NTB18-033b

Classification:
Reference:
FE17-001b
Date:
NTB18-033b
July 7, 2020
ACCELERATOR PEDAL VIBRATION
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
2014-2020 Rogue (T32)
This bulletin does not apply to Rogue Hybrid.
IF YOU CONFIRM
A vibration from the accelerator pedal between 1600 - 2000 RPM.
ACTION
Install the new brake booster vacuum tube and hose listed in the PARTS INFORMATION
section of this bulletin.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/6
SERVICE PROCEDURE
1.
Loosen the air duct assembly (aft)
screw clamps.
2.
Separate the rubber air duct
assembly (aft) from the mass air flow
sensor and the electronic throttle
control actuator.
Electronic
throttle
control
actuator
Air duct assembly
(aft) screw clamps
Air duct
assembly (aft)
Mass air
flow sensor
Figure 1
3.
Release the EVAP test port hose
from the clip.
4.
Release the breather hose clamp
from the air duct assembly (aft).
5.
Remove the breather hose from the
air duct assembly (aft).
EVAP test port
hose clip
Breather
hose
clamp
Breather hose
Figure 2
Air duct assembly (aft) clip locations
6.
Pull the air duct assembly (aft)
straight up on the passenger side
then the driver side to release the
clips.
7.
Remove the air duct assembly (aft)
from the vehicle.
Figure 3
2/6
NTB18-033b
8.
Remove the acoustic absorber clips from the cowl.
NOTE:

There are two (2) different possible acoustic absorber designs.

The clips are located in the approximate area shown in Figure 4 and Figure 5.
Design 1
Design 2
Acoustic absorber
clip location
Acoustic absorber
clip locations
Acoustic absorber
Figure 5
Figure 4
9.
Release the clamp from the brake
booster vacuum hose at the intake
manifold.
10.
Remove the brake booster vacuum
hose from the intake manifold.
Clamp
Brake booster
vacuum hose
Figure 6
3/6
NTB18-033b
11.
Release the clamp from the brake
booster vacuum hose at the brake
booster.
12.
Remove the brake booster vacuum
hose from the brake booster.
Brake booster
vacuum hose
Clamp
Figure 7
13.
Release the two (2) brake booster
vacuum tube mounting clips.
NOTE: The passenger side mounting
clip is located under the acoustic
absorber in the approximate location
shown in Figure 8.
Mounting clip
locations
14.
Remove the brake booster vacuum
tube from the vehicle.
Figure 8
NOTE:

Old brake booster vacuum tube and hose
The new brake booster vacuum tube
will come with a new rubber hose for
the brake booster side.

The original rubber hose on the
intake manifold side will need to
be transferred to the new metal
brake booster vacuum tube.

All original hose clamps will need to
be transferred to the new brake
booster vacuum tube.
Intake
manifold side
New brake booster vacuum tube and hose
Figure 9
4/6
NTB18-033b
15.
Locate the plastic sleeve installed on
the metal section of the new brake
booster vacuum tube.
NOTE: The old brake booster
vacuum tube is not equipped with the
plastic sleeve. The plastic sleeve will
be used in the next step to properly
locate the new brake booster vacuum
line.
Plastic sleeve
Figure 10
Driver side clip
16.
Install the new brake booster vacuum
tube.
17.
Attach the driver side clip to the new
brake booster vacuum tube with the
plastic sleeve positioned on the driver
side of the clip.
Plastic sleeve
Brake
booster
Figure 11
18.
Reinstall all other components in the reverse order of removal.
5/6
NTB18-033b
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
TUBE-VAC BRAKE BOOSTER
47401 - 7FA0A
1
HOSE-VAC BRAKE BOOSTER
47471 - 7FA0A
1
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Replace Brake Booster
(1)
PF14AA
(2)
(2)
(3)
Vacuum Tube/Hose
(1) Reference the Parts Information table above, and use the TUBE-VAC BRAKE
BOOSTER as the Primary Failed Part (PFP).
(2) Use the Symptom and Diagnostic codes that apply to the repair actually performed.
(3) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.
AMENDMENT HISTORY
PUBLISHED DATE
REFERENCE
DESCRIPTION
April 18, 2018
NTB18-033
Original bulletin published
November 28, 2018
NTB18-033a
APPLIED VEHICLES section revised
July 7, 2020
NTB13-033b
Added 2020 model year to APPLIED
VEHICLES
6/6
NTB18-033b