18N03-S7
Service Bulletin Details
Public Details for: 18N03-S7
Customer satisfaction program 18n03 - supplement #7 certain 2015-2018 model year f-150 and 2017-2018 model year f-250-f-550 vehicles - door latch freezing concerns
Models from 2018
2018 FORD F-150 |
2018 FORD F-250 SD |
2018 FORD F-350 SD |
2018 FORD F-450 SD |
2018 FORD F-550 SD |
Models from 2017
2017 FORD F-150 |
2017 FORD F-250 SD |
2017 FORD F-350 SD |
2017 FORD F-450 SD |
2017 FORD F-550 SD |
Models from 2016
2016 FORD F-150 |
Models from 2015
2015 FORD F-150 |
David J. Johnson Director Service Engineering Operations Ford Customer Service Division Ford Motor Company P. O. Box 1904 Dearborn, Michigan 48121 November 21, 2019 TO: All U.S. Ford and Lincoln Dealers SUBJECT: Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles - Door Latch Freezing Concerns REF: Customer Satisfaction Program 18N03 - Supplement #6 Dated April 23, 2019 NEW VEHICLE DEMONSTRATION / DELIVERY HOLD - Safety Recall 17S33 Certain 2015-2017 Model Year F-150 and 2017 Model Year F-Super Duty Vehicles Doors Will Not Close or Open While Driving REF: PROGRAM TERMS This is a one-time repair program for vehicle owners that report a door latch freezing concern. Affected vehicles are eligible for this repair through October 31, 2028, regardless of vehicle mileage or warranty start date. Coverage is automatically transferred to subsequent owners. This program will expire October 31, 2028. New! REASON FOR THIS SUPPLEMENT Technical Information: Updated with revised directions regarding the inspection of the interior door handle release cables. As a result, the Labor Allowances and the Parts Requirements / Ordering Information have also been updated. VEHICLES COVERED BY THIS PROGRAM Vehicle Model Year Assembly Plant F-150 2015-2018 F-250 - F-550 2017-2018 Build Dates Dearborn March 12, 2014 through April 12, 2018 Kansas City August 11, 2014 through April 3, 2018 Kentucky October 8, 2015 through April 21, 2018 OHAP February 5, 2016 through April 17, 2018 Affected vehicles are identified in OASIS. REASON FOR PROVIDING EXTENDED WARRANTY COVERAGE In the affected vehicles, water entering the doors in cold temperatures can cause door latching components to freeze. Ford is offering this no charge service to customers that have experienced a frozen door latch to install additional sealing to the front doors and crew cab rear doors, which will prevent water intrusion and door latch freezing. Copyright 2019 Ford Motor Company SERVICE ACTION If an affected vehicle owner has reported a frozen latch concern, dealers are to install additional sealing to the front doors and crew cab rear doors, lubricate certain door latch, door handle and cable components, clean the door drain holes, inject windshield wash concentrate or a methyl hydrate (methanol) product into the exterior door handle cables and install a wiper clip on the exterior door handle cable ends. This service must be performed at no charge to the vehicle owner. Note: The technical instructions for this program include all additional steps required to also complete safety recall 17S33, if 17S33 is open. OWNER NOTIFICATION MAILING SCHEDULE Owners of affected vehicles have been notified. Dealers should repair any affected vehicles that experience a frozen door latch whether or not the customer has received a letter. New! ATTACHMENTS Attachment I: Administrative Information Attachment II: Labor Allowances and Parts Ordering Information Attachment III: Technical Information Attachment IV: Instructional Video Links Attachment V: Door Glass Run Funnel Measurement Guide Owner Notification Letters QUESTIONS & ASSISTANCE For questions and assistance, contact the Special Service Support Center (SSSC) via the SSSC Web Contact Site. The SSSC Web Contact Site can be accessed through the Professional Technician Society (PTS) website using the SSSC link listed at the bottom of the OASIS VIN report screen or listed under the SSSC tab. Sincerely, David J. Johnson Copyright 2019 Ford Motor Company ATTACHMENT I Page 1 of 2 Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles Door Latch Freezing Concerns OASIS ACTIVATION OASIS was activated on September 26, 2018. FSA VIN LISTS ACTIVATION FSA VIN Lists was not activated for this service action. SOLD VEHICLES • Only owners with affected vehicles that exhibit the covered condition will be directed to dealers for repairs. • Dealers are to prioritize repairs of customer vehicles over repairs of new and used vehicle inventory. STOCK VEHICLES Do not perform this program unless the affected vehicle exhibits the covered condition. TITLE BRANDED / SALVAGED VEHICLES Affected title branded and salvaged vehicles are eligible for this service action. OWNER REFUNDS Refunds are not approved for this program. RENTAL VEHICLES The use of rental vehicles is not approved for this program. ADDITIONAL REPAIR (LABOR TIME AND/OR PARTS) Additional repairs identified as necessary to complete the FSA should be managed as follows: • For related damage and access time requirements, refer to the Warranty and Policy Manual – Section 6 – Ford & Lincoln Program Policies / General Information & Special Circumstances for FSA’s / Related Damage. • For vehicles within new vehicle bumper-to-bumper warranty coverage, no SSSC approval is required. o Ford vehicles - 3 years or 36,000 miles • For vehicles outside new vehicle bumper-to-bumper warranty coverage, submit an Approval Request to the SSSC Web Contact Site prior to completing the repair. Copyright 2019 Ford Motor Company ATTACHMENT I Page 2 of 2 Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles Door Latch Freezing Concerns CLAIMS PREPARATION AND SUBMISSION • Claim Entry: Enter claims using Dealer Management System (DMS) or One Warranty Solution (OWS) online. o When entering claims, select claim type 31: Field Service Action. The FSA number 18N03 is the sub code. o For additional claims preparation and submission information, refer to the Recall and Customer Satisfaction Program (CSP) Repairs in the OWS User Guide. • Related Damage/Additional labor and/or parts: Must be claimed as Related Damage on a separate repair line from the FSA with same claim type and sub code as described in Claim Entry above. IMPORTANT: Click the Related Damage Indicator radio button. • Provision for Locally Obtained Supplies: Includes XG-11, XG-13, XG-16, XL-6, TA-30, Cotton Swabs/Q-Tips®, Isopropyl Alcohol, brushes, syringe, eye dropper or a similar applicator and Motorcraft® Premium Windshield Wash Concentrate (ZC-32-B2) or a 99 percent Methyl Hydrate (Methanol) product. NOTE: The listed chemicals and locally obtained supplies can be used on multiple vehicles. o Program Code: 18N03 o Misc Expense: OTHER o Amount: Actual cost up to $12.00 • PROGRAM TERMS: This program will be in effect through October 31, 2028. There is no mileage limit for this program. • Claims with labor operation code 18N03B, 18N03C, 18N03D, 18N03E, 18N03F, 18N03G or 18N03H must have a repair date on or before January 8, 2019 to be eligible for payment. • Claims with labor operation code 18N03J, 18N03K, 18N03L, 18N03M, 18N03N, 18N03O or 18N03P must have a repair date on or before February 20, 2019 to be eligible for payment. • Claims with labor operation code 17S33F, 17S33G, 17S33H or 17S33J must have a repair date on or before April 23, 2019 to be eligible for payment. Copyright 2019 Ford Motor Company ATTACHMENT II Page 1 of 3 Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles Door Latch Freezing Concerns New! LABOR ALLOWANCES Only 18N03 open: Description Labor Operation Labor Time Install Front Door Latch Sealing (All Regular Cab) 18N03Q 2.0 Hours Install Front Door Latch Sealing (All Super Cab) 18N03R 2.0 Hours Install Front and Rear Door Latch Sealing (All Crew Cab) 18N03S 3.7 Hours Additional time to allow for obtaining the correct door glass run funnels, if a kit is found to be packaged with incorrect funnels. 18N03Z 0.1 Hours This labor operation can be used in combination with any 18N03 operations except MT18N03. * Additional Time For Replacement Of Interior Door Handle MT18N03 Release Cable(s) – Only if an interior door handle release cable 0.6 Hours Per Affected Door is found to be kinked. (Up To 2.4 Hours for 4 doors on This labor operation can be used in combination with any 18N03 a crew cab) operations except 18N03Z. * Less than 5% vehicles are expected to require a cable replacement. Both 18N03 and Safety Recall 17S33 open: NOTE: The following labor operations include incremental time for performing 18N03 when performing safety recall 17S33 is also required. Both 18N03 and 17S33 labor operations must be claimed on the same repair order, but separate repair order lines. NOTE: The 17S33 labor operation must be claimed using 17S33 as the sub code. Refer to the 17S33 dealer bulletin for complete 17S33 claiming instructions and part requirements. Description Labor Operation Install Front Door Latch Shields (F-150 Regular Cab)* 17S33K Install Front Door Latch Sealing (F-150 Regular Cab) 18N03T Claim both labor operations on separate repair lines Install Front and Rear Door Latch Shields (F-150 Super Cab)* 17S33M Install Front Door Latch Sealing (F-150 Super Cab) 18N03U Claim both labor operations on separate repair lines Install Front and Rear Door Latch Shields (F-150 Crew Cab)* 17S33L Install Front and Rear Door Latch Sealing (F-150 Crew Cab) 18N03V Claim both labor operations on separate repair lines Install Rear Door Latch Shields (F-250-F-550 Crew Cab)* 17S33N Install Front and Rear Door Latch Sealing (F-250-F-550 Crew Cab) 18N03W Claim both