TSB17-110-001A

Spartan Motors USA, Inc.
DATE:
APPLIES TO:
Technical Service Bulletin
01/25/2018
This service bulletin applies to the Emergency Response chassis cabs
listed below by Model and Model Year, built between March 26, 2004 to
August 8, 2016.
Model
Model Year
Advantage
2005 – 2009
Diamond
2004 – 2008
Gladiator
2004 – 2017
MetroStar
2006 – 2017
MetroStar R/T
2010 - 2014
Bulletins TSB17-110-001 and TSB17-110-002 are superseded by
bulletins TSB17-110-001A and TSB17-110-002A in order to
accommodate S-2680-001 and S-2680-002 Electrical Instruction
Addendum and the removal of polyurea coating such as Line-X® Any
vehicle repaired under these bulletin #’s will not require any additional
work.
CONDITION:
Door hinge may deform causing door to sag.
CORRECTION:
Replace door hinges, door latches, strikers and door seals.
LABOR ALLOCATION:
Max 2.5 Hrs. per door or Pre-approved estimate.
CLASSIFICATION:
E1
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 1 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
PARTS NEEDED:
QTY
1
Part Number
S-2587-001D
Description
KIT-SERVICE DOOR HINGE, MFD +
FLAT ROOF
Part Number
67201212
67201213
17200723
61200596
0533-EE3-001
0533-EE3-002
0550-EE3-001
0764-EE3
0253-ZZ4
1249-RR1
0202-BB1-017
Description
FRONT DOOR HINGE
REAR DOOR HINGE
REINFORCEMENT PLATE
WASHER
ASM-LATCH LH
ASM-LATCH RH
STRIKER-DOOR LATCH
INSTL-DOOR LATCH, FRONT DOORS
STRIKER/LATCH PROCESS
D-SEAL
SCREW-M6-1.0X16MM TORX DR
PAN HD MACH,ZINC,W/THD LOCK
NUT-FLANGE 6MM X 1.0 ZINC
INSTRUCTION DOCUMENT - ENGLISH
INSTRUCTION DOCUMENT - FRENCH
ELECTRICAL INSTRUCTION
ADDENDUM - ENGLISH
ELECTRICAL INSTRUCTION
ADDENDUM - FRENCH
Kit # S-2587-001D Contains:
QTY
2
2
4
84
2
2
4
1
1
48 FT
16
8
1
1
1
M06100FNZ
TSB17-110-001A
TSB17-110-002A
S-2680-001
1
S-2680-002
______________________________________________________________________________
QTY
Part Number
1
Description
S-2588-001D
KIT-SERVICE DOOR HINGE, MFD + 10”
RAISED ROOF
Kit # S-2588-001D Contains:
QTY
2
2
Part Number
67201212
67201214
Description
FRONT DOOR HINGE
REAR DOOR HINGE
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 2 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
4
84
2
2
4
1
1
48 FT
16
17200723
61200596
0533-EE3-001
0533-EE3-002
0550-EE3-001
0764-EE3
0253-ZZ4
1249-RR1
0202-BB1-017
8
1
1
1
M06100FNZ
TSB17-110-001A
TSB17-110-002A
S-2680-001
1
S-2680-002
QTY
1
Technical Service Bulletin
REINFORCEMENT PLATE
WASHER
ASM-LATCH LH
ASM-LATCH RH
STRIKER-DOOR LATCH
INSTL-DOOR LATCH, FRONT DOORS
STRIKER/LATCH PROCESS
D-SEAL
SCREW-M6-1.0X16MM TORX DR
PAN HD MACH,ZINC,W/THD LOCK
NUT-FLANGE 6MM X 1.0 ZINC
INSTRUCTION DOCUMENT
INSTRUCTION DOCUMENT
ELECTRICAL INSTRUCTION
ADDENDUM - ENGLISH
ELECTRICAL INSTRUCTION
ADDENDUM - FRENCH
Part Number
S-2589-001D
Description
KIT-SERVICE DOOR HINGE, MFD + 20”
RAISED ROOF
Part Number
67201212
67201215
17200723
61200596
0533-EE3-001
0533-EE3-002
0550-EE3-001
0764-EE3
0253-ZZ4
1249-RR1
0202-BB1-017
Description
FRONT DOOR HINGE
REAR DOOR HINGE
REINFORCEMENT PLATE
WASHER
ASM-LATCH LH
ASM-LATCH RH
STRIKER-DOOR LATCH
INSTL-DOOR LATCH, FRONT DOORS
STRIKER/LATCH PROCESS
D-SEAL
SCREW-M6-1.0X16MM TORX DR
PAN HD MACH,ZINC,W/THD LOCK
NUT-FLANGE 6MM X 1.0 ZINC
