Dodge Ram-1500-ffv 2010

• Recall 69794 [USA]: Loss of steering control of the vehicle could increase the risk of a crash.
  Chrysler is recalling certain model year 2008-2011 dodge ram 4500 and 5500 vehicles. These vehicles may experience a weakening and fracture of the left ball stud on the tie rod resulting in the potential loss of steering.
  chrysler will notify owners and replace the left outer tie rod free of charge. The safety recall began on march 7, 2011. Owners may contact chrysler at 1-800-853-1403.
  chrysler safety recall no. K28.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 86251 [USA]: Brake lights that are slow to extinguish could increase the risk of a crash.
  Chrysler is recalling certain model year 2010-2011 dodge ram trucks manufactured from march 2009 through october 2010. Some vehicles equipped with diesel engine and a hydroboost brake system may be equipped with a power steering reservoir cap with excessive vent pressure levels that may result in brake pedals that are slow to return.
  chrysler will notify owners and dealers will replace the power steering reservoir cap free of charge. The safety recall is expected to begin during february 2011. Owners may contact chrysler at 1-800-853-1403.
  chrysler safety recall no. K33. Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 68841 [USA]: This could lead to loss of brake fluid and reduced braking performance increasing the risk of a crash.
  Chrysler is recalling certain model year 2010 left hand drive jeep liberty, dodge nitro and ram 1500 truck; right and left hand drive jeep wrangler vehicles. These vehicles may have been built with an improperly formed master cylinder to hydraulic control unit (hcu) brake tube assembly end flare.
  dealers will replace the brake tubes free of charge. The safety recall is expected to begin during august 2010. Owners may contact chrysler toll-free at 1-800-853-1403.
  chrysler safety recall no. K15.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 86725 [USA]: The result of the defect could lead to a condition where the key may be removed from the ignition switch (win module) prior to placing the shifter in park. this could result in the potential for unintended vehicle movement and could increase the risk of a crash.
  Chrysler is recalling certain model year 2010 chrysler 300, dodge challenger, charger, jeep commander, grand cherokee and dodge ram vehicles. These vehicles may have been built with a wireless ignition node (win) module exhibiting a binding condition of the solenoid latch.
  dealers will inspect and replace the win module free of charge. The safety recall is expected to begin on or before august 23, 2010. Owners may contact chrysler at 1-800-853-1403.
  chrysler's recall campaign number is k08.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 74151 [USA]: This could result in brake failure without warning which could cause a crash.
  Chrysler is recalling certain model year 2010 chrysler sebring; dodge avenger and nitro; jeep liberty, commander and grand cherokee; and model year 2009-2010 dodge ram truck. These vehicles may have been built with an improperly formed or missing brake booster input rod retaining clip.
  chrysler will replace the brake booster input rod retaining clip free of charge. The safety recall is expected to begin during february 2010. Owners may contact chrysler at 1-800-853-1403.
  chrysler's safety campaign number is j37.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 2019420 [Canada]: Other
  Issue: this recall is for aftermarket replacement rear window glass produced by vitro automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: this is a voluntary recall that is not being conducted under the requirements of the motor vehicle safety act. Safety risk: glass that breaks in to large pieces could create a risk of injury. Corrective actions: the company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “dot 287” along with the lettering “vmr” (replacement market) and a date code that is before july 2019. This information is printed on the bottom corner of the glass. Consumers should contact vitro's customer service at 1-412-995-6457 or [email protected] to arrange for replacement of the glass.

  Show Content

• Recall 2018122 [Canada]: Fuel supply
  On certain vehicles, the front fuel tank strap may become loose or detached due to corrosion of the frame bracket. This could result in the front of the fuel tank to lower, potentially allowing the front of the tank to make contact with the ground, which could increase the risk of a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: dealers will install a reinforcement bracket onto the frame.

  Show Content

• Recall 2016265 [Canada]: Airbag
  On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: dealers will replace the airbag inflator. Note: canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected.

  Show Content

• Recall 2015228 [Canada]: Airbag
  On certain vehicles, the driver frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: this recall supersedes special service campaign 2015-003. Correction: dealers will replace airbag inflators. All vehicles having received a replacement inflator as part of the previous special service campaign will have a replacement inflator installed.

  Show Content

• Recall 2014449 [Canada]: Fuel supply
  On certain vehicles equipped with 6.7l diesel engines, an electrical connection at the fuel heater could overheat, potentially rendering the heater inoperative and causing a fuel leak and fuel odour. Fuel leakage, in the presence of an ignition source, could result in a fire causing injury and/or damage to property. Correction: dealers will inspect the fuel heater, and replace it if required, as well as replace the fuel heater wiring harness electrical connector.

  Show Content

• Recall 2013397 [Canada]: Steering
  On certain 2008-2012 ram 2500 and 3500 4x4, ram 3500 cab chassis, and 2008 ram 1500 mega cab 4x4 vehicles, the left outer tie rod ball stud could fracture, potentially resulting in a loss of vehicle control and a crash causing injury and/or property damage. Correction: dealers will install a redesigned left outer tie rod assembly. Note: this recall supersedes recall 2011-253 (l16). Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.