labor operations on separate repair lines * Includes time to replace lock rods and transfer buttons and grommets as needed. Labor Allowances Continued On The Next Page Copyright 2019 Ford Motor Company Labor Time 1.1 Hours 1.6 Hours 1.8 Hours 1.6 Hours 1.8 Hours 3.0 Hours 0.9 Hours 3.4 Hours ATTACHMENT II Page 2 of 3 Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles Door Latch Freezing Concerns New! LABOR ALLOWANCES (continued) Both 18N03 and Safety Recall 17S33 open: Description Labor Operation Labor Time ** Additional Time For Replacement Of Interior Door Handle MT18N03 Release Cable(s) – Only if an interior door handle release cable 0.6 Hours Per Affected Door (Up is found to be kinked. To 2.4 Hours for 4 doors on a This labor operation can be used in combination with any 18N03 crew cab) operations. ** Less than 5% vehicles are expected to require a cable replacement. New! PARTS REQUIREMENTS / ORDERING INFORMATION Part Number FL3Z-16308-L FL3Z-16308-P (New Kit)*** FL3Z-16308-M (Old Kit)*** FL3Z-16308-Q (New Kit)*** FL3Z-16308-N (Old Kit)*** LL3Z-15264B28-A Description Front Doors Foam Kit (F-150 Built Prior to December 2016*) Front Doors Foam Kit (F-150 Built December 2016 or later and All F-Super Duty*) Rear Doors Foam Kit (crew cab only) Exterior Door Handle Cable Wiper Clip (One Piece per Package) Order Quantity Claim Quantity As required As required As required 2 Req. Reg/Sup Cab 4 Req. Crew Cab XG-16 XG-13 XG-11 XL-6 TA-30 Motorcraft® Low Temperature Grease** Motorcraft® Door Latch Grease** Motorcraft® High Temperature Grease** Motorcraft® Silicone Spray** Motorcraft® Silicone Sealant** Motorcraft® Premium Windshield Wash MISC. OTHER ZC-32-B2 Concentrate, or a 99 percent Methyl Hydrate (Methanol) product** Cotton Swabs/Q-Tips®** Isopropyl Alcohol** Obtain Locally Brushes** Syringe, Eye Dropper or a Similar Applicator All parts are now available for open ordering. * Front door foam kit build date usages are approximations. ** The listed chemicals and locally obtained supplies can be used on multiple vehicles. *** Either kit can be used. The new kits have the correct funnels, and old kits require funnel verification. Parts Requirements / Ordering Information Continued On The Next Page Copyright 2019 Ford Motor Company ATTACHMENT II Page 3 of 3 Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles Door Latch Freezing Concerns New! PARTS REQUIREMENTS / ORDERING INFORMATION (continued) Part Number Description Order Quantity Claim Quantity HC3Z-15221A00-B (RH Front - All Vehicles Except F-150 with Gas Engine) HC3Z-15221A01-B (LH Front - All Vehicles Except F-150 with Gas Engine) FL3Z-15221A00-B (LH/RH Front - Only F-150 with Gas Engine) Interior Door Handle Release Cable As required **** FL3Z-1540180-A (LH/RH Rear - All Vehicles Crew Cab Doors) **** Less than 5% vehicles are expected to require a cable replacement. NOTE: Up to one of each of the “old” door foam kits can be claimed with each 18N03 repair, regardless of cab style and vehicle build date. If a door foam kit is found to have incorrect size door glass run funnels the correct size door glass run funnels can be removed from another kit, and that additional kit the door glass run funnels were removed from can be claimed with this repair. All unused parts of the additional kit can be scrapped. The “new” door foam kits always include the correct funnels, and therefore when “new” door foam kits are being used only the prescribed parts based on cab style and build date can be claimed. Order your parts requirements through normal order processing channels. To guarantee the shortest delivery time, an emergency order for parts must be placed. NOTE: Additional parts required to complete safety recall 17S33, if required, are listed in the 17S33 dealer bulletin. DEALER PRICE For latest prices, refer to DOES II. PARTS RETENTION AND RETURN Follow the provisions of the Warranty and Policy Manual, Section 1 - WARRANTY PARTS RETENTION AND RETURN POLICIES. EXCESS STOCK RETURN Excess stock returned for credit must have been purchased from Ford Customer Service Division in accordance with Policy Procedure Bulletin 4000. Copyright 2019 Ford Motor Company ATTACHMENT III PAGE 1 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 CERTAIN 2015-2018 MODEL YEAR F-150 AND 2017-2018 MODEL YEAR F-250 F-550 VEHICLES — DOOR LATCH FREEZING CONCERNS OVERVIEW In the affected vehicles, water entering the doors in cold temperatures can cause door latching components to freeze. Ford is offering this no charge service to customers that have experienced a frozen door latch to install additional sealing to the front doors and crew cab rear doors, which will prevent water intrusion and door latch freezing. If an affected vehicle owner has reported a frozen latch concern, dealers are to install additional sealing to the front doors and crew cab rear doors, and lubricate certain door latch, door handle and cable components. This service must be performed at no charge to the vehicle owner. NOTE: The technical instructions for this program include all additional steps required to also complete safety recall 17S33, if 17S33 is open. NOTE: Please read this procedure in its entirety, prior to performing repairs. Additionally, instructional videos have been developed to assist with the repair. Please refer to ATTACHMENT IV - Instructional Video Links to view the videos. NOTE: Some of the door foam kits were packaged with incorrect size door glass run funnels. Prior to starting the repair, please refer to ATTACHMENT V - Door Glass Run Funnel Measurement Guide, to ensure the correct funnels are being installed. SERVICE PROCEDURE Recommended Tool List: General Tools General Equipment 1/4" Drive Impact Driver Flashlight 1/4" Drive Ratchet Industrial Grade Heavy Duty Scissors 1/4" Drive Torque Wrench Bungee Cords 1/4" Drive Extension - 6" (152mm) Body Tape 1/4" Drive Socket - 7mm, 8mm and 10mm Q-Tips® 1/4" Driver Bit - T-20 and T-25 Torx® Brushes 3/8" Drive Ratchet Caulk Gun 3/8" Driver Bit - T-30 Torx® Ruler 3/8" Drive Torque Wrench Paint Pen Small Pick Locally Obtained Syringe, Eye Dropper or Similar Applicator Plastic Trim Removal Tools Disposable Gloves Pocket Screwdriver Shop Towel Blowgun Zip Tie Long Needle Nose Pliers Utility Knife 10mm Wrench Tape Measure CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 2 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Front Door Service Procedure 1. Is this a F-150 vehicle with safety recall 17S33 open? Yes - Proceed to the Front Door Latch Water Shield Kit installation Procedure. No - Proceed to the Front Door and Front Door Latch Sealing Procedure (Page 9). Front Door Latch Water Shield Kit Installation (Safety Recall 17S33 Open) NOTE: Front door latch water shields were phased into F-150 production in December 2016. For vehicles already equipped with water shields, it is not necessary to remove and replace the water shields on the front doors. NOTE: This procedure uses a different door latch water shield attachment procedure than what was previously used in TSB 16-0155. Do not attempt to use TSB parts to perform this procedure. NOTE: Procedure to be performed on both front doors. NOTE: The window must be in the closed (up) position when performing this procedure. NOTICE: Do not allow the door trim panel or exterior door handle to hang by the door handle cables or damage to the cable and door may occur. 1. Remove the exterior front door handles. Please follow the Workshop Manual (WSM) procedures in Section 501-14. NOTE: The interior grab handle cover clips can be reused for this repair. Only replace if damaged. 2. Remove the lock rod assemblies. See Figure 1. • Use the male end of a 1/4" extension to spread apart the lock rod retainer and remove the rod from the door latch. NOTE: Driver door latch shown, passenger door latch similar. 1737B FIGURE 1 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 3 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 3. Through the exterior front door handle opening, inspect for a rubber water shield installed on top of the door latch. See Figure 2. 4. If a rubber water shield is present, remove and discard the two attaching clips and the rubber water shield. 5. Clean the surface area where the water shield covered with isopropyl alcohol and a clean shop towel. Use part of the center portion of Foam E (refer to Figure 12) or some locally acquired body tape to seal the holes the attaching clips were previously installed in. See Figure 3. NOTE: Driver door latch shown, passenger door latch similar. DOOR LATCH ASSEMBLY FRONT OF VEHICLE FRONT OF VEHICLE RUBBER WATER SHIELD RUBBER WATER SHIELD DOOR LATCH ASSEMBLY 1737AL FIGURE 2 CLEAN THE HIGHLIGHTED AREA USE THE CENTER PORTION OF FOAM E OR FOAM K STUD FOR 1737DX MISSING NUT FIGURE 3 STUD FOR MISSING NUT STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 4 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 6. Remove and discard the rubber drain plug and clean any obstructions, debris, foreign material and residual water from all of the door drain holes using compressed air and a tool such as a plastic trim tool or a zip tie. See Figure 4. NOTE: Front passenger door shown, all doors similar. RUBBER DRAIN HOLE PLUG DOOR DRAIN HOLES 1903P FIGURE 4 7. Using compressed air, blow out any debris or residual water from the door latch assembly, exterior door handle mechanism and cables for thirty seconds. Blow drying with compressed air for thirty seconds is critical to remove as much moisture as possible. See Figure 5. NOTE: Driver front door latch shown, all door latches similar. BLOW OFF DOOR LATCH AREA FROM INTERIOR DOOR OPENING STUD FOR MISSING NUT STUD FOR MISSING NUT BLOW OFF DOOR LATCH AREA FROM DOOR HANDLE OPENING FIGURE 5 STUD FOR MISSING NUT 1737AN PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 5 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 8. Loosen but do not remove the two door glass run bolts. See Figure 6. E192718 FIGURE 6 9. Loosen but do not remove the 3 door latch bolts. See Figure 7. E192719 FIGURE 7 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 6 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 10. Apply supplied Foam Tape to the new water shield in the highlighted area. See Figure 8. 