LTB01262NAS1

2/6/2019
LTB01262NAS1 - 'Check Pedestrian System' Message Displayed On The Instrument Cluster | TOPIx
LT B 0 1 2 6 2 N A S 1
TECHNICAL BULLETIN
23 JAN 2019
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians
with the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land
Rover service facility to determine whether this bulletin applies to a specific vehicle.
I N F O R M AT I O N
SECTION:
501-20
S U B J E C T/ C O N C E R N :
'Check Pedestrian System' Message Displayed On The Instrument Cluster
AFFECTED VEHICLE RANGE:
MODEL:
Discovery Sport (LC)
MODEL YEAR:
2015-2017
https://topix.landrover.jlrext.com/topix/content/document/view?id=952409
VIN:
500001-721747
ASSEMBLY PLANT:
Halewood
1/5
2/6/2019
LTB01262NAS1 - 'Check Pedestrian System' Message Displayed On The Instrument Cluster | TOPIx
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
A 'Check Pedestrian System' message may be displayed on the Instrument Cluster. Upon further
diagnosis, DTC (Diagnostic Trouble Code) B1475-96 may be stored in the Restraints Control Module
(RCM).
CAUSE:
This may be caused by a RCM software error.
ACTION:
Should a customer express this concern, follow the Diagnostic Procedure below.
PA RTS :
No Parts Required
TOOLS:


Jaguar Land
Rover-approved
battery power
supply
Jaguar Land
Rover-approved
diagnostic
equipment with
latest SDD
Software
Management Pack
WARRANT Y:
https://topix.landrover.jlrext.com/topix/content/document/view?id=952409
2/5
2/6/2019
LTB01262NAS1 - 'Check Pedestrian System' Message Displayed On The Instrument Cluster | TOPIx
NOTES:
Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Use TOPIx to obtain the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Read and clear fault codes (followed by Configure existing
Restraints Control Module [RCM])
12.90.16.01
0.1
04
LR072723
Configure existing Restraints Control Module (RCM)
86.95.15
0.2
04
LR072723
Read and clear fault codes (no further action)
12.90.16
0.2
04
LR072723
NOTE:
Normal Warranty procedures apply.
DIAGNOSTIC PROCEDURE:
CAUTIONS:
A Jaguar Land Rover-approved battery power supply must be connected to the vehicle
startup battery.
All ignition ON/OFF requests MUST be performed; failure to do these steps may cause
damage to vehicle control modules.
1
2
Connect the Jaguar Land Rover-approved battery power supply to the vehicle startup battery.
NOTE:
The Jaguar Land Rover-approved diagnostic equipment must be loaded with
SDD155.04 Software Management Pack v309 (or later).
https://topix.landrover.jlrext.com/topix/content/document/view?id=952409
3/5
2/6/2019
LTB01262NAS1 - 'Check Pedestrian System' Message Displayed On The Instrument Cluster | TOPIx
Connect the Jaguar Land Rover-approved diagnostic equipment to the vehicle and begin a
new session.
3
Follow all on-screen instructions.
4
Read and clear all DTC.
5
Switch the vehicle ignition OFF.
6
Switch the vehicle ignition ON.
7
Follow all on-screen instructions.
8
Read all DTC.
If DTC B1475-96 is stored in the Restraints Control Module (RCM), do not
continue with this Technical Bulletin.
Continue diagnosis using TOPIx Workshop Manual section 501-20B:
Supplementary Restraint System - Diagnosis and Testing - Airbag and
Seatbelt Pretensioner Supplemental Restraint System.)
If DTC B1475-96 is not stored in the RCM, go to the next Step.
9
If the hyperlink is not available:
1 Select Diagnosis from the Session Type screen.
2 Select the Selected Symptoms tab.
3 Select Electrical - Instruments - Information and message center - Message display
area - Body
4 Run and close the Datalogger tool to reveal the 'Extras' tab.
5 Select the Extras tab.
6 Select Run to perform the 'Configure existing module - Restraints control module'
option.
10
Follow all on-screen instructions until the application finishes successfully.
https://topix.landrover.jlrext.com/topix/content/document/view?id=952409
4/5
2/6/2019
LTB01262NAS1 - 'Check Pedestrian System' Message Displayed On The Instrument Cluster | TOPIx
1 Select the Clear DTCs option following completion of the software download.
2 Follow the on-screen instructions until the application finishes successfully.
11
Exit the current session.
1 Select the Session tab.
2 Select the Close Session option.
12
Disconnect the diagnostic equipment and battery power supply from the vehicle.
https://topix.landrover.jlrext.com/topix/content/document/view?id=952409
5/5