  Show Content

• Recall 2013396 [Canada]: Steering
  Certain ram 4500 and 5500 four wheel drive vehicles may experience a fracture of the ball stud on the left outer tie rod assembly, potentially resulting in a loss of vehicle control and a crash causing injury and/or property damage. Correction: as an interim repair, dealers will align the left tie rod end. Dealers will install a redesigned left outer tie rod assembly once parts are available. Note: this recall supersedes recall 2010-465 (k28). Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.

  Show Content

• Recall 2013044 [Canada]: Powertrain
  On certain vehicles, the rear axle pinion nut could loosen and allow the rear driveshaft to detach from the axle, or fully detach from the vehicle. Pinion nut separation could also cause the rear axle differential to fail suddenly, causing rear wheel lockup. These issues could result in loss of propulsion, danger to other road users, loss of vehicle control and possible crash causing property damage and/or personal injury. Correction: dealers will install a pinion nut retainer.

  Show Content

• Recall 2012327 [Canada]: Powertrain
  On certain vehicles built between july 1, 2009 and november 30, 2009, the rear axle pinion nut may have been incorrectly manufactured and could loosen. If the pinion nut was to separate from the pinion, the rear driveshaft could become detached from the rear axle, or fully detached from the vehicle. Pinion nut separation could also cause the rear axle differential to fail suddenly, causing rear wheel lockup. These issues could result in loss of propulsion, danger to other road users, loss of vehicle control and possible crash causing property damage and/or personal injury. Correction: dealers will install a pinion nut retainer.

  Show Content

• Recall 2011253 [Canada]: Steering
  On certain 2008-2011 ram 2500 and 3500 4x4, ram 3500 cab chassis 4x2 and 4x4, and 2008 ram 1500 mega cab 4x4 vehicles, the left outer tie rod ball stud could fracture. Additionally, other 2003-2008 ram vehicles may have received the affected tie rod as a replacement part during service, and are therefore also involved in this campaign. Although this condition tends to occur when making a tight turn during low speed parking lot type maneuvers, tie rod failure could result in a loss of directional stability. A loss of steering control could result in a crash causing property damage and/or personal injury. Correction: dealers will inspect and, if necessary, replace the left outer tie rod end and tighten the track bar bolt. Note: the tie rod replacement portion of this recall was superseded by recall 2013-396.

  Show Content

• Recall 2010009 [Canada]: Brakes
  On certain vehicles, the brake booster input rod may have been installed without the retaining clip, or in some cases, with an improperly formed retaining clip. Should the input rod separate from the assembly it could lead to a loss of brakes, which could result in a vehicle crash causing property damage, personal injury or death. Correction: dealers will install or replace the retaining clips.

  Show Content

• Recall 2010151 [Canada]: Other
  Certain vehicles equipped with automatic transmission may have been built with a wireless ignition node (win) module exhibiting a binding condition of the solenoid latch. This may result in a condition where the ignition key can be removed from the win module prior to placing the shifter in park. This could result in unintended vehicle movement, which may cause property damage, personal injury or death. Correction: dealers will inspect and, if necessary, replace the win module.

  Show Content

• Recall 2010223 [Canada]: Brakes
  Certain vehicles may have an improperly formed master cylinder to hydraulic control unit brake tube assembly end-flare that could lead to a loss of brake fluid and reduced braking performance. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: dealers will replace the suspect brake tubes.

  Show Content

• Recall 2010438 [Canada]: Brakes
  On certain vehicles equipped with a diesel engine and hydroboost brake system (which utilizes the power steering system pressure for brake assist), the power steering reservoir cap may have excessive vent pressure levels, which could result in a brake pedal that is slow to return once depressed. This could increase brake light illumination times and cause confusion to a following road user which, in conjunction with traffic, road conditions and driver's reactions, may result in a crash. Correction: dealers will replace the power steering reservoir cap.

  Show Content

• Recall 2010465 [Canada]: Steering
  Certain ram 4500 and 5500 vehicles may experience a weakening and fracture of the ball stud on the left outer tie rod assembly. A loss of steering control could result in a crash causing property damage and/or personal injury. Correction: dealers will replace the left outer tie rod assembly.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Outer tie rod failure investigation # PE11009

  Odi received complaints regarding failing tie rod ball studs on model year 2008-2011 dodge ram 2500 and 3500 vehicles resulting in loss of steering control.Chrysler concluded that misalignment of the left (driver side) ball stud on vehicles built with the cross car steering linkage system could allow contact between the bull stud and the ball housing which could weaken the stud and result in fracture.Chrysler submitted a recall notice on august 15, 2011 involving certain my 2003-2011 ram 2500 and ram 3500 pickup trucks built or repaired with the cross car steering linkage.Chrysler will inspect, repair or realign the front end of the subject vehicles as needed.Chryslers announcement of a safety recall on this matter addresses odis concerns.The odi reports cited above can be reviewed at www-odi.Nhtsa.Dot.Gov/owners/searchnhtsaid under the following identification (odi) numbers:10332525, 10357937, 10366591, 10303744, 10377166, 10373240, 10343969, 10375403, 10324831, 10373546, 10370771.
  