1737A FIGURE 8 11. With the latch and door glass run assembly loose inside the door panel, install the door latch water shield into position. See Figure 9. NOTE: The water shield is properly installed when the locating tabs align with the door glass run, the latch cable is fitted in the notch of the water shield, and the fastener holes align. 12. Install the new screw into the top hole of the shield. See Figure 9. NOTE: The lower fastener hole of the shield is not used on the front water shields. NOTE: Driver door latch shown, passenger door latch similar. LOCATING TAB STUD FOR MISSING NUT LATCH CABLE NOTCH LOCATING STUD FOR TAB MISSING NUT PLACE COPY HERE FRONT OF VEHICLE FRONT OF VEHICLE FIGURE 9 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE 1737D COPY HERE PLACE ATTACHMENT III PAGE 7 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 13. Tighten the two door glass run bolts. See Figure 6. • 8 Nm (71 lb.in). 14. Tighten the three door latch bolts. See Figure 7. • 8 Nm (71 lb.in). 15. Refer to Figure 10 to determine if the door latch is equipped with the new style lock rod. NOTE: The new style lock rod is required to accommodate the water shield. 16. Is the door latch equipped with the new style lock rod? Yes - Reinstall the lock rod and proceed to the Front Door and Front Door Latch Sealing Procedure (Page 9). No - Proceed to Step 17. OLD LOCK ROD 1737I NEW LOCK ROD FIGURE 10 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR ATTACHMENT III PAGE 8 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 NOTE: If a replacement lock rod already has a button and grommet installed, transfer of the components is not required. 17. Replace the lock rod and transfer the necessary components. See Figure 11. a. Transfer the grommet and button from the original lock rod to the new lock rod. b. Apply a bead of Motorcraft® Instant Gel Adhesive TA-19-C or equivalent to the lock rod prior to threading the button onto the new lock rod. c. When threading the button onto the new lock rod, stop threading when some resistance is met. d. Ensure both front lock rod buttons are installed at similar heights. e. Reinstall the lock rod. NOTE: Driver door latch shown, passenger door latch similar. BUTTON TO BE TRANSFERRED GROMMET TO BE TRANSFERRED AREA TO APPLY ADHESIVE 1737K FIGURE 11 18. Proceed to the Front Door and Front Door Latch Sealing Procedure. CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 9 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Front Door and Front Door Latch Sealing Procedure IMPORTANT! There are two different front door foam kits available for the F-150 vehicles. One kit comes with short (65mm funnel wings) door glass funnels (built before December 2016), and the other kit comes with long (157mm funnel wings) door glass funnels (built December 2016 or later). Funnel usage is based on vehicle build date and the length of the door glass run installed. Only one front door foam kit is available for the F-250-F-550 vehicles and the kit contains long (157mm funnel wings) door glass funnels. Refer to ATTACHMENT V for additional information. Complete Front Door Part Kit - Each Kit Will Include Either Long Door Glass Run Funnels Or Short Door Glass Run Funnels VEHICLES BUILT BEFORE DECEMBER 2016 SHORT DOOR GLASS RUN FUNNELS (65MM FUNNEL WINGS) FOAM H (DRIVER DOOR) FOAM F FOAM B (PASSENGER DOOR) FOAM G (DRIVER DOOR ONLY) VEHICLES BUILT DECEMBER 2016 OR LATER LONG DOOR GLASS RUN FUNNELS (157MM FUNNEL WINGS) FOAM C FOAM D FOAM TAPE RUBBER GROMMET (DRIVER DOOR ONLY) FOAM A FOAM E (ONLY THE THIN OUTER PORTION IS USED ON THE EXTERIOR DOOR HANDLES) 1737EA FIGURE 12 NOTE: The parts being installed in this procedure are not labeled. Refer to Figure 12 for component identification. NOTE: These components will be used for the following procedures: - Front Door Glass Run and Belt Moulding Sealing Procedure (All Vehicles) - Front Door Latch and Handle Service Procedure (All Vehicles) CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT ATTACHMENT III PAGE 10 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Front Door Glass Run and Belt Moulding Sealing Procedure (All Vehicles) Front Door Glass Run and Belt Moulding Sealing Components FOAM TAPE DOOR GLASS RUN FUNNELS (LONG FUNNELS SHOWN - 157MM FUNNEL WINGS) FOAM A 1737AQ FIGURE 13 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 11 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 NOTE: Procedure to be performed on both front doors. NOTE: The window must be in the closed (up) position when performing this procedure. NOTICE: Do not allow the door trim panel or exterior door handle to hang by the door handle cables or damage to the cable and door may occur. 1. Remove the exterior front door handles. Please follow the Workshop Manual (WSM) procedures in Section 501-14. NOTE: The interior grab handle cover clips can be reused for this repair. Only replace if damaged. 2. If a cable wiper clip is present on the exterior door handle cable end, remove and discard the cable wiper clip. See Figure 14. NOTE: Front passenger door shown, all doors similar. EXTERIOR DOOR HANDLE CABLE WIPER CLIP 1737AZ FIGURE 14 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 12 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 3. Inspect the interior door handle to latch release cable for kinking. See Figure 15. - Were any kinks visible on the interior door handle release cable? Yes - Continue to Step 4. No - Proceed to Step 6. CABLE TO BE INSPECTED 1737G FIGURE 15 NOTE: The front door latch of some vehicles is equipped with a small flexible plastic water shield located over the exterior door handle cable attachment point. Note the water shield position and orientation for reassembly. See Figure 16. NOTE: Certain vehicles are equipped with an interior door handle release cable retaining bracket on the front door latch. The interior door handle release cable is serviced in a similar manner whether or not a cable retaining bracket is present. See Figure 16. FRONT DOOR LATCH DOOR LATCH RIVETWATER SHIELD ATTACHMENT POINT INTERIOR DOOR HANDLE RELEASE CABLE RETAINING BRACKET STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT EXTERIOR DOOR PLACE COPY HERE HANDLE CABLE 1917JJ WATER SHIELD PLACE COPY HERE FIGURE 16 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 13 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 NOTE: It is not necessary to detach the exterior door handle cable from the retaining bracket or remove the exterior door handle cable from the latch. 4. Remove the front door latch and install a new interior door handle release cable. Please follow the WSM procedures in Section 501-14. CAUTION: Use caution not to kink the cables during reassembly of the door latch. NOTE: Do not reinstall the door panel, watershield or the exterior door handle at this time. 5. Reassemble and reinstall the front door latch. Complete by reversing the WSM procedures in Section 501-14. Then proceed to Step 6. CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 14 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 6. If water shield kit installation was not necessary, remove and discard the rubber drain plug and clean any obstructions, debris, foreign material and residual water from all of the door drain holes using compressed air and a tool such as a plastic trim tool or a zip tie. See Figure 17. NOTE: Front passenger door shown, all doors similar. RUBBER DRAIN HOLE PLUG DOOR DRAIN HOLES 1903P FIGURE 17 7. If not previously performed, use compressed air and blow out any debris or residual water from the door latch assembly, exterior door handle mechanism and cables for thirty seconds. Blow drying with compressed air for thirty seconds is critical to remove as much moisture as possible. See Figure 18. NOTE: Driver front door latch shown, all door latches similar. BLOW OFF DOOR LATCH AREA FROM INTERIOR DOOR OPENING STUD FOR MISSING NUT STUD FOR MISSING NUT BLOW OFF DOOR LATCH AREA FROM DOOR HANDLE OPENING FIGURE 18 STUD FOR MISSING NUT 1737AN PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 15 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 8. Position the front door window glass down. 9. Remove the inner belt moulding and position aside the latch side of the door glass top run. See Figure 19. 1737CF E192517 FIGURE 19 10. If present, remove and discard existing foam on the driver and passenger side outer belt moulding (also known as upper belt moulding) at this location. See Figure 20. NOTE: Passenger door shown, driver door similar. STUD FOR MISSING NUT STUD FOR MISSING NUT 1837CG FIGURE 20 STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 16 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 11. Clean the highlighted area of the outer belt moulding with isopropyl alcohol and a clean shop towel. See Figure 21. CLEAN BELT MOULDING CHANNEL FIRST CLIP LOCATION SECOND CLIP LOCATION 1737CH FIGURE 21 12. Apply a small bead of Motorcraft® TA-30 Silicone sealant onto the highlighted area of the outer belt moulding, ensuring the two belt moulding clips shown in Figures 21 and 22 are completely covered. Using your finger, smooth out the sealer to establish an even surface. See Figure 22. NOTE: A proper seal around the belt moulding metal clips is necessary to prevent water from entering the door. