Ford Escape Hev 2006

• Recall 117048 [USA]: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "park" position, but the vehicle transmission may not actually be in the "park" gear position. if the vehicle is not in the "park" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. a vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
  Ford motor company (ford) is recalling certain model year 2001-2008 ford escape and mercury mariner vehicles manufactured march 31, 2001, to september 1, 2009. The affected vehicles are equipped with either a 2.3l or 3.0l engine and have had their cd4e transmission replaced with remanufactured one that was rebuilt between june 11, 2015 through july 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
  ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on october 23, 2015. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 15s28.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 117599 [USA]: Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
  The timken company (timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from january 22, 2015, to may 21, 2015, to be used as service parts on 2001-2012 ford escape, 2001-2011 mazda tribute, and 2005-2011 mercury mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.
  timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on may 21, 2015. Owners may contact timken customer service at 1-866-984-6536.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 105535 [USA]: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.
  Ford motor company (ford) is recalling certain model year 2005-2008 ford escape hybrid electric vehicles manufactured october 13, 2003, to june 20, 2008, and 2006-2008 mercury mariner hybrid electric vehicles manufactured june 10, 2005, to june 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.
  ford will notify owners, and dealers will inspect and replace the original motor electronics coolant (mec) pump with an improved brushless pump, free of charge. The recall is expected to begin on october 27, 2014. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 14s19.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 68760 [USA]: An improperly deployed airbag could result in serious injury.
  Marathon is recalling certain seat covers, brand superhides with part numbers 593, 594, 578, 960, 228, 228-09, 267-08, 333, 625, and 630, sold for use as aftermarket equipment for various passenger vehicles. These seat covers are made of heavier thread and are not compatible with seats containing side airbags. The heavier seat cover could interfere with full deployment of the airbag in the event of a crash.
  marathon will notify owners of record and replace the seat cover free of charge. The safety recall began on september 14, 2010. Owners may contact marathon at 1-800-735-2769.
  this recall only pertains to aftermarket marathon seat covers and has no relation to any original equipment installed on general motors, ford, chrysler, toyota, or nissan vehicles.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 36820 [USA]: If a fracture occurs, the powertrain will lose the ability to transmit torque to the drive wheels and the transmission will not hold the vehicle stationary when placed in the park position, which could result in a crash.
  On certain front wheel drive hybrid vehicles, the intermediate shaft may not have been properly heat treated and may fracture while the vehicle is being driven.
  dealers will inspect the drivetrain intermediate shaft and replace it if necessary. The recall began on october 23, 2006. Owners may contact ford at 1-800-392-3673.
  ford recall no. 06s44.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 60205 [USA]: After a period of continuous use on the high speed setting, lack of grease on the output shaft gear may cause the gear to distort or fracture during operation resulting in a loss of wiper function. inoperative wipers under inclement weather conditions could cause a crash due to impaired visibility.
  On certain trucks, passenger cars and sport utility vehicles, the windshield wiper motor may have been produced without grease being applied to the output shaft gear.
  dealers will inspect the wiper motor for the presence of grease and grease the wiper motor gears if necessary. The recall began on november 22, 2005. Owners may contact ford at 1-800-392-3673 or lincoln/mercury at 1-800-521-4140.
  ford recall no. 05s40. Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 2015438 [Canada]: Powertrain
  A safety defect may exist in vehicles in which remanufactured automatic transmissions were installed as service replacement parts. The shift lever bolt may not have been torqued to the proper torque specification. If the improperly torqued shift level bolt loosens and backs out, the shift lever may disengage from the transmission without warning, and the transmission may not respond to the shifter selection movement by the operator. This could result in the loss of transmission gear selection, and possible unintended vehicle movement, which would increase the risk of a crash causing injury and/or property damage. Correction: dealers will inspect, and if necessary, replace the shift lever assembly and/or the shift level bolt torqued to the proper specification.