Kit # S-2589-001D Contains:
QTY
2
2
4
90
2
2
4
1
1
48 FT
16
8
M06100FNZ
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 3 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
1
1
1
TSB17-110-001A
TSB17-110-002A
S-2680-001
1
S-2680-002
QTY
1
Technical Service Bulletin
INSTRUCTION DOCUMENT
INSTRUCTION DOCUMENT
ELECTRICAL INSTRUCTION
ADDENDUM - ENGLISH
ELECTRICAL INSTRUCTION
ADDENDUM - FRENCH
Part Number
S-2590-001D
Description
KIT-SERVICE DOOR HINGE, SMFD
FLAT ROOF
Part Number
67201212
67201224
17200723
61200596
0533-EE3-001
0533-EE3-002
0550-EE3-001
0764-EE3
0253-ZZ4
1249-RR1
0202-BB1-017
Description
FRONT DOOR HINGE
REAR DOOR HINGE
REINFORCEMENT PLATE
WASHER
ASM-LATCH LH
ASM-LATCH RH
STRIKER-DOOR LATCH
INSTL-DOOR LATCH, FRONT DOORS
STRIKER/LATCH PROCESS
D-SEAL
SCREW-M6-1.0X16MM TORX DR
PAN HD MACH,ZINC,W/THD LOCK
NUT-FLANGE 6MM X 1.0 ZINC
INSTRUCTION DOCUMENT
INSTRUCTION DOCUMENT
ELECTRICAL INSTRUCTION
ADDENDUM - ENGLISH
ELECTRICAL INSTRUCTION
ADDENDUM - FRENCH
Kit # S-2590-001D Contains:
QTY
2
2
4
84
2
2
4
1
1
48 FT
16
8
1
1
1
M06100FNZ
TSB17-110-001A
TSB17-110-002A
S-2680-001
1
S-2680-002
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 4 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
QTY
Part Number
1
Description
S-2594-001D
Technical Service Bulletin
KIT-SERVICE DOOR HINGE 2 DOOR
CAB
Kit # S-2594-001D Contains:
QTY
2
4
42
1
1
2
1
1
12 FT
8
Part Number
67201212
17200723
61200596
0533-EE3-001
0533-EE3-002
0550-EE3-001
0764-EE3
0253-ZZ4
1249-RR1
0202-BB1-017
4
1
1
1
M06100FNZ
TSB17-110-001A
TSB17-110-002A
S-2680-001
1
S-2680-002
Description
FRONT DOOR HINGE
REINFORCEMENT PLATE
WASHER
ASM-LATCH LH
ASM-LATCH RH
STRIKER-DOOR LATCH
INSTL-DOOR LATCH, FRONT DOORS
STRIKER/LATCH PROCESS
D-SEAL
SCREW-M6-1.0X16MM TORX DR
PAN HD MACH,ZINC,W/THD LOCK
NUT-FLANGE 6MM X 1.0 ZINC
INSTRUCTION DOCUMENT
INSTRUCTION DOCUMENT
ELECTRICAL INSTRUCTION
ADDENDUM - ENGLISH
ELECTRICAL INSTRUCTION
ADDENDUM - FRENCH
GENERAL INSTRUCTIONS:
Thoroughly review entire service bulletin before starting work. If there are questions or concerns
with steps defined in this service bulletin, contact Spartan Motors USA, Inc. Customer & Product
Support Group.
All applicable industry safety standards must be followed when performing work identified in
this procedure.
NOTE: This bulletin applies to all cab doors.
STEP-BY-STEP INSTRUCTIONS:
1. Remove door check strap from door. Take care not to allow the door to swing open and hit /
damage side of cab. Refer to FIG. 6-1.
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 5 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
2. Examine check strap for signs of elongation. If the leading edge of the door skin contacts the
side of cab when the door is fully opened with light forward pressure, the check strap should
be replaced to prevent damage. Replacement part number for door check strap is 0697-EE3001.
Remove bolts using
7/16” socket. Retain for
reinstallation
FIG 6-1
3. Roll window all the way down to prevent glass from falling when un-hooked from door panel.
4. Remove door panels. While removing the door panels the window regulator will need to be
disconnected from the door glass. Refer to FIG. 7-1, FIG. 7-2 and FIG. 8-1.