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT SECOND CLIP LOCATION FIRST CLIP LOCATION PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE 1737CI FIGURE 22 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 BELT MOULDING CLIP ATTACHMENT III PAGE 17 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 13. Using a small trim removal tool, install Foam A to the outer belt moulding on top of the bead of silicone that was previously applied. Both of the outer belt moulding clips need to be covered by the Foam A. See Figures 23 and 24. NOTE: It is crucial that both outer belt moulding clips are covered by Foam A and that the end of Foam A wraps around the outer belt moulding as shown. END OF FOAM A WRAPS AROUND HERE 1737CJ FIGURE 23 ENSURE FOAM A COVERS BOTH OUTER BELT MOULDING CLIPS END OF FOAM A WRAPS AROUND FOAM A 1737CK STUD FOR FIGURE 24 MISSING NUT 14. Remove any excessive silicone in visible areas on the outer belt moulding with isopropyl alcohol and STUD FOR a clean shop towel. MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE STUD FOR MISSING NUT ATTACHMENT III PAGE 18 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 15. Modify the front door glass top run. See Figure 25. a. b. c. Measure 15 mm (9/16 in) from the inboard bottom corner of the door glass top run. Mark the 15 mm (9/16 in) location. Starting at the bottom outboard corner of the door glass top run, cut a 45° notch using the previous measurement as a guide. B-PILLAR SIDE OF DOOR FRONT DOOR GLASS WINDOW RUN (B-PILLAR SIDE) CUT AT 45° USING 15 MM (9/16 IN) MEASUREMENT 15 MM (9/16 IN) FRONT DOOR GLASS WINDOW RUN 1737Z FIGURE 25 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 19 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 16. Install one of the appropriate length door glass run funnels ensuring that the lower tab is situated in the door glass run and the funnel sides sit at a 90° angle above the door glass run. See Figure 26. Refer to ATTACHMENT V for additional information. • F-150 vehicles: Short funnels - 65mm funnel wings (built before December 2016), Long funnels - 157mm funnel wings (built December 2016 or later) • F-250-F-550 vehicles: Long funnels only - 157mm funnel wings NOTE: Ensure the funnel sides are at a 90° angle upon installation. It may be necessary to bend the sides of the funnel back to a 90° angle before installation. ENSURE FUNNEL LEGS ARE BENT AT A 90° ANGLE DOOR GLASS RUN FUNNEL FUNNEL TAB IN DOOR GLASS RUN 1737AW FIGURE 26 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 20 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 17. Reinstall the latch side of the front door glass top run and the inner belt moulding. See Figure 19. NOTICE: When installing the rear door glass top run make sure not to bend or damage the door glass run funnel. Check through the exterior door handle opening to verify that the funnel is positioned correctly. 18. Unseat the front door lock rod grommet and visually confirm that the funnel is in the correct position and then reinstall the front door lock rod grommet. See Figure 27. NOTE: Driver door lock rod grommet shown, passenger door lock rod grommet similar. LOCK ROD GROMMET DOOR GLASS RUN FUNNEL DOOR GLASS RUN 1737DS FIGURE 27 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 21 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 19. Raise the front door window to the full up position. 3 2 20. Using your hand install the Foam Tape on the top of the door glass run and on the back of the door glass run funnel in the order shown in Figure 28. Figure 29 shows the Foam Tape installed. 1 1737CL FIGURE 28 NOTE: Front door shown, rear door similar. FOAM TAPE FUNNEL TAB IN DOOR GLASS RUN STUD FOR MISSING NUT DOOR GLASS L RUN FUNNEL STUD FOR MISSING NUT STUD FOR 1737CM MISSING NUT DOOR GLASS RUN FIGURE 29 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT ATTACHMENT III PAGE 22 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 21. Using isopropyl alcohol clean the top portion of the door and then neatly apply Motorcraft® TA-30 silicone sealant to the indicated/highlighted area in order to completely fill the gap as shown in Figure 30. • Do not close the door until the silicone is cured. NOTE: Proper application of the sealant is crucial to properly water seal the door and also avoid appearance concerns. NOTE: Top of driver front door shown, passenger front door similar. FRONT DOOR SEALANT APPLICATION COMPLETED APPLY SILICONE HERE 1737BI FIGURE 30 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 23 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 22. Modify the front door lock rod grommet. See Figure 31. a. b. Using a utility knife, cut four 6 mm (.25 in) long slits approximately 90° apart into the top of the front door lock rod grommet where the lock rod exits the grommet. Cut four additional 13 mm (.5 in) long slits approximately 90° apart on the inner sides of the grommet 45° separated from the previously cut slits. TOP VIEW SIDE VIEW 1737U FIGURE 31 23. Proceed to the Front Door Latch and Exterior Handle Service Procedure. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 24 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Front Door Latch and Exterior Handle Service Procedure (All Vehicles) NOTE: Procedure to be performed on both front doors. Front Door Latch and Exterior Handle Sealing Components FOAM H (DRIVER DOOR) FOAM B (PASSENGER DOOR) FOAM C FOAM C FOAM E (ONLY THE THIN OUTER PORTION IS USED ON THE EXTERIOR DOOR HANDLES) FOAM F FOAM D RUBBER GROMMET (DRIVER DOOR ONLY) FOAM G (DRIVER DOOR ONLY) 1737BJ FIGURE 32 1. For driver door latch only, attach Foam G to Foam H. See Figure 33. FOAM G (DRIVER DOOR ONLY) FOAM H STUD FOR MISSING NUT 1737BK CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 FIGURE 33 STUD FOR MISSING NUT ATTACHMENT III PAGE 25 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 2. Install Foam H onto the driver door latch. See Figure 34. NOTE: Driver door latch shown with Foam G and H, Passenger door latch similar with Foam B. FRONT OF VEHICLE FRONT OF VEHICLE DOOR LATCH ASSEMBLY FOAM H FOAM H FOAM G (DRIVER DOOR ONLY) DOOR LATCH ASSEMBLY EXTERIOR DOOR HANDLE OPENING 1737XX FIGURE 34 3. Install Foam D over the door latch cable and onto Foam H (driver door) and Foam B (passenger door) to cover the gap between the cable and Foam H. See Figure 35. • The notch of Foam D must point downwards when installed. NOTE: Driver door latch shown with Foam G and H, Passenger door latch similar with Foam B. FOAM D STUD FOR MISSING NUT FOAM H FOAM G (DRIVER DOOR ONLY) STUD FOR MISSING NUT NOTCH STUD FOR MISSING NUT PLACE COPY HERE 1737BL FIGURE 35 PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 26 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 4. Using a trim tool, install Foam C onto the top of the front door latch water shield. NOTE: For the taller style window runs refer to Figure 36a and for the shorter style window runs with a shoulder and a cable retaining clip refer to Figure 36b. NOTE: Driver door latch shown, passenger door latch similar. FRONT OF VEHICLE DOOR LATCH ASSEMBLY FRONT OF VEHICLE DOOR LATCH ASSEMBLY FOAM C FOAM C EXTERIOR DOOR HANDLE OPENING 1737YY FIGURE 36a EXTERIOR DOOR HANDLE OPENING DOOR LATCH ASSEMBLY FOAM C WINDOW RUN SHOULDER WITH CABLE RETAINING CLIP FRONT OF VEHICLE FOAM C DOOR LATCH ASSEMBLY FRONT OF VEHICLE FIGURE 36b STUD FOR MISSING NUT 1737GD STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT ATTACHMENT III PAGE 27 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 5. Using a trim tool, install Foam F between the water shield and the door glass run. See Figure 37. NOTE: Do not remove the adhesive backing from Foam F and install Foam F with the adhesive backing facing downward. NOTE: Driver door shown, passenger door similar. DOOR GLASS RUN FOAM F WATER SHIELD ADHESIVE BACKING 1737BM FIGURE 37 6. For driver side only, apply Motorcraft® XG-13 grease to the area where the key lock rod attaches to the key lock rod lever. See Figure 38. 7. For driver side only, install the rubber grommet onto the key lock rod over the key lock rod lever. The rubber grommet should be positioned as shown. The rubber grommet will sit sideways when installed properly. See Figure 38. NOTE: Door latch assembly shown out of vehicle for clarity. KEY LOCK ROD RUBBER GROMMET PLACE RUBBER GROMMET AGAINST KEY LOCK ROD STUD FOR MISSING NUT STUD FOR MISSING NUT APPLY XG-13 GREASE HERE DO NOT PLACE RUBBER GROMMET IN THISSTUD AREA FOR MISSING NUT PLACE COPY HERE KEY LOCK ROD LEVER CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 FIGURE 38 PLACE COPY HERE 1737BN PLACE COPY HERE ATTACHMENT III PAGE 28 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 8. Apply XG-11 grease on top of and around Foam D after Foam D is installed. The Foam D notch, the gap between the cable and Foam D, and the gap between the door glass run and Foam H must be covered with grease. See Figure 39. NOTE: Do not allow the XG-11 grease to come into contact with moving components of the latch mechanism. NOTE: Driver door shown, passenger door similar. APPLY XG-11 GREASE FOAM D FOAM H NOTCH FOAM G (DRIVER DOOR ONLY) 1737CN FIGURE 39 9. If equipped, disconnect the interior door handle cable retaining clips from the door sheet metal. 