ITB19-011

Classification:
Reference:
Date:
BT19-007
ITB19-011
May 13, 2019
DEAD PEDAL REPLACEMENT
APPLIED VEHICLES:
2013 JX35 (L50)
2014 – 2019 QX60 (L50)
2014 – 2018 QX60 Hybrid (L50)
SERVICE INFORMATION
Dead pedal
If the dead pedal needs to be replaced for any
reason, it is no longer necessary to replace the front
floor trim (carpet).
The dead pedal is now available as a service part.
Figure 1
NOTE: Do not replace the carpet if only the dead pedal is needed.
ACTION
Follow the SERVICE PROCEDURE on the next page to replace ONLY the dead pedal.
NOTE: Dead pedal is listed in PARTS INFORMATION on the last page.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing.
You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to
successfully completing this repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that
a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this
applies to your vehicle.
1/6
SERVICE PROCEDURE
1.
Remove the driver side floor mat.
Kicking plate
Remove the driver side kicking plate.

LIFT
2.
Lift UP on the kicking plate to remove.
Figure 2
3.
Pull the driver side door welt away from the
body in the area indicated in Figure 3.
Figure 3
2/6
ITB19-011
4.
Remove the plastic screw from the kicking
plate support.

Pull the kicking plate support towards the
center of the vehicle to release 2 press-in
clips.
Kicking
Kick panel
plate
support clip
locations
Figure 4
Plastic screw
Figure 5
5.
Pull the upper left corner of the carpet down,
towards the driver seat.
Figure 6
3/6
ITB19-011
6.
Remove and discard the dead pedal, backing
plate, and press fit nuts.
Backing
plate
NOTE: These will be replaced with the NEW
parts listed in PARTS INFORMATION on the
last page.
Press fit
nuts
Figure 7
7.
Temporarily fold the carpet back to the original
position to locate the holes for the NEW dead
pedal.
8.
Position the NEW dead pedal into the holes in
the carpet.
Figure 8
9.
Fold the carpet back down towards the driver
seat.
10.
Place the backing plate onto the standoffs.
11.
Press the push nuts onto the dead pedal
standoffs.
Figure 9
NOTE: Using a 7 mm (1/4 inch) socket or
open end wrench will help assure the push
nuts are tight against the backing plate.
4/6
ITB19-011
12.
Fold the carpet back to its original location.
Figure 10
13.
Install all remaining components in the reverse order of removal.
5/6
ITB19-011
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
Dead Pedal Repair Kit
74901 - 9NJ5E
1
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Replace dead pedal
(1)
VX5LAA
(2)
(2)
0.2
(1) Reference the electronic parts catalog and use the Front Floor Carpet (74902-*****) as the Primary Failed
Part (PFP).
(2) Use the Symptom and Diagnostic codes that apply to the repair actually performed.
AMENDMENT HISTORY
PUBLISHED DATE
May 13, 2019
REFERENCE
ITB19-011
DESCRIPTION
Original bulletin published
6/6
ITB19-011