Dodge Nitro 2wd 2010

• Recall 149940 [USA]: Projectiles as a result of driver air bag deployment in the event of a crash can increase the risk of injury.
  Chrysler (fca us llc) is recalling certain 2008-2010 chrysler town and country and dodge grand caravan and 2007-2011 dodge nitro vehicles. These vehicles may have a loose or missing brand emblem in the center of the steering wheel. The loose emblem or the securing nuts for the emblem within the driver air bag module may become projectiles in the event of a driver air bag deployment.
  chrysler will notify owners, and dealers will replace the driver's air bag cover with a redesigned cover, free of charge. The recall began february 11, 2021. Owners may contact fca us llc customer service at 1-800-853-1403. Chrysler's number for this recall is w09.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 68840 [USA]: This could lead to loss of brake fluid and reduced braking performance increasing the risk of a crash.
  Chrysler is recalling certain model year 2010 left hand drive jeep liberty, dodge nitro and ram 1500 truck; right and left hand drive jeep wrangler vehicles. These vehicles may have been built with an improperly formed master cylinder to hydraulic control unit (hcu) brake tube assembly end flare.
  dealers will replace the brake tubes free of charge. The safety recall is expected to begin during august 2010. Owners may contact chrysler toll-free at 1-800-853-1403.
  chrysler safety recall no. K15.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 74150 [USA]: This could result in brake failure without warning which could cause a crash.
  Chrysler is recalling certain model year 2010 chrysler sebring; dodge avenger and nitro; jeep liberty, commander and grand cherokee; and model year 2009-2010 dodge ram truck. These vehicles may have been built with an improperly formed or missing brake booster input rod retaining clip.
  chrysler will replace the brake booster input rod retaining clip free of charge. The safety recall is expected to begin during february 2010. Owners may contact chrysler at 1-800-853-1403.
  chrysler's safety campaign number is j37.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall R/2020/251 [UK]: The driver's airbag emblem may have become loose or detached
  The driver?S airbag emblem may have become loose or detached.
  remove the emblem and the emblem retainers

  Show Content

• Recall 2020311 [Canada]: Airbag
  Issue: on certain vehicles, the emblem on the steering wheel could become loose. If this happens, the emblem or its retainers could become projectiles when the airbag inflates in a crash. Safety risk: loose parts that are projected toward the occupants when an airbag deploys could increase the risk of an injury. Corrective actions: fca canada will notify owners by mail and instruct you to take your vehicle to a dealer to replace the airbag cover on the steering wheel.

  Show Content

• Recall 2010009 [Canada]: Brakes
  On certain vehicles, the brake booster input rod may have been installed without the retaining clip, or in some cases, with an improperly formed retaining clip. Should the input rod separate from the assembly it could lead to a loss of brakes, which could result in a vehicle crash causing property damage, personal injury or death. Correction: dealers will install or replace the retaining clips.

  Show Content

• Recall 2010223 [Canada]: Brakes
  Certain vehicles may have an improperly formed master cylinder to hydraulic control unit brake tube assembly end-flare that could lead to a loss of brake fluid and reduced braking performance. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: dealers will replace the suspect brake tubes.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Air bag acu electrical overstress investigation # EA19001