10. Using isopropyl alcohol and a clean shop towel, throughly remove grease from the interior door handle cable mechanism. See Figure 40. REMOVE GREASE INTERIOR DOOR HANDLE CABLE STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING 1737AK NUT FIGURE 40 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 29 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 11. Unseat the interior door handle cable rubber grommet and while holding the end of the cable in an upward position, spray Motorcraft® XL-6 Lubricant down into the cable for five seconds. See Figure 41. NOTE: If the Motorcraft® XL-6 Lubricant container is not equipped with an applicator nozzle that can accommodate a straw, swap the applicator nozzle from another Motorcraft® chemical such as: XL-5 Multi-Purpose Grease Spray, XL-5-A Multi-Purpose Grease Spray or ZC-30-A Silicone Gasket Remover so a straw can be used. Spray a small amount to clear the applicator nozzle and straw prior to spraying the cable. INTERIOR DOOR HANDLE CABLE UNSEAT RUBBER GROMMET 1737ED FIGURE 41 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT ATTACHMENT III PAGE 30 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 12. Using a bungee cord or other similar device, secure the interior door handle cable to the door in an upward position to allow the Motorcraft® XL-6 Lubricant time to run down into the cable, until the interior door handle cable is reinstalled later in this procedure. See Figure 42. BUNGEE CORD INTERIOR DOOR HANDLE CABLE 1737DK FIGURE 42 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 31 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 NOTE: The use of disposable gloves is required. 13. Towel dry the exterior door handle cable to absorb any residual moisture. Using a bungee cord or other similar device secure the exterior door handle cable to the door in an upward position as shown in Figure 43, to allow the undiluted Motorcraft® Premium Windshield Wash Concentrate (ZC-32-B2) or a 99 percent methyl hydrate (methanol) product time to run down into the cable, until the exterior door handle cable is reinstalled later in this procedure. 14. Using a locally obtained syringe, eye dropper or a similar applicator draw 10 ml of the undiluted Motorcraft® ZC-32-B2 Concentrate or a 99 percent methyl hydrate (methanol) product into the applicator. With the cable pulled out and the tip of the applicator positioned inside the arrowhead cable end fitting inject 2 ml between the cable shield and the cable then cycle the cable 5 times in and out of the cable shield. Repeat injecting fluid and cycling the cable a total of 5 times. NOTICE: Place a shop towel around the exterior door handle cable, while performing this procedure, to prevent dripping onto the vehicle which could cause paint damage. NOTE: Do not use a product that contains isopropyl alcohol. Only use a product containing methanol or a mix of methanol and ethylene glycol. NOTE: Rear door shown, front door similar. APPLICATOR EXTERIOR DOOR HANDLE CABLE BUNGEE CORD EXTERIOR DOOR HANDLE OPENING FIGURE 43 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 1737ZZ ATTACHMENT III PAGE 32 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 15. Using a clean shop towel and isopropyl alcohol, clean the highlighted mating surface area of the exterior front door handle. See Figure 44. 1737V FIGURE 44 16. Using a clean shop towel and isopropyl alcohol clean inside the dotted lines on the mating surface area of the front exterior door handle openings. See Figure 45. 1737CO FIGURE 45 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR ATTACHMENT III PAGE 33 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 17. Install Foam E around the perimeter of the exterior door handle on top of the existing seal. NOTE: Foam E will not wrap around the entire perimeter of the exterior door handle. NOTE: Proper placement of Foam E is crucial for proper sealing and to avoid appearance concerns. A. Lay out Foam E on the exterior door handle and mark center as shown in Figure 46. B. Remove Foam E from the door handle and remove the back center portion of the adhesive backing then cut the protective backing in half. See Figure 46. C. Align the marks made on the Foam E and exterior door handle and adhere the back center portion to the exterior door handle as shown in Figure 47. D. Lay one side of Foam E down on the exterior door handle and without stretching the foam pull off the adhesive backing as you adhere Foam E to the exterior door handle as shown in Figure 47. E. Remove the protective backing from the other side of Foam E as shown in Figure 47. F. Without stretching the foam adhere it to the exterior door handle ensuring that both sides of Foam E are of equal length once secured. See Figure 48. A B FOAM E MARK THE HANDLE AND FOAM E HERE FOAM E CUT PROTECTIVE BACKING HERE BACK CENTER 1737DL FIGURE 46 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 34 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 C D E 1737DM FIGURE 47 F FOAM E EQUAL LENGTHS FIGURE 48 STUD 1737DB FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT ATTACHMENT III PAGE 35 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 18. Using a clean shop towel and isopropyl alcohol, clean the handle plunger then using a brush apply a light film of Motorcraft® XG-16 low temperature grease to all four sides of the exterior door handle plunger and to the mechanisms in the areas shown in Figures 49 and 50. APPLY A LIGHT FILM OF XG-16 GREASE HERE (ALL FOUR SIDES) 1737BP FIGURE 49 APPLY A LIGHT FILM OF XG-16 GREASE HERE FIGURE 50 1737BO STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT ATTACHMENT III PAGE 36 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 19. Apply a bead of Motorcraft® TA-30 silicone sealant to the latch side area of the front door exterior handle opening making sure that the sealant will overlap with the Foam E on the exterior door handle. See Figure 51. NOTE: Proper placement of the Motorcraft® TA-30 silicone sealant is crucial for proper sealing and to avoid appearance concerns. NOTE: Driver door shown, passenger door similar. MOTORCRAFT® TA-30 SILICONE SEALANT FOAM E SEALANT NEEDS TO OVERLAP FOAM E HERE FRONT OF VEHICLE 1737CS FIGURE 51 20. Remove the bungee cords used to hold the interior and exterior door handle cables up, seat the rubber grommet and if equipped, reinstall the interior door handle cable retaining clips. 21. Reconnect the exterior door handle cable to the door handle, then lubricate the door handle cable end with Motorcraft® XG-16 low temperature grease, as shown in Figure 52. APPLY XG-16 GREASE HERE STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE 1737DI FIGURE 52 PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 37 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 22. Install a new handle cable wiper clip on the exterior door handle cable end. See Figure 53. FULLY SEATED EXTERIOR DOOR HANDLE CABLE WIPER CLIP ORIENTATION 1903M FIGURE 53 23. Reinstall the front exterior door handles. Please follow the WSM procedures in Section 501-14. NOTICE: Reinstall the exterior door handle cable and retaining clips in the original factory position. 24. Clean any excessive silicone around the exterior door handle perimeter with isopropyl alcohol, Q-tips® and a clean shop towel to avoid appearance concerns. 25. Determine next steps based on vehicle and cab configuration. • • • For all Regular Cab vehicles, F-150 Super Cab vehicles without safety recall 17S33 open, and all F-250-F-550 Super Cab vehicles, the repair is complete. For all Crew Cab vehicles, proceed to the Rear Door Service Procedure (Page 38). For F-150 Super Cab vehicles with safety recall 17S33 open, proceed to the Rear DoorSTUD LowerFOR Latch Water Shield Kit Installation Procedure (Page 69). MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 38 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Rear Door Service Procedure (Crew Cab Vehicles) 1. Is safety recall 17S33 open? Yes - Proceed to the Rear Door Latch Water Shield Kit Installation Procedure (Crew Cab Vehicles). No - Proceed to the Rear Door Glass Run and Belt Moulding Sealing Procedure (Crew Cab Vehicles). (Page 42) Rear Door Latch Water Shield Kit Installation Procedure (Crew Cab Vehicles With Safety Recall 17S33 Open) NOTE: This procedure uses a different door latch water shield attachment procedure than what was previously used in TSB 16-0155. Do not attempt to use TSB parts to perform this procedure. NOTE: Procedure to be performed on both rear doors. NOTE: The window must be in the closed (up) position when performing this procedure. NOTICE: Do not allow the door trim panel or exterior door handle to hang by the door handle cables or damage to the cable and door may occur. 1. Remove the exterior rear door handles. Please follow the WSM procedures in Section 501-14. NOTE: The interior grab handle cover clips can be reused for this repair. Only replace if damaged. 2. Remove the lock rod assembly from the rear door latch. See Figure 54. • Use the male end of a 1/4" extension to spread apart the lock rod retainer and remove the rod from the door latch. NOTE: Driver door latch shown, passenger door latch similar. 