MT-010-18
Service Bulletin Details
Public Details for: MT-010-18
- 2019 - 2018 - 2017 - 2016 - 2015 - 2014 -
Models from 2019
2019 MAZDA CX-3 |
2019 MAZDA CX-5 |
2019 MAZDA CX-9 |
2019 MAZDA MX-5 |
Models from 2018
2018 MAZDA CX-3 |
2018 MAZDA CX-5 |
2018 MAZDA CX-9 |
2018 MAZDA MAZDA3 |
2018 MAZDA MAZDA6 |
2018 MAZDA MX-5 |
Models from 2017
2017 MAZDA CX-3 |
2017 MAZDA CX-5 |
2017 MAZDA CX-9 |
2017 MAZDA MAZDA3 |
2017 MAZDA MAZDA6 |
2017 MAZDA MX-5 |
Models from 2016
2016 MAZDA CX-3 |
2016 MAZDA CX-5 |
2016 MAZDA CX-9 |
2016 MAZDA MAZDA3 |
2016 MAZDA MAZDA6 |
2016 MAZDA MX-5 |
Models from 2015
2015 MAZDA MAZDA3 |
Models from 2014
2014 MAZDA MAZDA3 |
Mazda North American Operations Irvine, CA 92618-2922 M-Tips Subject: DTC U0323/U0423/U3000 CANNOT BE DELETED M-Tips No.: MT-010/18 Last Issued: 11/27/2018 BULLETIN NOTES This M-Tip supersedes the previously issued M-Tip(s) listed below: The changes are noted in Red. Previous M-TIPs: Date(s) Issued: MT-002/16 12/20/16 APPLICABLE MODEL(S)/VINS 2014-2018 Mazda3 2016-2019 MX-5 2016-2019 CX-5 2016-2018 Mazda6 2016-2019 CX-3 2016-2019 CX-9 DESCRIPTION Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The “ROOM” fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected. REPAIR PROCEDURE 3. 4. 5. Confirm the CMU is connected. Confirm the ROOM fuse is installed properly. Change the Temperature and the Distance setting in MAZDA CONNECT System Settings. Temperature - Fahrenheit to Celsius (or vice versa) Distance - Miles to Kilometers (or vice versa) Page 1 of 2 An editorial board comprised of MNAO service staff members generates, collects, and verifies information for this publication. To contribute repair tip ideas, send an e-mail to [email protected]. All contributions become property of MNAO, which assumes permission to publish them without further consideration. © 2018 Mazda North American Operations, U.S.A. M-Tips No.: MT-010/18 Last Issued: 11/27/2018 4. Turn the ignition OFF. 5. Remove the ROOM fuse. 6. Press and hold the tripmeter reset button more than 5 seconds. 7. Install the ROOM fuse. 8. Turn the ignition ON. 9. Delete the DTC(s) using M-MDS. 10. Return the original unit of Temperature and Distance in MAZDA CONNECT System Settings. Note: If DTC codes do not clear, refer to Workshop Manual DTC U0323 [SKYACTIV-G]. Page 2 of 2 An editorial board comprised of MNAO service staff members generates, collects, and verifies information for this publication. To contribute repair tip ideas, send an e-mail to [email protected]. All contributions become property of MNAO, which assumes permission to publish them without further consideration. © 2018 Mazda North American Operations, U.S.A.