Chrysler Sebring 1997

• Recall 84389 [USA]: If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
  Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
  federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.
  this recall only pertains to replacement control arm assemblies and has no relation to any original equipment installed on vehicles manufactured by chrysler llc.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 68291 [USA]: Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
  Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
  qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.
  this recall only pertains to aftermarket ball joints and has no relation to any original equipment installed on vehicles produced by chrysler.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 83079 [USA]: Decreased lighting visibility may result in a vehicle crash.
  Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." these lamps do not contain the required amber side reflectors.
  sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on may 11, 2009. Owners may contact sabersport at 1-909-598-7589.
  this recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by sabersport.The list can be found under "document search" located at the bottom of your screen.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 88279 [USA]: In the presence of an ignition source, a fuel leak could result in a fire.
  Certain airtex fuel pump module assemblies, p/n e7081h, sold for use as replacement equipment for the vehicles listed above. The wall of the flared fitting of the fuel pump is not thick enough to prevent the mating threaded fittings from bottoming out before an adequate seal is achieved. This condition may result in leakage of fuel at the connection of the vehicle fuel line and the fuel pump module assembly.
  airtex will notify owners and replace the fuel pumps free of charge. The recall is expected to begin during july 2007. Owners can contact airtex automotive at 800-880-3056.
  airtex recall no. FP072007-1.This recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles manufactured by daimlerchrysler or mitsubishi.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 46581 [USA]: Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
  Certain airtex fuel pump modules, p/nos. E7089m, e7094m, e7113m, and e7129m, manufactured between june 1 and september 24, 2006. These fuel pump modules were sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
  airtex will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 18, 2006. Owners may contact airtex toll-free at 1-866-867-3759.
  this recall only pertains to aftermarket fuel pump modules and has no relation to any original equipment installed on vehicles by daimlerchrysler.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 38032 [USA]: Lack of amber side reflectors in the lamps will decrease lighting visibility to other drivers and may possibly result in a vehicle crash.
  Certain tradesonic combination lamps sold as replacement lamps for use on the above listed passenger vehicles. Combination lamps not equipped with amber side reflectors fail to conform with the requirements of federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment.
  tradesonic will notify owners and replace the lamps free of charge. The recall is expected to begin during july 2006. Owners may contact tradesonic at 626-934-8884.
  this recall only pertains to tradesonic aftermarket lamps and has no relation to any original equipment installed on the listed passenger vehicles.For more information on the lamp model numbers, click on document search and view document titled "lamp model numbers."customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 41985 [USA]: Either circumstance may result in the vehicle rolling away without warning.
  On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
  dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1-800-853-1403.
  daimlerchrysler recall no. C45.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 1033 [USA]: This could potentially result in a loss of throttle control, increasing the risk of a crash.
  On certain passenger vehicles equipped with 2.5l v6 engines, the throttle control cable can fray causing the throttle to bind or stick.
  dealers will replace the throttle cable assembly. Owner notification began august 5, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-853-1403.
  daimlerchrysler recall no.B22.Also, customers can contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 3413 [USA]: This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash. this campaign supercedes mmc's previous safety recall campaign, see 99v-066.
  Vehicle description: passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water can intrude. Also, mmc has added the potential of leaking moisture, which can cause the ball stud to corrode.
  dealers will inspect the lower lateral arm ball joint for wear. Ball joints that exhibit wear beyond the established tolerance will be replaced with newly designed lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent intrusion of moisture.
  owner notification began may 21, 2001.Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 8019 [USA]: If the cover separates while driving, it could distract the driver increasing the risk of a crash.
  This is not a safety recall in accordance with the safety act. However, it is deemed a safety improvement campaign by the agency. Vehicle description: passenger vehicles. If the convertible top cover is not installed correctly, it can separate unexpectedly from the vehicle while driving.
  owners will receive an improved convertible top cover instruction label and installation instructions.
  daimlerchrysler has decided to conduct a customer satisfaction notification to send instruction labels to owners.Owners can contact daimlerchrysler at 1-800-992-1997.