1737C FIGURE 54 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 39 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 3. Remove and discard the rubber drain plug and clean any obstructions, debris, foreign material and residual water from all of the door drain holes using compressed air and a tool such as a plastic trim tool or a zip tie. See Figure 55. NOTE: Front passenger door shown, all doors similar. RUBBER DRAIN HOLE PLUG DOOR DRAIN HOLES 1903P FIGURE 55 4. Using compressed air, blow out any debris or residual water from the door latch assembly, exterior door handle mechanism and cables for thirty seconds. Blow drying with compressed air for thirty seconds is critical to remove as much moisture as possible. See Figure 56. NOTE: Driver front door latch shown, all door latches similar. BLOW OFF DOOR LATCH AREA FROM INTERIOR DOOR OPENING STUD FOR MISSING NUT STUD FOR MISSING NUT BLOW OFF DOOR LATCH AREA FROM DOOR HANDLE OPENING FIGURE 56 STUD FOR MISSING NUT 1737AN HERE PLACE COPY PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 40 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 5. Install the door latch water shield into position. See Figure 57. NOTE: The water shield is properly installed when the latch cable is fitted in the notch of the water shield and the fastener holes align. 6. Install the new screws into the top and bottom holes of the shield. See Figure 57. NOTE: Driver door latch shown, passenger door latch similar. FRONT OF VEHICLE FRONT OF VEHICLE 1737E FIGURE 57 7. Refer to Figure 58 to determine if the door latch is equipped with the new style lock rod. Is the door latch equipped with the new style lock rod or manual locks? Yes - Reinstall the lock rod if equipped and proceed to the Rear Door Glass Run and Belt Moulding Sealing Procedure (Page 42). No - Proceed to Step 8. OLD STYLE LOCK ROD STUD FOR MISSING NUT NEW STYLE LOCK ROD CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 FIGURE 58 1737N PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 41 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 8. Lock rod replacement procedure. See Figure 59. NOTE: If a replacement lock rod already has a button and grommet installed, transfer of the components is not required. a. b. c. d. e. Transfer the grommet, sleeve and button from the original lock rod to the new lock rod. Apply a bead of Motorcraft® Instant Gel Adhesive TA-19-C or equivalent to the lock rod prior to threading the button onto the new lock rod. When threading the button onto the new lock rod, stop threading when some resistance is met. Ensure both rear lock rod buttons are installed at similar heights. Reinstall the lock rod. NOTE: Driver door latch shown, passenger door latch similar. BUTTON TO BE TRANSFERRED GROMMET TO BE TRANSFERRED AREA TO APPLY ADHESIVE 1737DO FIGURE 59 9. Proceed to the Rear Door Glass Run and Belt Moulding Sealing Procedure (Page 42). STUD FOR MISSING NUT STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 42 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Rear Door Glass Run and Belt Moulding Sealing Procedure (Crew Cab Vehicles) Complete Rear Door Part Kit FOAM H DRIVER SIDE FOAM J DOOR GLASS RUN FUNNELS (132MM FUNNEL WINGS) PASSENGER SIDE FOAM J FOAM K FOAM I FOAM L FOAM N FOAM TAPE 1 FOAM TAPE 2 1737BR FIGURE 60 NOTE: The parts being installed in this procedure are not labeled. Refer to Figure 60 for component identification. STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 43 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Rear Door Glass Run and Belt Moulding Sealing Components NOTE: Procedure to be performed on both rear doors. FOAM H FOAM N 1737DP FIGURE 61 NOTE: Procedure to be performed on both rear doors. NOTE: The window must be in the closed (up) position when performing this procedure. NOTICE: Do not allow the door trim panel or exterior door handle to hang by the door handle cables or damage to the cable and door may occur. 1. Remove the exterior rear door handles. Please follow the Workshop Manual (WSM) procedures in Section 501-14. NOTE: The interior grab handle cover clips can be reused for this repair. Only replace if damaged. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 44 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 2. If a cable wiper clip is present on the exterior door handle cable end, remove and discard the cable wiper clip. See Figure 62. NOTE: Front exterior door handle shown, all exterior door handles similar. EXTERIOR DOOR HANDLE CABLE WIPER CLIP 1737AZ FIGURE 62 3. Inspect the interior door handle to latch release cable for kinking. See Figure 63. - Were any kinks visible on the interior door handle release cable? Yes - Proceed to Step 4. No - Proceed to Step 6. CABLE TO BE INSPECTED STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE 1737L PLACE COPY HERE FIGURE 63 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 45 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 NOTE: It is not necessary to detach the exterior door handle cable from the retaining bracket or remove the exterior door handle cable from the latch. 4. Remove the rear door latch and install a new interior door handle release cable. Please follow the WSM procedures in Section 501-14. CAUTION: Use caution not to kink the cables during reassembly of the door latch. NOTE: Do not reinstall the door panel, watershield or the exterior door handle at this time. 5. Reassemble and reinstall the rear door latch. Complete by reversing the WSM procedures in Section 501-14. Then proceed to Step 6. 6. If water shield kit installation was not necessary, remove and discard the rubber drain plug and clean any obstructions, debris, foreign material and residual water from all of the door drain holes using compressed air and a tool such as a plastic trim tool or a zip tie. See Figure 64. NOTE: Front passenger door shown, all doors similar. RUBBER DRAIN HOLE PLUG DOOR DRAIN HOLES 1903P FIGURE 64 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT ATTACHMENT III PAGE 46 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 7. If not previously performed, use compressed air and blow out any debris or residual water from the door latch assembly, exterior door handle mechanism and cables for thirty seconds. Blow drying with compressed air for thirty seconds is critical to remove as much moisture as possible. See Figure 65. NOTE: Driver front door latch shown, all door latches similar. BLOW OFF DOOR LATCH AREA FROM INTERIOR DOOR OPENING BLOW OFF DOOR LATCH AREA FROM DOOR HANDLE OPENING 1737AN FIGURE 65 8. Position the rear door window glass down. 9. Remove the rear door inner belt moulding and position aside the latch side of the door glass top run. See Figure 66. REAR DOOR GLASS TOP RUN INNER BELT MOULDING STUD FOR MISSING NUT STUD FOR MISSING NUT 1737AF FIGURE 66 STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 47 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 10. If present, remove and discard the foam on the door outer belt moulding at the location shown in Figure 67. 1737CT FIGURE 67 11. Clean the highlighted area of the outer belt moulding with isopropyl alcohol and a clean shop towel. See Figure 68. NOTE: Make sure to clean past the second clip. SECOND CLIP LOCATION FIRST CLIP LOCATION STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT 1737CU PLACE COPY HERE FIGURE 68 PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 48 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 12. Apply Motorcraft® TA-30 silicone sealer to the area highlighted on the outer belt moulding. Using your finger, smooth out the sealer to establish an even surface. See Figures 69 and 70. NOTE: Completely covering the belt moulding metal clips is crucial for proper sealing. See Figure 70. 1737CV FIGURE 69 FIRST CLIP LOCATION SECOND CLIP LOCATION STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT 1737CW FIGURE 70 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 49 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 13. Install Foam H to the C-pillar end of the outer belt moulding. See Figure 71. FOAM H 1737JB FIGURE 71 STUD FOR MISSING NUT STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 50 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 14. Remove any excessive silicone in visible areas on the outer belt moulding with isopropyl alcohol and a clean shop towel. 15. Modify the rear door glass top run. See Figure 72. a. Measure 15 mm (9/16 in) from the inboard bottom corner of the door glass top run. b. Starting at the bottom outboard corner of the rear door glass top run, cut a 45° notch using the previous measurement as a guide. C-PILLAR SIDE OF DOOR REAR DOOR GLASS WINDOW RUN (C-PILLAR SIDE) CUT AT 45° USING 15 MM (9/16 IN) MEASUREMENT REAR DOOR GLASS WINDOW RUN 15 MM (9/16 IN) 1737BY FIGURE 72 16. If present, remove and discard the felt on the rear door glass top run. See Figure 73. REMOVE FELT IF PRESENT STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT 1737DC PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 FIGURE 73 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 51 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 17. Clean the highlighted area of the rear door glass top run with isopropyl alcohol and a clean shop towel. See Figure 74. C-PILLAR NOTCH REAR DOOR GLASS TOP RUN CLEAN HIGHLIGHTED AREA 1737BZ FIGURE 74 18. Install Foam N to the highlighted area of rear door glass top run making sure that the Foam N is under the C-Pillar notch. See Figure 75. a b C-PILLAR NOTCH FOAM H FOAM N STUD FOR FOAM H AND FOAM N MISSING NUT MUST COVER THE GAP AT THIS LOCATION FOAM N STUD FOR MISSING NUT STUD FOR MISSING NUT 1737DG FIGURE 75 PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 52 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 19. With the rear door latch side door glass top run still positioned aside raise the rear door window glass three quarters of the way up. See Figure 76. NOTICE: Use care when raising window glass to not pinch door glass top run or scratch the glass. 