ITB14-011F

Service Bulletin Details

Public Details for: ITB14-011F

Remote engine start not working this bulletin has been amended. See amendment history on the last page. Please discard previous versions of this bulletin.


- 2022 - 2021 - 2020 - 2019 - 2018 - 2017 - 2016 - 2015 -

Classification:
Reference:
Date:
EL14-003F
ITB14-011F
January 26, 2022
REMOTE ENGINE START NOT WORKING
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
2016-2022 Q50 (V37)
2016-2018 Q50 Hybrid (HV37)
2017-2022 Q60 (CV37)
2019-2022 QX50 (J55)
APPLIED SYSTEMS:
Equipped with Remote Engine Start
2022 QX55 (FJ55)
2015-2020 QX60 (L50)
2015-2017 QX60 Hybrid (L50H)
2015-2022 QX80 (Z62)
SERVICE INFORMATION
If a client states the Remote Engine Start (RES) feature is “not working”, make sure the system is properly set
to operate as follows:






The ignition is turned OFF
The Remote Engine Start function has been switched to the ON position in Vehicle Settings of the
vehicle information display
The shift selector is in Park (P)
The hood, doors, and trunk lid/lift gate are completely closed
The other Intelligent Keys are not inside of the vehicle
The Intelligent Key is within the operating range of 197 ft / 60 m
If the above conditions are met, RES should work. Perform steps 1-4 on the next page to verify if the system is
working properly.
When there is a concern with the RES feature not working properly, make sure to verify the incident before
starting any diagnosis and/or replacing parts.
For a better understanding of the RES system, refer to section 3: Pre-driving checks and adjustments >
Remote Engine Start in the vehicle owner’s manual.
When diagnosing RES operation, use the Supplemental RES Service Information and Supplemental
Diagnosis Table (starting on page 2) in addition to the ESM.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who
have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition
may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle.
1/5
Supplemental RES Service Information
Operate RES as instructed below to verify if the system is working properly.
1. Start the engine with the push-button ignition switch.
2. Turn the ignition OFF, and then wait six (6) seconds.
3. Exit the vehicle, make sure all doors are closed, and then lock the vehicle with the Intelligent Key.
4. Within five (5) seconds of pressing the LOCK button, point the Intelligent Key at the vehicle, and then press
and hold the RES button until the turn signal lights flash and the parking lights turn ON.