  Show Content

The contact owns a 2010 ram 1500. The contact stated while driving 35 mph, the driveshaft detached from the sub-frame of the vehicle. The contact pulled over and the vehicle was towed to an independent mechanic to be diagnosed. The contact was informed that the driveshaft needed to be replaced. There was no warning light illuminated. Upon investigation, the contact associated the failure with nhtsa campaign number: 12v474000 (power train) however, the vin was not included. The manufacturer was informed of the failure but provided no further assistance. The failure mileage was approximately 97,000.

Vehicle has 113,000 miles on it now, the engine is knocking so i brought it in to weber in detroit lakes minnesota they say it needs cams and lifters e c t. Estimate is $5,000 or new engine $9,000 so now i can't get to work! I commute back and forth every day 70 miles each way, this vehicle should not have this problem as of yet in my eyes! Will the factory / dealership warranty this fix for me? I purchased vehicle from weber in detroit lakes almost four years ago with 80,000 miles on it i have only driven at 33,000 miles since then!! I don't have that kind of money for this fix nor can i afford to buy a replacement vehicle but now the knocking you can hear it outside the vehicle but you cannot hear it in the cab of the vehicle so how long has this problem actually been going on before the fact of me noticing it just very recently so then i quit driving it immediately and brought it directly to weber as per appointment

The contact owns a 2010 dodge ram. The contact stated that while driving at various speeds the key fob released from the ignition without warning. The vehicle was taken to the local dealer who diagnosed the key fob released from the ignition while driving and reversing as the ignition module needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 109,000. The contact stated that the failure was similar to nhtsa campaign number: 10v200000 (electrical system).

The contact owns a 2010 dodge ram 1500. The contact stated while exiting out of the vehicle they mistakenly noticed that they were able to take the key out of the ignition while the engine was still running. The contact stated the failure occurred several times but the last time the vehicle battery warning light illuminated. The contact was not able to start the vehicle. The contact had the vehicle towed to an independent mechanic who diagnosed the failure as the bottom of the fuse box connection wiring had melted. The vehicle was not repaired. The manufacture was made aware of the failure. The failure mileage was 200,000.

Driveshaft disconnected/slipped out of rear diff (hanging down - still on truck) loss of power/had to coast to a safe area during coasting came to a sudden stop/something locked up in rear diff. *tr

The truck started making a whirring down shifting noise then a loud noise then the truck seized to a halt drive shaft now laying on ground. *tr

While traveling a local road at approximately 30 mph, the rear differential made a short term humming noise and then a grinding sound. Rear differential locked up shearing the pinion shaft and allowing the driveshaft to drop free of the rear differential, hit the bottom of the truck several times and then drop to the ground. Vehicle was towed to the local dealership where it remains waiting on parts. According to the dealership, chrysler has switched suppliers of the ring and pinion kits and there is currently a backorder of approximately 175 parts kits. Current release date for the parts is october 2012. *tr

While driving home 10/20 ~8pm, i was slowing down in freeway traffic ~45mph. I took my foot off the brake and was just about to press down on the accelerator pedal, my truck surged forward for about .25 of a second (split second). This has happened in the past ~8 times. I notified the dealer at 26,000 mile service and they said it was the engines switching between the eco mode and normal mode. (5.7 hemi). Please advise. (i purchased this vehicle new from folsom dodge, ca.) *tr

This is not a complaint based on a specific occurrence. I am a professional driver who operates a variety of passenger vans and busses between various cities. In recent years it has become increasingly more difficult to drive during non-daylight hours do to the type of headlights that are now allowed on passenger and truck vehicles. The intensity and brightness level of headlights has increased to a point where the glare and blinding effect of oncoming headlights has become a significant safety factor, especially on two lane highways. Furthermore, many vehicles are now equipped with a four headlight system as their regular night time running lights. The optional "fog lights" for severe weather conditions is now standard lighting protocol. The other option on these vehicles is their "bright" option which creates an even more hazardous situation for oncoming traffic due to their blinding effect. This "upgraded" headlight, fog light, and bright light trend needs to be toned back down to intensity and brightness levels that existed a few years ago and are reasonable for oncoming traffic to adjust to. It is a simple matter of fact that these high level headlight options are the cause of more unnecessary accidents and casualties than ever before. *tr

Common OBD-II Error Codes

• P0201 [1] Injector Circuit Malfunction - Cylinder 1
• P0202 [1] Injector Circuit Malfunction - Cylinder 2
• P0203 [1] Injector Circuit Malfunction - Cylinder 3
• P0204 [1] Injector Circuit Malfunction - Cylinder 4
• P0205 [1] Injector Circuit Malfunction - Cylinder 5
• P0206 [1] Injector Circuit Malfunction - Cylinder 6