  Show Content

• Recall 14233 [USA]: If this happens, the "ignition-park" interlock system will be nonfunctional.
  Vehicle description: passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
  dealers will inspect for proper operation of the system. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a "self-adjusting" design.
  owner notification began october 26, 1998. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-992-1997.Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 15681 [USA]: Separation of the ball joint could cause a loss of steering control increasing the risk of a vehicle crash.
  Vehicle description: passenger vehicles. The lower control arm ball joint can separate due to loss of lubrication.
  dealers will inspect the ball joint end housing cover seal for leakage with a high pressure air tester and the rubber boot will be visually inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
  owner notification began december 15, 1997.Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-992-1997.Also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 13939 [USA]: The headrest support bracket can break, increasing the risk of personal injury.
  The headrest guide bracket was improperly welded to the seat back frame on the passenger side seat back assemblies only.
  dealers will replace the passenger seat back assembly with a new assembly.
  owner notification:owner notification began july 31, 1997. Note:owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 2001062 [Canada]: Steering
  On certain vehicles, the lower lateral arm ball joint can separate due to loss of lubrication. There is a potential for moisture to leak past the protective boot which can cause the ball stud to corrode. This corrosion, acting much like contamination, can also lead to premature wear and separation of the ball joint. This could result in loss of vehicle control and a possible crash. Correction: lower lateral arm ball joints will be inspected for wear and replaced as necessary with newly designed lower lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent the intrusion of moisture.

  Show Content

• Recall 1998165 [Canada]: Other
  Note: vehicles equipped with a floor mounted automatic transmission shift lever. A combination of applying a mis-adjusted shifter release button with a low force attempt to shift out of park with the key in the locked position may break the connecting pin in the shifter. If this happens, the "ignition-park" interlock system will not function. Correction: the console shift interlock mechanism will be inspected for proper function. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a current production "self adjusting" design.

  Show Content

• Recall 1997122 [Canada]: Seats and restraints
  There is the potential for the passenger side headrest support bracket weld to fail on these vehicles. Correction: a new passenger seat back assembly will be installed on affected vehicles.

  Show Content

• Recall 1997205 [Canada]: Suspension
  On certain vehicles, the lower control arm ball joint may separate due to loss of lubrication. This separation could result in loss of vehicle control and a crash without prior warning. Correction: ball joint end housing cover seal will be inspected for leakage and the rubber boot will be inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.

  Show Content

• Recall 2004003 [Canada]: Other
  On certain vehicles equipped with an automatic transmission and a floor-mounted shifter, the ignition-park interlock may become defeated and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position. This may result in the vehicle rolling away without warning. Correction: dealer will inspect the function of the ignition-park interlock system. Vehicles found with functional interlock systems will have a load-limiting push rod installed into the floor shifter lever. Vehicles with a non-functional ignition-park interlock system will have the shifter assembly replaced.

  Show Content

• Recall 2002128 [Canada]: Engine
  On certain passenger vehicles equipped with 2.5l v6 engines, the throttle control cable can fray causing the throttle to bind or stick. This could potentially result in a loss of throttle control, increasing the risk of a crash. Correction: dealers will replace the throttle cable assembly.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

The following is a list of any known keyfobs for the Chrysler Sebring 1997 as well as their FCC IDs if available

• OR-MOP016: 1997-2001 Chrysler Sebring Convertible / 4-Button Keyless Entry Remote / PN: 4671226 / KYPTX002 (OEM Refurb)
  FCC ID: KYPTX002

• Auto trans ignition-park interlock investigation # EA03011

  The manufacturer reports above are based on daimlerchrysler¿s (dc) analysis of model year (my) 1998 (population = 356,384) and 1999 (population = 486,948) ja, jx and lh family subject vehicle data (earlier mys excluded).The population number includes all mys.The precise number of duplicates between odi and dc reports cannot be determined due to missing or incomplete information.The fatality incident involved an elderly person who attempted to stop a roll away vehicle and received fatal injuries.Odi also gathered information on my 1997-99 prowler vehicles in this investigation. The prowler vehicles were manufactured with a different design shifter mechanism (the shift lever is shorter).There are no complaints of prowler interlock failure in odi¿s database, and dc has received no reports either.The prowler is excluded from the recall scope.The investigation involved a condition where the interlock system could fail (or be made inoperative by the operator) during vehicle use, possibly inadvertently.The interlock system is required under fmvss 114.With the transmission in the park position and the ignition key off, the combined action of pressing the shift button and pulling the shift lever rearward may result in the operator overcoming the interlock system and cause the mechanical linkage of the system to disconnect.When this occurs, there is no overt indication to an operator that the system is defeated, and an increased risk of vehicle roll-away exists.Under recall 04v021, dc will replace damaged shift mechanisms, and will install on all vehicles a device which inhibits the operator¿s ability to overcome the interlock and defeat the system.Beginning with my 2000, dc incorporated a brake and transmission shifter interlock (btsi) system into the subject vehicles.Introduction of btsi involved design changes to the shift mechanism, one of which resulted in reduced mechanical advantage (rma) of the shift button.The rma shifter requires increased forces to overcome the interlock system, making the shifter less susceptible to damage.
  

