LTB01208NAS4

1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
LT B 0 1 2 0 8 N A S 4
TECHNICAL BULLETIN
02âJAN 2020
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly
and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should
not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a
condition described affects your vehicle. Contact an authorized Land Rover service facility
to determine whether this bulletin applies to a specific vehicle.
I N F O R M AT I O N
This reissue replaces all previous versions. Please destroy all previous versions.
This bulletin supersedes TSB LTB01208NAS3/2019 dated 10bJAN 2019, which should
either be destroyed or clearly marked to show it is no longer valid (e.g. with a line across
the page). Only refer to the electronic version of this Technical Bulletin in TOPIx.
SECTION:
501-14
S U B J E C T/ C O N C E R N :
Hood Release Inoperative
AFFECTED VEHICLE RANGE:
MODEL:
Discovery (LR)
MODEL YEAR:
2017-2018
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
VIN:
000004-077150
1/7
1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
The hood release lever is not releasing the hood.
CAUSE:
Incorrect length of hood release cable.
ACTION:
Follow the instructions below.
PA RTS :
PART NUMBER
LR121817
DESCRIPTION
QUANTITY
Hood release cable
1
WARRANT Y:
NOTES:
Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Use TOPIx to obtain
the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
DESCRIPTION
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
Hood release cable - Renew
76.16.89.01
0.5
42
LR083194
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
2/7
1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
NOTE:
Normal Warranty procedures apply.
SERVICE INSTRUCTION:
NOTES:
Some variation in the illustrations may occur, but the essential information is
always correct.
Some components are shown removed for clarity.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
3/7
1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
1.

Open the hood and use a steel rule or similar engineer's scale to record the
distance the interior release lever travels to operate the hood latches.
If the hood interior release lever does operate the hood latches,
the hood can be opened, and the distance is less than 120mm,
release the vehicle.
No further action required.
If the hood interior release lever does operate the hood latches,
the hood can be opened, and the distance is more than 120mm,
go to Step 5.
If the hood interior release lever does not operate the hood
latches and the hood cannot be opened, go to Step 2.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
4/7
1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
2.

Remove hood interior release lever from the hood release mechanism.
3.

Release the hood release cable from the hood release mechanism.
4.
Use a suitable tool to operate the hood release cable to open the hood latches.
5.
Remove the hood left and right latches (see TOPIx Workshop Manual section
501-14: Handles, Locks, Latches and Entry Systems - Removal and Installation Hood Latch).
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
5/7
1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
6.

Release the hood release cable.
7.

Remove the trim.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
6/7
1/2/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
8.

Release the hood release cable from the retainer.
9.

Remove the hood release cable from the vehicle.
10.
To install the new hood release cable, reverse steps 1 to 9.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1576834187512
7/7