  The office of defects investigation (odi) is expanding the investigation to include the equipment supplier and vehicle manufacturers (oems) using this unit.The investigation focuses on acus manufactured by trw, now zf-trw (zf) , the tier-one supplier to hyundai and kia and the other affected oems.The acu senses a vehicle crash to determine whether air bag deployment is required, and if so, deploys the appropriate air bags and other supplemental restraints.Zf supplied subject acus to six oems: fca, honda, hyundai, kia, mitsubishi and toyota.Internal to the acu is an electronic component (an application specific integrated circuit, or asic) that monitors signals from crash sensors.A failure of the asic may prevent deployment of the required air bags and devices, or may otherwise affect the proper operation of the acu.The acu is located in the passenger compartment, and electrical wiring connects the asic to sensors located at the front of the vehicle.Odi’s current understanding is that a crash event may, in and of itself, produce harmful signals on the sensor wiring capable of damaging the asic, although the probability of this occurring appears to be low.While the acu incorporates electrical circuitry intended to protect the asic from harmful signals, the level and effectiveness of the protective circuitry varies by oem customer.During pe18-003, hyundai and kia filed recalls (18v-137 and 18v-363 respectively) to address a defect that could result in acu disablement and non-deployments.According to the filings, the disablement occurs in certain types of frontal crash events.Both filings discussed a condition known as electrical overstress (eos) that affected the subject asic and was likely caused by electrical signals that entered the acu via sensor wiring.The recalled vehicles used acus that had the lowest levels of asic protection while non-recalled hyundai and kia products using subject acus had higher levels of protection.Odi has not identified any eos failures in the non-recalled kia and hyundai populations.In september 2016, fca filed recall 16v-668 for certain model year (my) 2010 to 2014 chrysler, dodge and jeep products also manufactured with the subject acu.In that filing, fca also discussed an eos condition that resulted in a failure of the subject asic, which caused air bag non-deployment. Fca noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle.Other fca vehicles that also used the subject acu, but not the cross-car harnessing, had not experienced eos failures, despite similar time in service. The recalled fca vehicles used a mid-level form of asic protection.Other fca vehicles that did not use cross car wiring, or used higher levels of asic protection, have not been recalled.Odi has not identified any eos failures in the non-recalled fca population.Recently, odi has identified two substantial frontal crash events (one fatal) involving toyota products where eos is suspected as the likely cause of the non-deployments.The crashes involved a my 2018 and a my 2019 corolla equipped with the subject acu that incorporated higher levels of asic protection.Additionally, both acus were found to be non-communicative (meaning the acu could not be read with an event data recorder) after the crash, a condition found in other cases where eos occurred with other oems.No other eos events have been identified for other toyota products (including corolla models that used the subject acu since my 2011), or for the honda and mitsubishi vehicles that use the subject acu.Odi plans to evaluate the susceptibility of the subject acu designs to electrical signals, as well as other vehicle factors that can either lead to, or reduce the likelihood of, an eos event.Additionally, odi will evaluate whether an unreasonable risk exists that requires further field action.
  

  Show Content

• Totally integrated power module failure investigation # DP14004

  In a letter dated august 21, 2014, the center for auto safety (cas) petitioned the national highway traffic safety administration (nhtsa) to initiate a defect investigation of alleged failures associated with the totally integrated power module (tipm) installed in chrysler suv’s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that tipm defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On september 25, 2014, the office of defects investigation (odi) opened dp14-004 to evaluate the petition for a grant or deny decision. Odi analyzed complaint data provided by cas as well as complaints submitted to odi from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with tipm-7. Approximately 3 percent of cas complaints are related to vehicles equipped with tipm-6 and odi’s review of these complaints did not identify any safety defect trends. Odi conducted a detailed review of complaints narratives submitted by cas and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available customer assistance inquiry reports (cair). Analysis of the field data indicated that my2011-2013 jeep grand cherokee and dodge durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (fpr) failures than other subject vehicles. In a september 3, 2014 letter to nhtsa, chrysler submitted a defect information report (dir) identifying a defect in the fpr within the tipm-7 which can result in a no start or stall condition in approximately 188,723 model year (my) 2011 jeep grand cherokee (wk) and dodge durango (wd) vehicles manufactured from january 5, 2010 through july 20, 2011 (14v-530).In a february 24, 2015 letter, chrysler submitted a second dir expanding the scope of the fpr defect condition to include an additional 338,216 my 2012 through 2013 jeep grand cherokee vehicles manufactured from september 17, 2010 through august 19, 2013 and my 2012 through 2013 dodge durango vehicles manufactured from january 18, 2011 through august 19, 2013 (15v-115).Odi analysis of the cas allegations of tipm defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the tipm assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from tipm faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioners contentions relate to the defect condition addressed by the chrysler recalls, the factual bases of the petitioners contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a nhtsa order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize nhtsas limited resources to best accomplish the agencys safety mission, the petition is denied. This action does not constitute a finding by nhtsa that a safety-related defect does not exist. The agency will take further action if warranted by future circumstances. Please see the federal register notice in dp14-004 file (www-odi.Nhtsa.Dot.Gov/defects).
  