The engine should start, the parking lights should remain ON, and the doors should remain locked
while the engine is running.
o If the above conditions do not occur, use the Supplemental Diagnosis Table below in addition to
the ESM.
Supplemental Diagnosis Table
The engine
does not start
using the RES
feature
(see steps
1-4, above)
Possible Cause
Confirmation of Cause
Resolution
1
ECM has not
completed the shutdown
procedure after
engine/ignition OFF.
ECM has to end the
shutdown process and save
data prior to allowing RES to
operate. The shutdown
process takes six (6) seconds
to complete after the
engine/ignition is turned OFF.
Wait six (6) seconds after the
engine has stopped before
attempting RES activation.
2
RES is correctly activated
more than two (2) times
consecutively
OR
RES is activated once, and
with the engine running,
another request is generated.
Not possible to confirm how
many times RES has been
activated.
Perform steps 1-4, above.
This action will reset the
counter.
One or more Intelligent Keys
for the vehicle are still inside
the vehicle.
With all known Intelligent
Keys outside and out of
range of the vehicle, try to
turn ON the ignition with
push-button ignition switch.
If the ignition turns ON, at
least one Intelligent Key is
inside the vehicle.
Find and remove all
remaining Intelligent Keys
from the vehicle, lock doors
with the Intelligent Key, and
then perform RES.
3
2/5
ITB14-011F
Supplemental Diagnosis Table (cont’d)
Possible Cause
Confirmation of Cause
Resolution
Close and lock all doors
and trunk lid/lift gate.
Confirm both conditions in
BCM Data Monitor:
4
Doors and trunk lid/lift gate
are not closed and locked.
Doors and trunk lid/lift gate
may not be completely
closed and locked.
All doors closed Status SW = OFF
All doors locked Status = LOCK
If switches still do not show
correct status, diagnose
further with ESM.
The engine
does not start
using the RES
feature
(see steps
1-4 on page 2)
5
Door LOCK button on
the Intelligent Key was not
pressed prior to activating
RES.
Not possible to confirm the
LOCK button was pressed
first.
Press the LOCK button
before pressing and holding
the RES button.
6
RES button on the
Intelligent Key is not held
long enough.
Not possible to confirm how
long RES button was held.
Hold the RES button for
more than two (2) seconds
to activate RES.
7
Waited longer than
five (5) seconds to activate
RES after door lock
operation.
Not possible to confirm how
long RES was pressed after
lock.
Press and hold the RES
button within five (5)
seconds of pressing LOCK
button.
8
Ignition switch is not in OFF
position.
Verify if ignition switch
position (status) is in any
status other than OFF.
Change the ignition switch
to OFF status.
Verify the shift selector
is in Park position.
Confirm in
BCM Data Monitor:
9
The vehicle shift selector is
not in Park position.
Shift selector may look to
be in Park but is not.
PN Switch = ON
(with shift selector
in Park)
If PN switch = OFF,
diagnose further
with ESM.
Confirm in
BCM Data Monitor:
10
Shift selector release button
is not in released
(un-pressed) position.
-
Detent SW = OFF
(when release button
is not pressed)
If Detent SW = ON,
diagnose further
with ESM.
3/5
ITB14-011F
Supplemental Diagnosis Table (cont’d)
11
12
Possible Cause
Confirmation of Cause
Resolution
Environmental factors block,
reduce, or scramble signal
strength from Intelligent Key
to BCM.
Devices inside the vehicle
may cause RF interference,
such as after-market alarms,
highway toll passes, cell
phones or garage door
opener remotes.
Remove all devices that may
cause RF interference inside
the vehicle.
Stop lamp switch is
misadjusted or inoperative,
giving a stop lamp switch ON
signal (or brake pedal is
applied).
Stop lamp switch adjustment
may not be within
specification.
Confirm switch operation
using ABS Data Monitor:
Stop Lamp SW = OFF (with
brake pedal released, not
pressed)
Adjust / replace stop lamp
switch.
Check as needed:
The engine
does not start
using the RES
feature
(see steps
1-4 on page 2)
13
14
Hood may not be
completely closed.
Hood is open.
Security system is currently
activated (activation keeps
engine from starting).
NOTE: The horn may not be
heard and lights may not be
flashing.
Check the security system
activation by trying to start
engine normally (with pushbutton ignition switch).
NOTE: The engine will not
start with the security system
activated.
 Verify the hood is
closed.
 Confirm the hood
switch connection
is secure.
 Confirm hood switch
operation using IPDM
Data Monitor:
Hood Switch-2 = ON
(when hood is closed)
 Adjust / replace
switch.
Turn OFF/deactivate the
security system (unlock
doors with Intelligent Key). If
condition persists, diagnose
further using ESM.
15
RES is attempted from within
the vehicle.
RES can only operate
from outside the vehicle
with doors locked.
Exit the vehicle WITH the
Intelligent Key, lock the
doors, and active RES within
five (5) seconds.
16
Specific DTCs (B261B,
B26FE, B26FD) may prevent
RES from operating.
Confirm with C-III plus
that no DTCs are stored.
Clear DTC(s) with C-III plus.
If DTC(s) persist, perform
further diagnosis using the
ESM.
4/5
ITB14-011F
AMENDMENT HISTORY
PUBLISHED DATE
REFERENCE
DESCRIPTION
February 19, 2014
ITB14-011
Original bulletin published
January 5, 2015
ITB14-011a
APPLIED VEHICLES section revised
June 20, 2016
ITB14-011b
Title, and APPLIED VEHICLES and SERVICE INFORMATION
sections revised
July 27, 2016
ITB14-011c
Supplemental Diagnosis Table revised
August 13, 2019
ITB14-011d
APPLIED VEHICLES section and Supplemental Diagnosis
Table revised
October 18, 2019
ITB14-011e
APPLIED VEHICLES section and page 1 revised
January 26, 2022
ITB14-011F
APPLIED VEHICLES section revised
5/5
ITB14-011F


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.