  Show Content

• Safety belt cinching latch plate investigation # PE02082

  There are no injuries or fatalities associated with this alleged defect.While conducting this investigation, odi found that the subject cinches meet the load bearing requirements of federal motor vehicle safety standard 208, and that many of the reported failures were due to incorrect child safety seat installations. Additionally, the report rate is low (1.60/100k).The information available fails to establish the existence of a defect trend at this time.Further allocation of agency resources to this issue is unwarranted and the preliminary evaluation is being closed.
  

  Show Content

• Steering shaft binding investigation # EA99028

  There is no summary currently available
  

  Show Content

• Automatic transaxle ignition interlock investigation # EA98014

  Alleged failure of the automatic transaxle ignition interlock system that either allows the ignition key to be removed when the transmission gear selector is not in the "park" position and the transmission gear selector to be shifted when the ignition key is removed or prevents theignition key from being removed when the transmission gear selector is in the "park," or any other, position.
  

  Show Content

• Convertible top cover disengagement investigation # EA97025

  Alleged that the convertible top cover may disengage from the subject vehicles while driving.
  

  Show Content

Fire in right front dash area( passenger side) to the right of the air bag. Broke/melted front window/wiper blade, burned a 12" square hole in the dash. While driving the vehicle the driver smelt something burning--no signs of smoke, the vehicle was driven and parked over night. The damage was noticed the next morning.

Tl* the contact owns a 1997 chrysler sebring. While attempting to put on the seat belt, the seat belt did not release and fractured. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 190,000. ....Updated 07/05/16 *bf the consumer stated the solenoid was defective. Updated 07/14/16.*jb

Tl* the contact owns a 1997 chrysler sebring. The contact received notification of nhtsa campaign number: 10e059000 (suspension). While driving 3 mph, there was a loud abnormal noise emitting from the front of the vehicle. The wheel assembly fractured and the front driver side tire was bent inwards towards the engine. The vehicle was taken to the dealer. The technician diagnosed that the upper control arm was fractured and needed to be replaced. The vin was unavailable. The failure mileage was 208,000.

I purchased the 1997 chrysler sebring in november of 2014. I did notice that the passenger air bag is slightly ejected. I have gone to automotive shops and even a chrysler dealership, and both inform me that the airbags for this particular car are no longer made. I need help on how to fix this problem to ensure the safety of my passengers. Thank you for your time and have a wonderful day. *tr

Tl* the contact owns a 1997 chrysler sebring. The contact stated that the front driver and passenger side seat belts were locked and could not be released. The vehicle was not inspected by a dealer or an independent mechanic. The manufacturer was not contacted. The failure and current mileages was approximately 152,000. The vin was unavailable. *tr

Tl* the contact owns a 1997 chrysler sebring. The contact stated that while driving 30 mph, another vehicle crashed into the rear of the contact's vehicle causing it to spin several times. The vehicle was destroyed. The air bags did not deploy upon impact. The vin was unavailable. The failure and current mileage was 200,000.

Tl* the contact owns a 1997 chrysler sebring convertible. The contact stated that the driver side ball joint detached from the socket while the contact was driving. The dealer diagnosed that the lower ball joint need to be replaced. The vehicle was included in the recall associated with nhtsa campaign id number: 09e056000 (suspension:front:control arm:lower ball joint), but the manufacturer refused to cover the repairs. The manufacturer proposed that the contact pay 50 percent of the cost of the repairs due to the age of the vehicle. The vehicle was not repaired. The failure and current mileage was 115,000.

Tl* the contact owns a 1997 chrysler sebring convertible. The contact stated that the driver side seat belt remained stuck in the retracted position and he was unable to use the seatbelt. The dealer informed the contact that there were no recalls and offered no further assistance. The manufacturer had not been notified of the failure nor was the vehicle diagnosed or repaired. The current mileage was 111,320 and the approximate failure mileage was 111,300.

I have a 1997 chrysler sebring jxi convertible, that the seatbelt are generally useless. Both the passenger and driver seat belts lock and will not retrack, therefore you are not able to use them. This is a safety hazard especially in a convertible. I live in a state where seatbelts are requires, but when they are locked i can not use them. I have not found where the seatbelts have been recalled, shouldn't there be a lifetime guarantee on seatbelts since they are a safety device? I have owned the car for 3 years now and it is an ongoing situation with the most recent being yesterday. *tr

Common OBD-II Error Codes

• P0720 [1] Output Speed Sensor Circuit Malfunction
• P361A [1] P361A
• P0442 [1] Evaporative Emission Control System Leak Detected (small leak)
• P0455 [1] Evaporative Emission Control System Leak Detected (gross leak)
• P0456 [1] Evaporative Emissions System Small Leak Detected
• P1494 [1] EGRCHK Solenoid Circuit Malfunction