  Show Content

• Recall 2014374 [Canada]: Engine
  On certain hybrid vehicles, the motor electronics coolant pump may wear out and fail, resulting in a loss of coolant flow and high temperature condition within the motor electronics system. This could result in a partial or full loss of motive power, resulting in a sudden stall-like condition while driving. An engine stall without warning while driving could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will affect repairs. Note: power steering and power braking system function would be unaffected in the event of such an occurrence.

  Show Content

• Recall 2006274 [Canada]: Powertrain
  On certain escape hybrid vehicles, the intermediate shaft used in the front wheel driveline may not have received adequate heat treat process during manufacturing. As a result, the intermediate shaft may fracture while the vehicle is being driven. If a fracture occurs the powertrain will lose the ability to transmit torque to the drive wheels and the transmission will not hold the vehicle stationary when placed in the park position. Correction: dealers will inspect and, if required, replace the intermediate shaft.

  Show Content

• Recall 2005356 [Canada]: Other
  On certain vehicles, the windshield wiper motor may have been produced without grease applied to the output shaft gear. After a period of continuous use on the high-speed setting, lack of grease may cause the gear teeth to distort and/or fracture during operation, resulting in the loss of wiper function. Correction: dealers will inspect and, if required, apply grease to the output shaft gear.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Pedestrian alert sounds investigation # DP22005

  Nhtsa received a petition on or about july 18, 2022, requesting that federal motor vehicle safety standard (fmvss) 141 be applied to all electric and hybrid vehicles operating in the united states. The petition can be reviewed at nhtsa.Gov under odi number 11486072.Fmvss 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 kg or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after march 1, 2021.The petitioner asserts that hybrid and electric vehicles to which the standard does not apply should be found to contain a safety defect. In support of the petition, the petitioner includes findings contained in a bill introduced in the house of representatives in 2009, the pedestrian safety enhancement act of 2009, h.R. 734, 111th cong. (2009). A related bill, the pedestrian safety enhancement act of 2010, became law in january 2011 (pub. L. 111-373). The petitioner requests that nhtsa require all electric and hybrid vehicles comply with fmvss 141, regardless of production date.The defect petition has been opened to evaluate the issue and determine whether to grant or deny the petition.The associated product list is not exhaustive and may contain vehicles that are equipped with pedestrian alert sounds.
  

  Show Content

• Electronic throttle body malfunction investigation # DP12006

  In a letter dated august 30, 2012, the north carolina consumers council (nccc) petitioned the national highway traffic safety administration (nhtsa) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (my) 2005 through 2012 ford escape vehicles. On october 2, 2012 the office of defects investigation (odi) opened a defect petition dp12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The nccc letter cites two complaints of stall while driving in my 2009 ford escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (dtc) P2111, throttle body stuck open, and P2112, throttle body stuck closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to ford, escape non-hybrid vehicles are equipped with electronic throttle body (etb) assemblies beginning with my 2009. Vehicles manufactured between june 22, 2009 and october 15, 2009 may contain contaminated printed circuit boards (pcb) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other dtcs would be generated and stored. Ford and its electronic throttle body supplier, delphi, modified the pcb manufacturing process and issued a technical service bulletin (tsb) 09-23-5. Vehicles produced after october 15, 2009 incorporated etbs manufactured with a pcb process that resolved this condition. Odis analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 rpm. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine rpm fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine rpms once the vehicle reaches a reduced speed to maintain approximately 900 rpm. Separately, odi received 59 complaints alleging incidents of engine stall while driving in model year (my) 2010-2011 ford fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning march 2012 and 14 complaints reported that the throttle body was replaced or dtcs associated with limp home modes. Additionally, ford issued tsb 10-21-6 addressing dtcs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary evaluation pe13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the voqs associated with the defect petition analysis.
  