1737CP FIGURE 76 20. Modify the rear door lock rod grommet. See Figure 77. a. b. c. d. Remove the rear door lock rod grommet from the lock rod. Cut approximately 6 mm (0.25 in)off the top of the grommet. Install the rear door lock rod grommet back onto the lock rod. Using a utility knife, cut four 6 mm (0.25 in) long slits approximately 90° apart into the lower portion of the rear door lock rod grommet. d b STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT CUT 6mm (0.25in) FROM THE TOP PLACE COPY HERE CUT FOUR SLITS 1737UA FIGURE 77 21. Proceed to the Rear Door Latch and Handle Service Procedure. CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 53 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Rear Door Latch and Handle Service Procedure (Crew Cab Vehicles) Rear Door Latch and Handle Sealing Components NOTE: Procedure to be performed on both rear doors. FOAM I FOAM TAPE 1 DOOR GLASS RUN FUNNELS (132MM FUNNEL WINGS) FOAM L FOAM TAPE 2 FOAM K FOAM J FOAM J (ONLY THE THIN OUTER PORTION IS (PASSENGER DOOR) USED ON THE EXTERIOR DOOR HANDLES) (DRIVER DOOR) FIGURE 78 1. Install Foam J onto the rear door latch. See Figure 79. 1737DV FOAM K NOTE: Driver door latch shown, passenger door latch similar. FRONT OF VEHICLE FRONT OF VEHICLE FOAM J FOAM J STUD FOR MISSING NUT DOOR LATCH ASSEMBLY EXTERIOR DOOR HANDLE OPENING DOOR LATCH ASSEMBLY FIGURE 79 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT 1737AB STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 54 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 2. Install Foam L over the door latch cable and onto Foam J to cover the gap between the exterior door latch cable and Foam J. See Figure 80. • The notch of foam L must point downward when installed. NOTE: Driver door latch shown, passenger door latch similar. FOAM J EXTERIOR DOOR LATCH CABLE FOAM L NOTCH 1737DW FIGURE 80 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 55 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 3. Clean the highlighted area on top of the door latch water shield with isopropyl alcohol and a clean shop towel where the Foam Tape 2 will be installed. See Figure 81. NOTE: Driver door latch shown, passenger door latch similar. FOAM TAPE 2 FRONT OF VEHICLE DOOR LATCH ASSEMBLY FOAM TAPE 2 DOOR LATCH ASSEMBLY EXTERIOR DOOR HANDLE OPENING 1737AC FIGURE 81 4. Install Foam Tape 2 on top of the rear door latch water shield. See Figures 82. • Make sure that Foam Tape 2 attaches to the water shield and to the door glass run. NOTE: Driver door latch shown, passenger door latch similar. FOAM TAPE 2 MUST ATTACH TO THE GLASS RUN AREA TO BE SEALED BY FOAM TAPE 2 STUD FOR MISSING NUT STUD FOR MISSING NUT FIGURE 82 STUD FOR 1737DR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 56 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 5. Install Foam I to cover the gap between the rear door latch assembly water shield and the door glass run. See Figure 83. NOTE: Driver door latch shown, passenger door latch similar. FRONT OF VEHICLE DOOR LATCH ASSEMBLY FOAM I FOAM I EXTERIOR DOOR HANDLE OPENING DOOR LATCH ASSEMBLY 1737AD FIGURE 83 6. Apply Motorcraft® TA-30 silicone sealant in and over the mating area of the water shields to the door. Using light finger pressure smooth the bead of silicone. See Figure 84. APPLY TA-30 SILICONE SEALANT TO DOOR LATCH WATER SHEILD HIGHLIGHTED AREA STUD FOR MISSING NUT DOOR LATCH WATER SHEILD STUD FOR MISSING NUT STUD1737JA FOR MISSING NUT FIGURE 84 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 57 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 7. Position the rear door window glass down. 8. Install the door glass run funnel (132mm funnel wings), ensuring the lower tab is situated in the door glass run and the funnel sides sit at a 90° angle above the door glass run. Refer to ATTACHMENT V for additional information. See Figure 85. NOTE: Verify the sides of the funnel are bent to 90° prior to installation. 90° ANGLE DOOR GLASS RUN FUNNEL DOOR GLASS RUN FUNNEL FUNNEL TAB IN DOOR GLASS RUN FUNNEL TAB IN DOOR GLASS RUN 1737CA FIGURE 85 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 58 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 9. Install the rear door glass top run and inner belt moulding. See Figure 66. NOTICE: When installing the rear door glass top run make sure not to bend or damage the door glass run funnel. Check through the exterior door handle opening to verify that the funnel is positioned correctly. 10. Position the rear door window glass up. 11. Apply supplied Foam Tape 1 in the location shown to hold the funnel in place. See Figure 86. FOAM TAPE 1 FUNNEL TAB IN DOOR GLASS RUN 1903I FIGURE 86 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 59 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 12. Apply XG-11 grease on top of and around Foam L. The Foam L notch, the gap around the cable and Foam L, and the gap between the door latch assembly and Foam J must be filled with grease. See Figure 87. NOTE: Do not allow the XG-11 grease to come into contact with moving components of the latch mechanism. AREA TO APPLY XG-11 GREASE FOAM L 1737CQ FIGURE 87 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 60 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 13. Using isopropyl alcohol and a clean shop towel, throughly remove grease from the interior door handle cable mechanism. See Figure 88. REMOVE GREASE INTERIOR DOOR HANDLE CABLE 1737AK FIGURE 88 14. Unseat the interior door handle cable rubber grommet and while holding the end of the interior door handle cable in an upward position, spray Motorcraft® XL-6 Lubricant for five seconds down into the cable. See Figure 89. NOTE: If the Motorcraft® XL-6 Lubricant container is not equipped with an applicator nozzle that can accommodate a straw, swap the applicator nozzle from another Motorcraft® chemical such as: XL-5 Multi-Purpose Grease Spray, XL-5-A Multi-Purpose Grease Spray or ZC-30-A Silicone Gasket Remover so a straw can be used. Spray a small amount to clear the applicator nozzle and straw prior to spraying the cable. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE UNSEAT THE CABLE GROMMET PLACE COPY HERE INTERIOR DOOR HANDLE CABLE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 FIGURE 89 1737EB ATTACHMENT III PAGE 61 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 15. Using a bungee cord or other similar device, secure the interior door handle cable to the door in an upward position to allow the lubricant time to run down into the cable, until the interior door handle cable is reinstalled later in this procedure. See Figure 90. BUNGEE CORD INTERIOR DOOR HANDLE CABLE 1737EC FIGURE 90 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 62 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 NOTE: The use of disposable gloves is required. 16. Towel dry the exterior door handle cable to absorb any residual moisture. Using a bungee cord or other similar device secure the exterior door handle cable to the door in an upward position as shown in Figure 91, to allow the undiluted Motorcraft® Premium Windshield Wash Concentrate (ZC-32-B2) or a 99 percent methyl hydrate (methanol) product time to run down into the cable, until the exterior door handle cable is reinstalled later in this procedure. 17. Using a locally obtained syringe, eye dropper or a similar applicator draw 10 ml of the undiluted Motorcraft® ZC-32-B2 Concentrate or a 99 percent methyl hydrate (methanol) product into the applicator. With the cable pulled out and the tip of the applicator positioned inside the arrowhead cable end fitting inject 2 ml between the cable shield and the cable then cycle the cable 5 times in and out of the cable shield. Repeat injecting fluid and cycling the cable a total of 5 times. NOTICE: Place a shop towel around the exterior door handle cable, while performing this procedure, to prevent dripping onto the vehicle which could cause paint damage. NOTE: Do not use a product that contains isopropyl alcohol. Only use a product containing methanol or a mix of methanol and ethylene glycol. APPLICATOR EXTERIOR DOOR HANDLE CABLE BUNGEE CORD EXTERIOR DOOR HANDLE OPENING FIGURE 91 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 1737ZZ ATTACHMENT III PAGE 63 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 18. Using a clean shop towel and isopropyl alcohol, clean the highlighted mating surface area of the exterior door handle. See Figure 92. 