 XE / X760 XF / X260 XJ / X351 Title 8HP45/75 Automatic Transmission Oil Leak Category Driveline Last modified 18-Sep-2018 00:00:00 Symptom 501000 Automatic Transmission Concerns Attachments Sump 21.pdf (Sump 21.pdf) Sump Pan Breakaway Torques1.docx (Sump Pan Breakaway Torques1.docx) Content Issue: Automatic transmission oil leaks (8HP45/75) resulting in transmission sump replacements. Cause: Unknown at this time and Engineering investigating root cause. Action: To ensure correct diagnosis and repair please carry out the following steps: 1. Raise vehicle on ramp 2. Using a suitable degreaser, thoroughly degrease the suspected component all the way around as well as, approximately, 25-50mm (1-2 inches) above the suspected leak 3. Using an air gun, make sure all traces of oil are removed from the bolts/thread attached to the sump pan. 4. Using a suitable leak detector spray, thoroughly coat the suspected component as well as, approximately, 25-50mm (1-2 inches) above the suspected leak, C2C42090 5. Allow to sit for a couple minutes to ensure all oil has been cleaned off 6. Take a clear, in focus photo of the spray on the suspected area before proceeding. 7. Reassemble vehicle and complete a suitable road test and make sure that the engine gets to normal operating temperature 8. Return the vehicle to workshop and raise on ramp 9. Inspect the suspected component for fluid leaks, the detector spray should leave a trace from the leak area 10. Identify leaking position: If a leaking point has been identified on the sump pan, take a clear, in focus photo of the leaking position. Proceed to 10. If a leaking point has not been identified, proceed to 11 11. At the customer’s convenience, raise a TA attaching photos of the sump pan requesting a visit from ZF MS engineering. The TA will advise whether to proceed with repair or whether a ZF engineer will visit the site. 12. If a leaking position has not been identified, check the following areas: Check Technical Bulletins reference Automatic Transmission leaks Transmission output shaft seal Transmission oil cooler pipes not secured correctly Transmission electrical plug 13. If a sump pan replacement is required, record the breakaway torques for the sump pan bolts (as detailed in attachment) and raise an EPQR attaching photos of leak and breakaway torque attachment. Technicians - Please rate this SSM and provide comments so that future communications can be improved. 1 = Poor – Basic information provided – The SSM does not help me resolve the customer concern. 3 = Average – Adequate information provided – The SSM partially helps me resolve the customer concern. 5 = Excellent – All required information provided to resolve the customer concern. https://topix.landrover.jlrext.com/topix/content/document/view?id=926646 1/1