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 6 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Remove door panel fasteners starting
from the rear of the door. Remove
enough fasteners to allow access to
disconnect window regulator from
glass and door latch linkage rods from
paddle handle. Once these are
disconnected door panel can be
removed.
Rear of door
FIG. 7-1
Remove two fasteners that
mount power window regulator
to door panel.
Ensure window is down and is
resting on window stop.
Power window configuration
FIG. 7-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 7 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Remove regulator from glass channel in manual
window regulator configurations.
Ensure window down is resting on
window stop.
Manual Window Configuration
FIG. 8-1
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 8 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
5. For view showing front door with door panel removed. Refer to FIG. 9-1.
Front door shown with
door panel removed.
FIG. 9-1
6. While removing the door panels the door latch rods will need to be disconnected. Refer to
FIG. 9-2.
Remove door latch rods
from back of paddle
handle by pressing the
clips off the rods then
slide rods out of clips.
Ensure clips stay in place
on back of paddle handle.
FIG. 9-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 9 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
7. While removing the door panels any electrical wires connected to the door panels such as
power window switches or door lights will need to be disconnected. Reference S-2680-001
Electrical Instruction Addendum.
8. Disconnect all wiring that may go through the door hinge for items such as power mirrors
(removal of mirror may be necessary to access connector for de-pinning), door lights and
power windows. Wire pass through spring(s) will need to be removed and retained for reuse. Refer to FIG. 10-1. Reference S-2680-001 Electrical Instruction Addendum.
Wire pass through spring. Spring
also shown removed.
FIG. 10-1
9. Inspect wires for chaffing and repair/replace any wires where the insulation is worn or not
present. Reference S-2680-001 Electrical Instruction Addendum.
10. Remove and discard the door latch and fasteners. NOTE: two fasteners toward outside of
door utilize nuts to secure the latch to the door frame. Ensure these do not fall into the
doorframe when removing or installing parts. Refer to FIG. 11-1.
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 10 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Torque fasteners to 45 lbf-in.
Remove and discard latch.
FIG. 11-1
11. Inspect the area beneath the latch for a polyurea coating such as Line-X®. Refer to FIG. 12-1.
If such a coating is present beneath the latch, it must be removed prior to installing the new
latch. To remove the coating, mark the area to be removed as shown in figure 12-2. Score the
coating along the boundary with a utility knife. Use a scraper to remove the coating from the
area. Paint may be applied to the area to enhance appearance. Refer to FIG. 12-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 11 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
¾”
6 ¾”
¾”
POLYUREA COATING
(Line-X)
REMOVE COATING FROM THIS AREA THEN
PAINT TO ENHANCE APPEARANCE
FIG. 12-2
FIG. 12-1
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 12 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
12. Inspect the area beneath the latch logic on the inside of the door frame for a polyurea coating
such as Line-X®. Refer to FIG. 13-1. If a coating is present beneath the latch logic (Latch logic
mounting surface), it must be removed prior to installing the new latch. Use a scraper or
similar tool to remove the coating from the area.
VIEW FROM
OUTSIDE DOOR
VIEW FROM
INSIDE DOOR
VIEW FROM
INSIDE DOOR
LOOK INSIDE
DOOR
LATCH LOGIC
MOUNTING
SURFACE
LATCH LOGIC
FIG. 13-1
13. Inspect threaded mounting holes in latch logic for damage. Refer to FIG. 14-1. Replace latch
logic (P/N 0557-EE3-001 LH, 0534-EE3-001 RH) if thread damage is present.
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 13 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
INSPECT
THREADED
HOLES FOR
DAMAGE
FIG. 14-1
14. Install new door latches and fasteners: P.N. 0533-EE3-001, 0533-EE3-002, 0202-BB1-017 and
M06100FNZ. NOTE: two fasteners toward outside of door utilize nuts for mounting. Ensure
these do not fall into the door frame when removing or installing parts. Torque fasteners to
45 lbf-in. Refer to FIG. 15-1, FIG. 15-2 and FIG. 16-1.
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 14 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
INSTALL NEW
FASTENERS AND
TORQUE TO 45 lbf-in.
INSTALL NEW
DOOR LATCH
FIG. 15-1
Control
levers
shown
assembled
in door
FIG. 15-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 15 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Ensure control
levers are
engaged properly
when assembled.
Shown with door
removed for
better clarity.
