NTB18-032a
Service Bulletin Details
Public Details for: NTB18-032a
Altima and maxima; noise from trunk area this bulletin has been amended. See amendment history on the last page. Please discard previous versions of this bulletin.
Models from 2019
2019 NISSAN MAXIMA |
Models from 2018
2018 NISSAN ALTIMA |
2018 NISSAN MAXIMA |
Models from 2017
2017 NISSAN MAXIMA |
Classification: Reference: BT18-003a Date: NTB18-032a February 19, 2019 ALTIMA AND MAXIMA; NOISE FROM TRUNK AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. APPLIED VEHICLES: 2018 Altima (L33) 2017-2019 Maxima (A36) APPLIED VINS: Altima: Vehicles built from 1N4(*)L3A(**)JC 100261 to 1N4(*)L3A(**)JC 127731 2017 Maxima: Vehicles built after 1N4AA6A(**)HC 444883 2018 Maxima: All 2019 Maxima: Vehicles built before 1N4AA6A(**)KC 370720 APPLIED DATES: Altima: Vehicles built from August 1, 2017 to October 11, 2017 Maxima: Vehicles built from August 1, 2017 to February 1, 2019 IF YOU CONFIRM A ticking, tapping, or popping type of noise is coming from the area of the right rear parcel shelf or right rear passenger seatback area while driving. ACTION 1. Widen the gap between two pieces of body paneling in the right side trunk area. 2. Fill the gap with expanding foam. Refer to SERVICE PROCEDURE in this bulletin for the repair procedure. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/7 SERVICE PROCEDURE NOTE: All pictures show repairs performed on a Maxima. The Altima is similar. CAUTION: Handle interior parts carefully to avoid damage. Work with clean hands and clean tools to avoid dirt and stains. IMPORTANT: Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS), such as an air bag. 1. Open the trunk. Figure 1 2. Remove the three (3) clips. Figure 2 2/7 NTB18-032a 3. Pull back the trunk mat and carpet. Carpet Figure 3 4. Recline forward the right rear passenger seatback. Clip 5. Remove the clip. Seatback Figure 4 6. Unfasten the ‘hook & loop’ fastener. Figure 5 3/7 NTB18-032a 7. Carefully peel back the trunk side finisher. Figure 6 4/7 NTB18-032a 8. Insert a plastic interior pry tool where shown in Figures 7 and 8, and then carefully widen the gap between the two body panels about 3/32 inch (3 mm). Make sure to insert the plastic interior pry tool at least 13/8 inches (35 mm) up into the gap, and then spread apart. CAUTION: Do NOT use a metal pry tool. It may puncture through the body panels. Use an interior plastic pry tool similar to the one shown on the next page, below PARTS INFORMATION. RH rear wheel housing Insert tool here Figure 7 9. Widen the gap and fill the area where shown in Figure 8 with expanding foam. See PARTS INFORMATION for recommended products. Spray the expanding foam into the gap just widened. Spread out and fill this area Insert tool in this gap at least 13/8 inches (35 mm) Figure 8 5/7 NTB18-032a 10. Wipe off any expanding foam that is not between the two body panels before it dries. 11. Reassemble the vehicle in reverse order of disassembly. 12. Test drive the vehicle, and verify the noise has stopped. PARTS INFORMATION DESCRIPTION PART NUMBER QUANTITY QUAD FOAM * -- 1 can ** * An equivalent 1-part polyurethane expanding foam product may be used. See EXPENSE CODE below. Available through retail and hardware stores. ** One can should repair multiple vehicles. Example of pry tool Figure 9 Figure 10 CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Adjust Body Panels (1) BX6NAA ZL 32 0.4 (1) Reference the Parts Information table above, and use the Rear Wheel House (G6700-*****) as the Primary Failed Part (PFP). EXPENSE CODE: EXPENSE CODE 563 DESCRIPTION Polyurethane Foam 6/7 MAX AMOUNT $2.40 NTB18-032a AMENDMENT HISTORY PUBLISHED DATE REFERENCE DESCRIPTION April 12, 2018 NTB18-032 Original bulletin published. February 19, 2019 NTB18-032a APPLIED VEHICLES, APPLIED VINS, and APPLIED DATES revised. 7/7 NTB18-032a