T-SB-0158-18 Rev

T-SB-0158-18
Rev2
December 14, 2018
Floor Mat Installation During PDS
Service
Category
General
Section
Pre-Delivery Service
Market USA
Applicability
YEAR(S)
MODEL(S)
2020
4Runner, 86, Avalon, Avalon
HV, C-HR, Camry, Camry
HV, Corolla, Corolla
Hatchback, Corolla HV,
Highlander, Highlander HV,
Land Cruiser, Mirai, Prius,
Prius C, Prius Prime, RAV4,
RAV4 HV, Sequoia, Sienna,
Supra, Tacoma, Tundra,
Yaris SD MEX-Prod
ADDITIONAL INFORMATION
REVISION NOTICE
October 09, 2020 Rev2:
• Installation Procedure: Pre-Installed Knob Style section has been updated.
July 03, 2019 Rev1:
• Applicability has been updated to include 2020 model year Supra vehicles.
• The Hook and Loop Style section has been added.
Any previous printed versions of this bulletin should be discarded.
Introduction
2020 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the
floor mat in the correct position. In addition, some models may also utilize retainers for passenger
side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation
Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats
to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor
mat kit, place the instructions in the vehicle’s glove box for customer reference.
© 2020 Toyota Motor Sales, USA
Page 1 of 16
T-SB-0158-18
Rev2
December 14, 2018
Page 2 of 16
Floor Mat Installation During PDS
Introduction (continued)
CAUTION
• ALWAYS verify the floor mat is designed specifically for the model and model year it is being
installed in.
• ONLY use floor mats that can be secured using the retainers. ALL OEM Toyota floor mats are
specifically designed to fit correctly and be secured using the retainers.
• Make sure the floor mat is properly placed on the vehicle carpet and secured with the
retainers. If the driver side floor mat is NOT properly placed and secured, it could slip and
interfere with the movement of the pedals during driving and may cause an accident.
• Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance to
the mat.
• NEVER install more than one floor mat at a time in the driver’s seating position.
• If applicable, ANY secondary set of floor mats (based upon customer preference, such as the
all-weather floor mats or other floor mats) MUST be placed in the trunk with ALL the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver’s seating position.
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
–
–
–
–
Installation Procedures
•
Hook Style ............................................................................................................................... 3
•
Hook Style With Locking Clip ................................................................................................... 5
•
Knob Style With Locking Clip ................................................................................................... 8
•
Pre-Installed Knob Style ......................................................................................................... 12
•
Pre-Installed Post Style........................................................................................................... 15
•
Hook and Loop Style .............................................................................................................. 16
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 3 of 16
Floor Mat Installation During PDS
Installation Procedure: Hook Style
1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for the
correct model and model year they are being installed in.
2. Attach the driver side, and if applicable, passenger side, and rear seat floor mats to the vehicle
carpet using the retention clips.
3. Secure the mat by inserting the retention clip hooks through the grommet holes.
Figure 1.
3
1
1
2
2
3
1
Correct Installation
2
Retention Clip
3
© 2020 Toyota Motor Sales, USA
Grommet
T-SB-0158-18
Rev2
December 14, 2018
Page 4 of 16
Floor Mat Installation During PDS
Installation Procedure: Hook Style (continued)
4. Verify proper installation.
NOTE
If applicable, do NOT remove the beige caution tag from the floor mat. ONLY the customer should
remove the caution tag.
Figure 2.
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 5 of 16
Floor Mat Installation During PDS
Installation Procedure: Hook Style With Locking Clip
1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for the
correct model and model year they are being installed in.
2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.
1
B
5
B
4
A
A
B
3
2
1
Retention Clip
5
Cross-sectional Diagram
2
Front of Vehicle
A
Retention Clip Claw
3
Retention Clip Eyelet on Vehicle Floor
B
Locking Clip
4
Seat
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 6 of 16
Floor Mat Installation During PDS
Installation Procedure: Hook Style With Locking Clip (continued)
3. To lock the retention clip in place, insert the
locking clip of the retention clip into the
designated hole.
Figure 4.
1
1
4. Align the floor mat grommets with the
retention clip hooks and attach the floor mat
grommets to the retention clip hooks.
Locking Clip
Figure 5.
1
2
3
1
Floor Mat Grommet
2
Retention Clip
3
Front
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 7 of 16
Floor Mat Installation During PDS
Installation Procedure: Hook Style With Locking Clip (continued)
5. Verify proper installation.
NOTE
If applicable, do NOT remove the beige caution tag from the floor mat. ONLY the customer should
remove the caution tag.
Figure 6.
