JTB00662NAS2
Service Bulletin Details
Public Details for: JTB00662NAS2
A transmission fluid leak may be seen coming from below the vehicle. There may also be a lack of acceleration and/or a 'juddering' from the vehicle while driving. A transmission warning message may also be displayed on the instrument panel
Models from 2020
2020 JAGUAR F-PACE |
Models from 2019
2019 JAGUAR F-PACE |
Models from 2018
2018 JAGUAR F-PACE |
Models from 2017
2017 JAGUAR F-PACE |
5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 JTB00662NAS2 TECHNICAL BULLETIN 06 MAY 2020 © Jaguar Land Rover North America, LLC NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle. INFORMATION This reissue replaces all previous versions. Please destroy all previous versions. Changes are highlighted in blue SECTION: 307-02 SUBJECT/CONCERN: Transmission Fluid Cooler Pipes - Fluid Leak AFFECTED VEHICLE RANGE: MODEL: F-PACE (X761) MODEL YEAR: 2017 Onwards VIN: APPLICABILITY: 045145 Onwards INGENIUM I4 2.0L Petrol/INGENIUM I4 2.0L Diesel MARKETS: https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 1/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 NORTH AMERICA CONDITION SUMMARY: NOTES: This technical bulletin is only applicable to All Wheel Drive (AWD) vehicles. This technical bulletin is only applicable to vehicles installed with automatic transmissions. SITUATION: A transmission fluid leak may be seen coming from below the vehicle. There may also be a lack of acceleration and/or a 'juddering' from the vehicle while driving. A transmission warning message may also be displayed on the Instrument Panel Cluster (IPC). Upon further diagnosis, the fluid may be found leaking from the transmission fluid cooler pipe(s). CAUSE: Excessive vibration transmitted through the transmission fluid cooler pipes while the engine is running, causing the weld joints to fracture. ACTION: Follow the instruction(s) below. PARTS: PART NUMBER DESCRIPTION QUANTITY T4A29688 Transmission fluid cooler pipes - With bracket assembly installed - Ingenium I4 2.0L Diesel 1 T4A11794 Transmission fluid cooler pipes - Ingenium I4 2.0L Petrol 1 T4A33742 Bracket - Ingenium I4 2.0L Petrol 1 T4A33743 Bracket clip - Ingenium I4 2.0L Petrol 1 JDE2798 Bracket bolt 1 T2H9243 Front driveshaft bolts 4 JDE26444 Transmission fluid (1 Liter) 1 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 2/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 PART NUMBER JDE36540 DESCRIPTION QUANTITY Transmission oil plug service kit 1 WARRANTY: NOTES: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Use TOPIx to obtain the latest repair time. The JLR claims submission system requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero. SRO TIME (HOURS) CONDITION CODE CAUSAL PART JTB - Transmission Fluid Cooler Pipes - Inspect No further action 99.01.05 0.5 01 T4A15334 / T4A11794 Transmission Fluid Cooler Pipes - Renew Ingenium I4 2.0L Diesel 44.24.19 1.1 01 T4A15334 / T4A11794 Transmission Fluid Cooler Pipes - Renew Ingenium I4 2.0L Petrol 44.24.19 1.2 01 T4A15334 / T4A11794 Transmission fluid level inspect - Top up if required 44.24.06 1.0 01 T4A15334 / T4A11794 DESCRIPTION NOTE: Normal Warranty procedures apply. SERVICE INFORMATION: Ingenium I4 2.0L Petrol vehicles only https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 3/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 1. The illustration shows how to install the bracket to the bracket clip as shown. Ingenium I4 2.0L Diesel vehicles only 2. Remove the bracket from the NEW Transmission fluid cooler pipes (T4A29688). SERVICE INSTRUCTION: https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 4/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 NOTE: Some components are shown removed to provide extra clarity. 1. Raise and support the vehicle on a ramp, (see TOPIx workshop manual section 10002: Description and Operation - Lifting). 2. NOTE: The undershield may also be known to as an air deflector within the workshop manual. Remove the engine undershield to visually inspect the condition of the transmission fluid cooler pipes, (see TOPIx workshop manual section 501-02: Removal and installation - Engine Undershield). If the transmission fluid cooler pipes do show signs of leaking, continue to step 3. If the transmission fluid cooler pipes do not show signs of leaking, do not continue with this technical bulletin. Raise a Technical Assistance (TA) for further assistance. 3. Remove the front driveshaft, (see TOPIx workshop manual section 205-01: Removal and Installation - Front Driveshaft). https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 5/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 4. CAUTION: Be prepared to collect escaping fluids. Release the transmission fluid cooler pipes. 5. Remove the bolt securing the transmission fluid cooler pipes to the oil pan. https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 6/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 6. CAUTION: The transmission fluid cooler assembly must remain supported at all times. Release the transmission fluid cooler assembly from the front subframe. https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 7/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 7. CAUTION: The transmission fluid cooler assembly must remain supported at all times. Remove and discard the transmission fluid cooler pipes. https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 8/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 8. CAUTION: The transmission fluid cooler assembly must remain supported at all times. Install the new transmission fluid cooler pipes to the transmission fluid cooler. 9. Install the transmission fluid cooler assembly to the front subframe. Torque: 9 Nm. https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 9/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 10. Install the bolt securing the transmission fluid cooler pipes to the oil pan. Torque: 11 Nm. 11. Install the transmission fluid cooler pipes. Torque: 22 Nm. https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 10/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 12. The illustration shows the location required for installing the bracket in the following step. Ingenium I4 2.0L Diesel vehicles https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 11/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 13. Install the bracket using the following method: 1 - Position the bracket clip over the transmission fluid cooler pipes in the position shown. 2 - Make sure the bolt hole in the bracket aligns with the threaded bolt hole in the transmission. 3 - Close the bracket clip. 4 - Install the bolt. Torque: 22 Nm. Ingenium I4 2.0L Petrol vehicles https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 12/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 14. Install the bracket using the following method: 1 - Position the bracket clip over the transmission fluid cooler pipes in the position shown. 2 - Make sure the bolt hole in the bracket aligns with the threaded bolt hole in the transmission. 3 - Close the bracket clip. 4 - Install the bolt. Torque: 22 Nm. 15. Install the front driveshaft, (see TOPIx workshop manual section 205-01: Removal and Installation - Front Driveshaft). 16. Inspect the transmission fluid level, top up if required, (see TOPIx workshop manual section 307-01: General Procedures - Transmission Fluid Level Inspect). 17. NOTE: The 'engine undershield' is also known as an 'air deflector' within the TOPIx Workshop Manual. Install the engine undershield, (see TOPIx workshop manual section 501-02: Removal and installation - Engine Undershield). https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 13/14 5/6/2020 https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 18. Lower the vehicle, (see TOPIx workshop manual section 100-02: Description and Operation - Lifting). https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1584714779839 14/14