  Show Content

On sunday may/23/2021 my car shut off suddenly with out warning after 3m of driving, the wrench orange lite came on, i was able to pull aside on the curb, turned off the car and waited a few minutes, i was able to turn the car back on, and the car restarted with out problem but the incident was there. When i got home i start looking on line for an explanation of what went wrong and i encounter that the 2006 ford scape hybrid has been recall for stalling problems, somehow my car is not part of the recall according with the vin number, but my car is a 2006 ford scape hybrid, i don't understand why my car its not part of the recall and i hope that it did not fall under the cracks and i hope more that my car will not get stall in the freeway and cause an accident. Please let me know if any additional information is need it

Dash lights go out at a fill tank of gas and when the vehicle is warmed up and some times. Stay off for a long time vehicle stay running and goes down the road .

Dash lights go out at a fill tank of gas and when the vehicle is warmed up and some times. Stay off for a long time vehicle stay running and goes down the road .

Knocking, knocking when accelerating, hesitation.

Knocking, knocking when accelerating, hesitation.

Abs failure. The car brakes may at times lock-up without notice. Transmission failure: the transmission acts as if it's in neutral when in both forward gear or reverse. Transmission appears to be in good repair but this issue persist. This issue appears to occur from a beginning acceleration such as putting car in reverse and accelerating or putting car in drive and accelerating. This also happens when you may be stopped at a traffic light and attempt to proceed only to have the car act as if it's in neutral. This slipping in and out of gear issue seems to only happen from a take off speed.

Abs failure. The car brakes may at times lock-up without notice. Transmission failure: the transmission acts as if it's in neutral when in both forward gear or reverse. Transmission appears to be in good repair but this issue persist. This issue appears to occur from a beginning acceleration such as putting car in reverse and accelerating or putting car in drive and accelerating. This also happens when you may be stopped at a traffic light and attempt to proceed only to have the car act as if it's in neutral. This slipping in and out of gear issue seems to only happen from a take off speed.

While driving at lower speeds and city speeds, abs light come on with service brake system message appears while driving and turning. Braking is tough and barely stops even with hard foot pressure on pedal. This is an ongoing problem that intermittently happens. Once you let the car sit for awhile (since you are scared of driving it), the braking system resets and problem is not seen for months...Until it occurs again. Inquiries to ford about problem estimate the cost of replacing cylinder, hcu, and bleeding brakes far exceeds the value of vehicle. Annoying as this brake problem was identified as a weakness of this car's braking system as far back as 2005! Why does ford not recall and fix a known problem in a timely manner? May have to scrap an otherwise excellent working vehicle because it is unsafe to drive and unsafe to fellow drivers since it may not reliably stop.

While driving at lower speeds and city speeds, abs light come on with service brake system message appears while driving and turning. Braking is tough and barely stops even with hard foot pressure on pedal. This is an ongoing problem that intermittently happens. Once you let the car sit for awhile (since you are scared of driving it), the braking system resets and problem is not seen for months...Until it occurs again. Inquiries to ford about problem estimate the cost of replacing cylinder, hcu, and bleeding brakes far exceeds the value of vehicle. Annoying as this brake problem was identified as a weakness of this car's braking system as far back as 2005! Why does ford not recall and fix a known problem in a timely manner? May have to scrap an otherwise excellent working vehicle because it is unsafe to drive and unsafe to fellow drivers since it may not reliably stop.

Common OBD-II Error Codes

• P0351 [1] Ignition Coil A Primary/Secondary Circuit Malfunction
• P0356 [1] Ignition Coil F Primary/Secondary Circuit Malfunction
• P0451 [1] Evaporative Emission Control System Pressure Sensor Range/Performance
• U2062 [1] U2062
• P0340 [1] Camshaft Position Sensor Circuit Malfunction (Bank 1)
• C1475 [3] C1475
• P0300 [1] Random/Multiple Cylinder Misfire Detected
• P0301 [1] Cylinder 1 Misfire Detected
• P0302 [1] Cylinder 2 Misfire Detected
• P0303 [1] Cylinder 3 Misfire Detected
• P0304 [1] Cylinder 4 Misfire Detected
• P0316 [1] Misfire Detected On Startup (First 1000 Revolutions)
• P2111 [1] Throttle Actuator Control System - Stuck Open
• P2112 [1] Throttle Actuator Control System - Stuck Closed