  Show Content

I got my dodge nitro 4 months ago first month i noticed my engine was starling and i know is i had electric issues i told my dealership and they said that if the car still running it's nothing they can do about it some days my windshield wiper will cut on by itself some days my blinker don't work i have 6 month warranty . So i was on my way going home coming off the freeway stop at the red light the light hit green i press the gas my wheels lock up my brake lock up and the car keep going into oncoming traffic my car is going into the wrong lane i have pictures of that making. Hard for me to turn my wheel now my car been in the shop for a month still paying payments

I got my dodge nitro 4 months ago first month i noticed my engine was starling and i know is i had electric issues i told my dealership and they said that if the car still running it's nothing they can do about it some days my windshield wiper will cut on by itself some days my blinker don't work i have 6 month warranty . So i was on my way going home coming off the freeway stop at the red light the light hit green i press the gas my wheels lock up my brake lock up and the car keep going into oncoming traffic my car is going into the wrong lane i have pictures of that making. Hard for me to turn my wheel now my car been in the shop for a month still paying payments

While driving down the road, my headrest malfunctioned and unexpectedly deployed. The vehicle was not hit, nor has it ever been. The vehicle was in motion on a city street, slowing down to approach a stoplight.

While driving down the road, my headrest malfunctioned and unexpectedly deployed. The vehicle was not hit, nor has it ever been. The vehicle was in motion on a city street, slowing down to approach a stoplight.

The ignition switch or w.I.N. Has stopped working , through research this is a common failure on these model year trucks. Unsafe as ignition may turn off while driving. Thankfully mine has not failed in that aspect, but, has failed entirely, i shut engine off, went to restart, and ignition switch failed to start vehicle.

The ignition switch or w.I.N. Has stopped working , through research this is a common failure on these model year trucks. Unsafe as ignition may turn off while driving. Thankfully mine has not failed in that aspect, but, has failed entirely, i shut engine off, went to restart, and ignition switch failed to start vehicle.

Tl* the contact owns a 2010 dodge nitro. The contact received notification of nhtsa campaign number: 20v396000 (air bags, steering) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that after having a routine check at napleton's mid rivers chrysler dodge jeep ram (44951 veterans memorial pkwy, saint peters, mo 63376, (636) 242-1471) when the vehicle was returned, the dab (digital audio broadcasting) was no longer present on the steering wheel. The manufacturer was notified of the failure however, the contact was informed that parts were not yet available. The failure mileage was approximately 35,500. Parts distribution disconnect.*dt*jb

Tl* the contact owns a 2010 dodge nitro. The contact received notification of nhtsa campaign number: 20v396000 (air bags, steering) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that after having a routine check at napleton's mid rivers chrysler dodge jeep ram (44951 veterans memorial pkwy, saint peters, mo 63376, (636) 242-1471) when the vehicle was returned, the dab (digital audio broadcasting) was no longer present on the steering wheel. The manufacturer was notified of the failure however, the contact was informed that parts were not yet available. The failure mileage was approximately 35,500. Parts distribution disconnect.*dt*jb

I was driving at about 20-30 mph. My car started making a whining sound then my dashboard lit up with multiple lights starting with the battery and then all of them. Luckily i was able to get to the side of the road before it completely died. I had it towed to a garage. They tried changing the alternator and battery. It still won't turn on. It is now at a dealership and currently can't figure out what is wrong with it.