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 8 of 16
Floor Mat Installation During PDS
Installation Procedure: Knob Style With Locking Clip
1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for
the correct model and model year they are being installed in.
2. Attach the retention clip to the floor by
inserting the retention clip claw into the
floor eyelet.
Figure 7.
1
B
3
A
4
2
B
A
1
Retention Clip
2
Retention Clip Eyelet on Vehicle Floor
3
Seat
4
Front of Vehicle
A
Retention Clip Claw
B
Locking Clip
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 9 of 16
Floor Mat Installation During PDS
Installation Procedure: Knob Style With Locking Clip (continued)
3. To lock the clip in place, insert the locking
clip of the retention clip into the
designated hole.
Figure 8.
1
1
4. Align the floor mat grommets with the
retention clip knobs and place the floor mat
grommets onto the retention clip knobs.
Locking Clip
Figure 9.
1
2
3
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front of Vehicle
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 10 of 16
Floor Mat Installation During PDS
Installation Procedure: Knob Style With Locking Clip (continued)
5. Twist the retention clip knobs a quarter of a
turn to lock in place.
Figure 10.
3
6. Verify the triangle marks on the retention clip
knob and floor mat are aligned.
1
1
Twist Knob
2
Knob in Locked Position
3
Align Triangle Marks
© 2020 Toyota Motor Sales, USA
2
T-SB-0158-18
Rev2
December 14, 2018
Floor Mat Installation During PDS
Installation Procedure: Knob Style With Locking Clip (continued)
7. Verify proper installation.
Figure 11.
NOTE
If applicable, do NOT remove the yellow
caution tag from the floor mat. ONLY the
customer should remove the caution tag.
© 2020 Toyota Motor Sales, USA
Page 11 of 16
T-SB-0158-18
Rev2
December 14, 2018
Page 12 of 16
Floor Mat Installation During PDS
Installation Procedure: Pre-Installed Knob Style
NOTICE
If the vehicle is equipped with two sets of floor mats (carpet and all weather):
• Do NOT install both sets of floor mats at the same time.
• Install one set according to the current season and store the other set in the
luggage compartment.
• Discard the Floor Mat Safety Check insert for the installed set and keep the other with the spare
floor mat set for the customer’s reference.
1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for the
correct model and model year vehicle they are being installed in.
2. Align the floor mat grommets with the
retention knobs and place the floor mat
grommets onto the retention knobs.
Figure 12.
1
2
3
1
Floor Mat Grommet
2
Retention Knob
3
Front of Vehicle
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 13 of 16
Floor Mat Installation During PDS
Installation Procedure: Pre-Installed Knob Style (continued)
3. Twist the retention knobs a quarter of a turn
to lock in place.
Figure 13.
3
4. Verify the triangle marks on the retention
knobs and floor mat are aligned.
1
1
Twist Knob
2
Knob in Locked Position
3
Align Triangle Marks
© 2020 Toyota Motor Sales, USA
2
T-SB-0158-18
Rev2
December 14, 2018
Floor Mat Installation During PDS
Installation Procedure: Pre-Installed Knob Style (continued)
5. Verify proper installation.
Figure 14.
NOTE
If applicable, do NOT remove the yellow
caution tag from the floor mat.
ONLY the customer should remove the
caution tag.
© 2020 Toyota Motor Sales, USA
Page 14 of 16
T-SB-0158-18
Rev2
December 14, 2018
Page 15 of 16
Floor Mat Installation During PDS
Installation Procedure: Pre-Installed Post Style
1. Verify that the driver side, and if applicable, passenger side, and rear seat floor mats are for
the correct model and model year vehicle they are being installed in.
2. Align the floor mat grommets with the
retention posts and press the floor grommets
onto the retention posts until you hear and
feel a click.
Figure 15.
3
2
1
1
Floor Mat Grommet
2
Retention Post
3
Front of Vehicle
3. Verify proper installation.
NOTE
Following installation, the floor mat grommets should be flush with the retention posts.
© 2020 Toyota Motor Sales, USA
T-SB-0158-18
Rev2
December 14, 2018
Page 16 of 16
Floor Mat Installation During PDS
Installation Procedure: Hook and Loop Style
1. Verify that the driver side, and, if applicable, passenger side floor mats are for the correct
model and model year vehicle they are being installed in.
2. Attach the driver, and if applicable,
passenger side floor mats to the vehicle
carpet using the hook and loop fasteners.
Figure 16.
1
c
2
3
1
Underside of Driver Floor Mat
2
Loop
3
Hook
3. Verify proper installation.
© 2020 Toyota Motor Sales, USA