FIG.16-1
15. Remove the door latch striker: P.N. 0550-EE3-001. Refer to FIG. 16-2
REMOVE LATCH STRIKER
FIG16-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 16 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
16. Inspect the area beneath the latch striker for a polyurea coating such as Line-X®. Refer to FIG.
17-1. If such a coating is present beneath the latch striker, it must be removed prior to
installing the new latch striker. To remove the coating, mark the area to be removed as shown
in figure 17-2. Score the coating along the boundary with a utility knife. Use a scraper to
remove the coating from the area. Paint may be applied to the area to enhance appearance.
Refer to FIG. 17-2
1/4”
4”
1/4”
POLYUREA COATING
(Line-X)
REMOVE COATING FROM THIS AREA THEN
PAINT TO ENHANCE APPEARANCE
FIG. 17-1
FIG. 17-2
17. Replace the door latch striker with P.N. 0550-EE3-001. Install striker snug tight. Final
adjustments will be made after hinge replacement and door positioning. Refer to FIG. 18-1
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 17 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Install new striker per 0764-EE3
print and adjust per striker latch
process 0253-ZZ4.
FIG. 18-1
18. Support the weight of the door in an opened position in preparation for removing the door
hinge. Door weights approximately 150-200 lbs.
19. Once door is supported remove door hinge fasteners. Retain for re-use. Properly dispose of
old hinge and washers. Refer to FIG. 18-2.
Hinge bolt
Existing hinge mounting
washer (.75 OD) properly
dispose of these when
removed
New Belleville washer (.93 OD)
washer P.N. 61200596
FIG.18-2
20. Ensure that bolts and washers are clean and dry then reinstall new door hinge using retained
bolts, new washers, (P.N. 61200596) and (2) reinforcement plates (P.N. 17200723) at each
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 18 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
front door. No reinforcement plates required for the rear doors. For proper washer
installation Refer to FIG. 19-1, 19-2 and FIG. 20-1.
Hinge Bolt
Hinge
Washer
FIG. 19-1
Add backer plate at
this leaf top and
bottom of door
Add washers at all fasteners
for hinge mounting
FIG. 19-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 19 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Front door showing new
hinge and (2) backer
plates installed.
FIG.20-1
21. Once the hinge is properly aligned the hinge mounting fasteners must be torqued to 11-13
lbf-ft. Refer to FIG. 20-2.
Door alignment should
be .25” to .31” gap
around perimeter.
Paint break line or
pinstripe lined up and
outside of door skin
flush with sides of cab
and front skin
FIG.20-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 20 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
22. Once hinge is changed and door is aligned, any electrical items in the door that were removed
can be re-connected and secured. Reinstall retained wire pass through spring (s) and secure
them. Reference S-2680-001 Electrical Instruction Addendum.
23. Reinstall retained door panels. During door panel re-installation, window regulator and door
latch rods must be re-connected. Ensure rod clips are clipped onto rods securely. Refer to
FIG. 21-1.
View of back of paddle
handle showing rod
connections
Rod installed through clip snapped
onto rod securely
FIG. 21-1
24. For power window regulator alignment Refer to FIG 22.1.
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 21 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Install these two fasteners loosely
initially during re-installation. For
final adjustment window needs
to be rolled down approx. . . . 6”
then two fasteners to be fully
driven, seated and not stripped.
This will allow the regulator to go
up and down smoothly.
Power window configuration shown
FIG. 22-1
25. New door seals will need to be applied to new door hinges. Refer to FIG. 22-1, FIG. 23-1, FIG.
23-2, FIG. 24-1 and FIG. 24-2.
Hinge door
side
Hinge cab side
35” seal
36” Seal
For proper door hinge seal
installations make sure all
surfaces are cleaned with
isopropyl alcohol before
applying seals.
FIG.22-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 22 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
Front door seals
FIG. 23-1
Top of door
“A” seal length
“B” seal length
“C” seal length
Inside of door
Rear door
FIG.23-2
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 23 of 24
QUA-FR-0290
Rev: 3.0
Spartan Motors USA, Inc.
Technical Service Bulletin
FIG.24-1
Top of door
Rear door seals
FIG.24-2
26. Once door panel is re-installed and all fasteners are tightened the door check strap can be
re-installed. Door check strap fasteners to be torqued to 80-90 lbf-in.
27. At this time final adjustments to door latch striker can be made per striker/latch process
0253-ZZ4.
28. END
Service Bulletins are intended for use by Professional Technicians only. They are written to guide Professional Technicians in performing service to
vehicles of specific nature in conjunction with industry standards. Professional Technicians should be appropriately trained on industry standards and
have the tools and equipment to perform procedures safely and properly.
17005
Page 24 of 24
QUA-FR-0290
Rev: 3.0