TSB-22-13-001

SUBJECT:
CIRCULATE TO:
CHECK ENGINE LIGHT ILLUMINATES OR ENGINE
MALFUNCTION POWER REDUCED SERVICE
NOW WARNING MESSAGE APPEARS WHILE
IDLING OR DRIVING
[ X ] SERVICE ADVISOR
No:
TSB-22-13-001
DATE:
January 2022
MODEL:
2022 Outlander
[ ] GENERAL MANAGER
[ X ] PARTS MANAGER
[ X ] TECHNICIAN
[ X ] SERVICE MANAGER
[ X ] WARRANTY PROCESSOR
[ X ] SALES MANAGER
PURPOSE
This reflash is to correct the ECU software. The check engine light illuminates or an engine
malfunction power reduced service now warning may appear while idling or driving. DTC P0401, P0404
or others may be set. Please perform this reflash first, then proceed to diagnosing other codes if they
persist.
Please reprogram the Engine Control Module (ECU) with countermeasure software to correct the issue
for any affected vehicles that come in for service (with customer approval) and any in dealer
inventory.
AFFECTED VEHICLES
2022 Outlander - built prior to December 16, 2021
REPAIR PROCEDURE
•
•
•
•
•
•
Confirm your MUT-III SE is updated with the latest reprogramming database.
Write down all the electrical device settings such as A/C and radio before reprogramming. The
settings should be restored after reprogramming.
Turn off all electrical devices to minimize the vehicle's electrical load. Also use an external
power source to ensure that the vehicle battery maintains the specified voltage during
reprogramming.
Make sure the USB cable and MUT-III SE main harness are not damaged.
Connect the MUT-III SE to an AC power source to prevent internal battery discharge.
Stay away from the under hood area during reprogramming. If the connection between the
engine ECU and ETACS is lost, the cooling fan operates as fail-safe.
NOTE: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated before
reprogramming, and DTCs are listed in the ECU memory, save the ALL-DTC results and then
erase the codes prior to reprogramming. If hard codes are present that are applicable to the
target ECU and won’t clear, diagnose and repair these codes first and then proceed with
reprogramming.
IMPORTANT
To maximize customer satisfaction with the quality of their vehicle, affected new or used
inventory vehicles should be remedied before the vehicle is delivered.
Copyright 2022, Mitsubishi Motors North America, Inc.
The information contained in this bulletin is subject to change. For the latest version of this document, go to the Mitsubishi
Dealer Link, MEDIC, or the Mitsubishi Service Information website (www.mitsubishitechinfo.com).
1/7/2022
Page 1 of 9
(5166)
EQUIPMENT
•
•
•
•
•
•
•
The following equipment is needed to reprogram the ECU:
VCI (Vehicle Communication Interface) or VCI Lite - MB991824 or MB992744
MEDIC Laptop/Tablet with A/C power adapter - 520924, or FZG1MK2
MUT III Main Harness "A" (blue connector at the DLC end) - MB991910 or MB992745
USB 2.0 Cable - MB991827 or MB992747
MEDIC 3.5/4 update at 720 or higher
For Standalone MUT III units, MUT3-SE Reprogramming Database N211201 or higher
ECU REPROGRAMMING CHART
REPAIR PROCEDURE
SOFTWARE/MEDIC VERSION VERIFICATION
1.
Verify that the ECU has not already been updated to the latest S/W number in the tale above.
If the Engine ECU is at the latest level, reprogramming is not necessary.
NOTE: Reprogramming the Engine ECU with the latest database (e.g., N211201) includes all
past and current reprogramming for TSBs of affected vehicles. It is not necessary to
reprogram the ECU for each previous TSB.
For MEDIC 3.5/4 users only: (MUT-III SEV users go to step 5)
2. Verify the MEDIC 3.5/4 is at version 3.5 and at update 720 or higher.
If your MEDIC 3.5/4 update is at least 720, continue with the Reprogramming Procedure. If your
MEDIC 3.5/4 update is below 720, update your MEDIC as follows.
1/7/2022
Page 2 of 9
(5166)
3. Select the MEDIC 3.5/4 Admin tab and click on “Updates”.
4. If the MEDIC update screen advises updates are available, click the “Begin” button.
After all updates are complete, GO TO THE REPROGRAMMING PROCEDURE.
5. STANDALONE MUT-III SE SCAN TOOL VIEWER (STV) ONLY: (MEDIC 3.5 USERS – GO TO THE
REPROGRAMMING PROCEDURE). Verify that your MUT3-SE has the most current version of the
reprogramming database from the MUT3-SE Main Page.