1737DD FIGURE 92 19. Using a clean shop towel and isopropyl alcohol, clean inside the dotted lines on the mating surface area of the exterior door handle opening. See Figure 93. STUD FOR MISSING NUT FIGURE 93 STUD FOR 1737CR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR ATTACHMENT III PAGE 64 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 20. Install Foam K around the perimeter of the exterior door handle on top of the existing seal. NOTE: Foam K will not wrap around the entire perimeter of the exterior door handle. NOTE: Proper placement of Foam K is crucial for proper sealing and to avoid appearance concerns. A. Lay out Foam K on the exterior door handle and mark center as shown in Figure 94. B. Remove Foam K from the door handle and remove the back center portion of the adhesive backing then cut the protective backing in half. See Figure 94. C. Align the marks made on the Foam K and exterior door handle and adhere the back center portion to the exterior door handle as shown in Figure 95. D. Lay one side of Foam K down on the exterior door handle and without stretching the foam pull off the adhesive backing as you adhere Foam K to the exterior door handle as shown in Figure 95. E. Remove the protective backing from the other side leg of Foam K as shown in Figure 95. F. Without stretching the foam adhere it to the exterior door handle ensuring that both sides of Foam K are of equal length once secured. See Figure 96. A B FOAM K MARK THE HANDLE AND FOAM K HERE FOAM K CUT PROTECTIVE BACKING HERE BACK CENTER 1737EE FIGURE 94 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 65 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 C D E 1737DM FIGURE 95 F FOAM K EQUAL LENGTHS FIGURE 96 STUD 1737EFFOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT ATTACHMENT III PAGE 66 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 21. Using a clean shop towel and isopropyl alcohol, clean the handle plunger then, using a brush, apply a light film of Motorcraft® XG-16 low temperature grease to all four sides of the exterior door handle plunger and to the mechanisms in the areas shown in Figures 97 and 98. APPLY A LIGHT FILM OF XG-16 GREASE HERE (ALL FOUR SIDES) 1737BP FIGURE 97 APPLY A LIGHT FILM OF XG-16 GREASE HERE FIGURE 98 1737DF STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE ATTACHMENT III PAGE 67 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 22. Apply a bead of Motorcraft® TA-30 silicone sealant to the rear vertical area of the rear door metal surface making sure that the sealant will overlap with the Foam K on the exterior door handle. See Figure 99. NOTE: Proper placement of the Motorcraft® TA-30 silicone sealant is crucial to ensure proper sealing and avoid appearance concerns. NOTE: Driver door shown, passenger door similar. MOTORCRAFT® TA-30 SILICONE SEALANT FOAM K SEALANT NEEDS TO OVERLAP FOAM K HERE FRONT OF VEHICLE 1737CX FIGURE 99 STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 PLACE COPY HERE ATTACHMENT III PAGE 68 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 23. Remove the bungee cords used to hold the interior and exterior door handle cables up and seat the interior door handle cable rubber grommet. 24. Reconnect the exterior door handle cable to the door handle, then lubricate the door handle cable end with XG-16 low temperature grease as shown in Figure 100. APPLY XG-16 GREASE HERE 1737ES FIGURE 100 25. Install a new handle cable wiper clip on the exterior door handle cable end. See Figure 101. FULLY SEATED EXTERIOR DOOR HANDLE CABLE WIPER CLIP ORIENTATION STUD FOR MISSING NUT STUD FOR 1903MNUT MISSING FIGURE 101 STUD FOR MISSING NUT 26. Reinstall the rear exterior door handles. Please follow the WSM procedures in Section 501-14. PLACE COPY HERE NOTICE: Reinstall the exterior door handle cable and retaining clips in the original factory position. PLACE COPY HERE 27. Clean any excessive silicone around the exterior door handle perimeter with isopropyl alcohol, PLACEQ-tips COPY HERE and a clean shop towel to avoid appearance concerns. Crew Cab vehicle repair is complete. CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT ATTACHMENT III PAGE 69 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 Rear Door Lower Latch Water Shield Kit Installation (F-150 Super Cab Vehicles With Safety Recall 17S33 Open) NOTE: If the vehicle has previously had a rear lower door latch replaced, it may already have the latest level door latch water shield installed. If the Super Cab rear lower door latch has a large water shield installed as shown in Figure 106, then installation of a new water shield is not required. NOTE: Procedure to be performed on both rear doors. 1. Remove the rear door interior trim panels. Please follow the WSM procedures in Section 501-05. 2. Remove the door panel weather shield for access. See Figure 102. 3. Using compressed air, blow out any debris or residual water from the latch assembly area. See Figure 102. BLOW OFF DOOR LATCH FROM INTERIOR DOOR OPENING 1903O FIGURE 102 STUD FOR MISSING NUT CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 STUD FOR MISSING NUT STUD FOR MISSING NUT ATTACHMENT III PAGE 70 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 4. Inspect the interior door handle to latch cable for kinking. See Figure 104. • Correct any kinks found in the cable by straightening the cable by hand as required. 5. Remove the three lower door latch bolts. See Figure 103. E194857 FIGURE 103 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 71 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 6. Detach the cable retainers and disconnect the electrical connector. Position the rear door latch outside of the door. See Figure 104. E194848 FIGURE 104 NOTE: Some F-150 SuperCab vehicles may be equipped with a smaller water shield than what is being installed in this program. The smaller shields must be removed and replaced. See Figure 105. 7. If equipped with small water shields, remove and discard the existing lower door latch water shields. See Figure 105. 1737H FIGURE 105 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT III PAGE 72 OF 72 CUSTOMER SATISFACTION PROGRAM 18N03-S7 8. Install a new door latch water shield onto the lower rear door latch. See Figure 106. 1737F FIGURE 106 9. Position the rear door lower latch back into the door. Attach the cable retainers and connect the electrical connector. See Figure 104. 10. Install the three lower door latch bolts. See Figure 103. • Torque 12 Nm (106 lb.in). 11. Install the door panel weather shields. See Figure 102. 12. Install the rear door interior trim panels. Please follow the WSM procedures in Section 501-05. Super Cab vehicle repair is complete. STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 ATTACHMENT IV Page 1 of 1 Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles - Door Latch Freezing Concerns INSTRUCTIONAL VIDEO LINKS Video Links: F-150 shown, F-250-F-550 is similar. IMPORTANT: Always refer to the dealer bulletin and the technical information for latest parts requirements and repair procedures. NOTE: The procedures below are listed in the order they are shown in the technical information (Attachment III). NOTE: Some videos show the same procedure performed on a vehicle as well as on a bench for demonstration purposes. NOTE: The color of the grease used in the videos below may not reflect the color of the grease being used in the actual repair, as the required grease has been changed from XG-13 to XG-16 in most locations. Video 1: Front Door Latch Water Shield Kit Installation - All F-150 Vehicles, If 17S33 Open Video 2: Front Door Latch Rubber Water Shield Removal And Rubber Water Shield Retaining Pin Holes Sealing Procedure - All F-150 Vehicles, If Rubber Water Shield Present Video 3: Front Door Glass Top Run And Outer Belt Moulding Sealing Procedure Video 4: Door Glass Run Funnel And Door Glass Top Run Installation Procedure - Rear Door Shown, Front Door Similar Video 5: Front Door Latch Sealing Procedure Video 6: Exterior Door Handle Sealing Procedure - Rear Door Shown, Front Door Similar Video 7: Rear Door Latch Water Shield Kit Installation - Crew Cab Vehicles, If 17S33 Open Video 8: Rear Door Glass Top Run and Outer Belt Moulding Sealing Procedure Video 9: Rear Door Latch Sealing Procedure Video 10: Rear Door Lower Latch Water Shield Kit Installation - F-150 Super Cab Vehicles, If 17S33 Open Copyright 2019 Ford Motor Company ATTACHMENT V PAGE 1 OF 1 CUSTOMER SATISFACTION PROGRAM 18N03-S7 CERTAIN 2015-2018 MODEL YEAR F-150 AND 2017-2018 MODEL YEAR F-250 F-550 VEHICLES — DOOR LATCH FREEZING CONCERNS OVERVIEW Some of the door foam kits were packaged with incorrect size door glass run funnels. Dealers are to measure the door glass run funnel wings using the measurement guide below. If a door foam kit is found to have incorrect size door glass run funnels the correct size door glass run funnels can be removed from another kit, and that additional kit the door glass run funnels were removed from can also be claimed with this repair. All unused parts from the additional kit can be scrapped. NOTE: This packaging error caused rear doors foam kit FL3Z-16308-N to be incorrectly packaged with door glass run funnels from front doors foam kits FL3Z-16308-M. Conversely, the front doors foam kits FL3Z-16308-M were also incorrectly packaged with door glass run funnels from rear doors foam kit FL3Z-16308-N. If foam kits FL3Z-16308-M or FL3Z-16308-N are found to have incorrect funnels the correct funnels can likely be found in the other kit. NOTE: This packaging error was corrected in December 2018. SERVICE PROCEDURE - Door Glass Run Funnel Measurement Guide Recommended Tool List: General Tools Tape Measure 1. Verify the correct door glass funnels are being installed by measuring the funnel wings as shown in Figure 1. NOTE: FunnelComparison modification is not of Funnel Kits advised. FL3Z-16308-M FRONT DOORS FOAMFront KIT FL34-16308-M Door Kit Post Dec’16 F-150 BUILT DECEMBER 2016forOR F150 and all Super Duty. LATER AND ALL F-SUPER DUTY Funnel wings should (157MM LONG FUNNEL WINGS) measure 157mm long FL3Z-16308-N FL34-16308-N Rear Door Kit For FOAM All Rear Door Crew REAR DOORS KIT Cabs. Funnel Wings should CREW CAB VEHICLES ONLY measure 132mm long (132MM LONG FUNNEL WINGS) FL3Z-16308-M Front Door FL3Z-16308-L Kit For F150 Pre Dec’16. FunnelFOAM Wings should FRONT DOORS KITbe 65mm long F-150 BUILT PRIOR TO DECEMBER 2016 (65MM LONG FUNNEL WINGS) FUNNEL WING FIGURE 1 CPR © 2019 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 11/2019 1737ER