JTB00544NAS2

12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
JTB00544NAS2
TECHNICAL BULLETIN
16 DEC 2020
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly and
safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not
be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition
described affects your vehicle. Contact an authorized Jaguar service facility to determine
whether this bulletin applies to a specific vehicle.
INFORMATION
This reissue replaces all previous versions. Please destroy all previous versions.
This bulletin supersedes TSB JTB00544NAS1/2017 dated 09 JAN 2017, which should either
be destroyed or clearly marked to show it is no longer valid (e.g. with a line across the page).
Only refer to the electronic version of this Technical Bulletin in TOPIx.
Changes are highlighted in blue
SECTION:
501-03
SUBJECT/CONCERN:
Front/Rear Door Primary Seal Lower Edge Loose/Adrift
AFFECTED VEHICLE RANGE:
MODEL:
XF (X260)
MODEL YEAR:
2016-2020
VIN:
Y00001-Y85201
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
ASSEMBLY PLANT:
Castle Bromwich
1/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
A front and/or rear door primary seal may become loose/adrift from the lower edge of the
door.
CAUSE:
To be confirmed.
ACTION:
Follow the instructions below.
PARTS:
NOTE:
Door trim panel clip quantity is per door. Order the specified quantity (9 or 10) for
each Door Primary Seal being replaced.
PART NUMBER
DESCRIPTION
QUANTITY
T2H1222
Door Primary Seal
1-4
T4N9812
Door Trim Panel Clip - Front door
9
T4N9812
Door Trim Panel Clip - Rear door
10
WARRANTY:
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
2/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
NOTES:
Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Use TOPIx to obtain
the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
F-PACE and XF - Front Door Seal - Renew
76.40.01
0.7
DS
T2H1222
XE - Front Door Seal - Renew
76.40.01
0.6
DS
T2H1222
XE and XF - Rear Door Seal - Renew
76.40.02
0.6
DS
T2H1222
F-PACE and XE long wheel base - Rear Door
Seal - Renew
76.40.02
0.7
DS
T2H1222
DESCRIPTION
NOTE:
Normal Warranty procedures apply.
SERVICE INSTRUCTION:
1.
Identify the door primary seal(s) as per the Customer concern.
2.
Remove the identified door interior trim panel (see TOPIx Workshop Manual section:
501-05 - Interior Trim and Ornamentation - Front/Rear Door Trim Panel ).
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
3/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
3.
NOTE:
Front left door shown; others similar.

Remove the door frame interior finisher trim.
4.
NOTES:
The taped line must precisely follow the inner edge of the door primary
seal.
Front right door shown; others similar.

Using a suitable tape, mark the position of the inside edge of the door primary seal
following its profile around the whole door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
4/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
5.
NOTE:
Front right door shown; others similar.

On the lower edge of the door, mark the center position where the two ends of the
door primary seal join on the tape already applied.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
5/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
6.
NOTES:
Take note of the profile orientation of the door primary seal before
removal.
Remove the door seal at 30 degrees to the plane in which it is fitted
while keeping it under tension to reduce the amount of adhesive left
behind.
Front right door shown; others similar.

Remove and discard the door primary seal.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
6/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
7.
NOTES:
Take care not to move or damage the taped line around the door.
Front right door shown; others similar.

Clean and remove any remaining door seal adhesive from the edge of the door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
7/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
8.
NOTES:
Make sure the replacement door primary seal is installed in the same
profile orientation as the original.
Make sure to exactly follow the marked line when installing the new
door primary seal.
Front right door shown; others similar.

Starting with one end of the new door primary seal, start installing the seal against
the outside of the taped line at the point previously marked on the lower edge of
the door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
8/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
9.
NOTE:
Front right door shown; others similar.

Using a suitable tool, trim the excess length off the newly installed door primary seal
so that it meets the other end of the seal on the lower edge of the door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
9/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
10.
NOTE:
Front right door shown; others similar.

After installing the replacement door primary seal, apply pressure to the seal around
the full circumference using a roller or similar to make sure the adhesive bonds to
the door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
10/12
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
11.
NOTE:
Front right door shown; others similar.

Remove the tape around the door seal.
Clean and remove any remaining adhesive.
12.
NOTE:
Front left door shown; others similar.

Install the door frame interior finisher trim.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
11/12
12/16/2020
13.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
Install the door interior trim panel (see TOPIx Workshop Manual section: 501-05 Interior Trim and Ornamentation - Front/Rear Door Trim Panel ).
14.
Close the door.
15.
Only if necessary: repeat steps 2-14 to any other affected door identified in Step 1.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124057591
12/12