1/7/2022
Page 3 of 9
(5166)
a. Click “STV”.
b. Click the “ECU Reprogramming” button.
c. Click “SDB Data List, select the reprogramming data system and press the OK button”.
d. Confirm that the database number displayed in the upper right above the chart is
N211201 or higher
i. If the database number displayed on your MUT3-SE is N211201 or greater,
continue to the next section.
ii. If the reprogramming database number displayed on your MUT3-SE is lower than
N211201, then the MUT3-SE database needs to be updated.
e. Once the database number
is confirmed, hit the Home
button to go back to the
System Select screen.
1/7/2022
Page 4 of 9
(5166)
REPROGRAMMING PROCEDURE
! CAUTION
To ensure that the vehicle battery maintains 12V during the procedure, hookup a battery charger to the vehicle during the procedure.
NOTE: VCI Stand−alone reprogramming is not available for this procedure. The laptop/tablet
and the VCI must remain connected for the entire procedure.
1. Connect the equipment as follows:
NOTE: VCI Lite and MEDIC 4.0 Toughpad shown for illustration purposes only.
Data Link
Connector (Blue
End)
MUT−III SE
Main Harness
•
Turn the MEDIC PC/tablet on. If the battery
indicator in the lower right hand corner of the
screen does not show a full charge, it is
recommended that either the battery be charged
prior to beginning or be used with the A/C power
adaptor connected.
•
Connect the USB cable to the VCI/VCI Lite. When
the laptop/tablet displays the MUT-III SE main
screen, connect the USB cable to the device.
•
Connect the MUT-III SE main harness with the
blue DLC connection to the VCI/VCI Lite. Connect
the blue connection of the MUT-III SE main
harness to the vehicle's data link connector.
•
For VCI only (p/n MB991824): Turn the VCI power
switch ON. Verify that the indicator lamp in the
upper right corner of the screen is green.
USB Cable
Toughpad
(back)
VCI Lite
! CAUTION
DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS DURING THE REPROGRAMMING
PROCESS AS IT COULD CAUSE THE CONTROL UNIT TO LOSE DATA. IF THE USB CABLE IS
DISCONNECTED DURING THIS PROCEDURE, A WARNING MESSAGE WILL DISPLAY.
NOTE: Due to limited space it may be easiest to connect cable onto negative ground post and
ground strap as shown below.
2. Turn the ignition switch to the “ON”
position.
1/7/2022
Page 5 of 9
(5166)
3. Using MEDIC, from the main page, click the
“MUT3-SE” icon at the top center of the
screen.
4. The System Select screen opens and
populates with some basic information
from the vehicle. Look at the label on the
passenger side B pillar to identify the
appropriate class. (See B pillar label below;
class is labeled as “model”). If necessary,
select the correct class from the drop-down
list.
5.
Verify that the ECU has not already been updated to the latest S/W number shown in the
“ECU Reprogramming Chart” in this TSB. If the ECU is at the latest level, reprogramming is not
necessary. If reprogramming is necessary, proceed with the following steps.
a. Select ECU Reprogramming
(SDB).
b. Select “Engine” from
Systems List and click
the OK button.
1/7/2022
Page 6 of 9
(5166)
c. Click the Selection box and the
OK button.
d. After confirming the reprogramming
data listed, click the OK button to begin
reprogramming the ECU.
e. Login to the MMC Web Application.
f. Reprogramming will begin and a progress bar will appear followed by a notification upon
successful completion.
1/7/2022
Page 7 of 9
(5166)
6. Confirm the reprogramming results and press
the OK button. Return to the System Select
screen by pressing the arrow button.
a. Select the ECU Information Tab to view
the data.
b. Press the ALL DTCs button on the System
Select tab to check DTCs.
c. Press the Erase and Read all DTCs button.
d. Select all systems.
e. The results are displayed during the erase
and read process.
1/7/2022
Page 8 of 9
(5166)
f. Confirm that the erasing and checks have
been completed and that no DTCs were
detected.
7. Using a ball-point pen, enter the appropriate ECU part number, Software Part Number (ROM
ID#), this Technical Service Bulletin number, your dealer code, and the current date on the
Engine Compartment/Control Module Label (p/n MSSF024G00). The Vendor Code is not
applicable. The label is available from your facing PDC.
8. Test drive the vehicle to confirm proper operation.
WARRANTY
This bulletin is supplied as technical information only and is not an authorization to repair.
If an affected vehicle is reported with the described condition, diagnose the condition,
repair as described in this bulletin and submit a normal warranty claim using the
information below.
1/7/2022
Page 9 of 9
(5166)