Ford Escape-hybrid-awd 2008

• Recall 117058 [USA]: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "park" position, but the vehicle transmission may not actually be in the "park" gear position. if the vehicle is not in the "park" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. a vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
  Ford motor company (ford) is recalling certain model year 2001-2008 ford escape and mercury mariner vehicles manufactured march 31, 2001, to september 1, 2009. The affected vehicles are equipped with either a 2.3l or 3.0l engine and have had their cd4e transmission replaced with remanufactured one that was rebuilt between june 11, 2015 through july 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
  ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on october 23, 2015. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 15s28.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 117609 [USA]: Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
  The timken company (timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from january 22, 2015, to may 21, 2015, to be used as service parts on 2001-2012 ford escape, 2001-2011 mazda tribute, and 2005-2011 mercury mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.
  timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on may 21, 2015. Owners may contact timken customer service at 1-866-984-6536.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 105539 [USA]: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.
  Ford motor company (ford) is recalling certain model year 2005-2008 ford escape hybrid electric vehicles manufactured october 13, 2003, to june 20, 2008, and 2006-2008 mercury mariner hybrid electric vehicles manufactured june 10, 2005, to june 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.
  ford will notify owners, and dealers will inspect and replace the original motor electronics coolant (mec) pump with an improved brushless pump, free of charge. The recall is expected to begin on october 27, 2014. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 14s19.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 104379 [USA]: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
  Ford motor company (ford) is recalling certain model year 2008-2011 ford escape and mercury mariner vehicles manufactured august 18, 2006, through september 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the electric power steering (eps) assist.
  ford will notify owners, and dealers will update the software for the power steering control module (pscm) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the pscm when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on july 18, 2014. Owners may contact ford customer service at 1-800-392-3673. Ford's number for this recall is 14s05.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 68766 [USA]: An improperly deployed airbag could result in serious injury.
  Marathon is recalling certain seat covers, brand superhides with part numbers 593, 594, 578, 960, 228, 228-09, 267-08, 333, 625, and 630, sold for use as aftermarket equipment for various passenger vehicles. These seat covers are made of heavier thread and are not compatible with seats containing side airbags. The heavier seat cover could interfere with full deployment of the airbag in the event of a crash.
  marathon will notify owners of record and replace the seat cover free of charge. The safety recall began on september 14, 2010. Owners may contact marathon at 1-800-735-2769.
  this recall only pertains to aftermarket marathon seat covers and has no relation to any original equipment installed on general motors, ford, chrysler, toyota, or nissan vehicles.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 2015438 [Canada]: Powertrain
  A safety defect may exist in vehicles in which remanufactured automatic transmissions were installed as service replacement parts. The shift lever bolt may not have been torqued to the proper torque specification. If the improperly torqued shift level bolt loosens and backs out, the shift lever may disengage from the transmission without warning, and the transmission may not respond to the shifter selection movement by the operator. This could result in the loss of transmission gear selection, and possible unintended vehicle movement, which would increase the risk of a crash causing injury and/or property damage. Correction: dealers will inspect, and if necessary, replace the shift lever assembly and/or the shift level bolt torqued to the proper specification.

  Show Content

• Recall 2014374 [Canada]: Engine
  On certain hybrid vehicles, the motor electronics coolant pump may wear out and fail, resulting in a loss of coolant flow and high temperature condition within the motor electronics system. This could result in a partial or full loss of motive power, resulting in a sudden stall-like condition while driving. An engine stall without warning while driving could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will affect repairs. Note: power steering and power braking system function would be unaffected in the event of such an occurrence.

  Show Content

• Recall 2014193 [Canada]: Steering
  On certain vehicles, a fault in the electric power steering (eps) system could result in an immediate loss of power steering assist without warning to the driver. This would unexpectedly increase the steering effort force necessary to steer the vehicle at lower vehicle speeds, which could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will affect repairs as necessary and will reprogram the eps controller with updated software. In the event that an eps fault occurs, this updated software would allow for continued eps function while displaying visual and audible warnings to the driver until the end of the drive cycle.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Pedestrian alert sounds investigation # DP22005

  Nhtsa received a petition on or about july 18, 2022, requesting that federal motor vehicle safety standard (fmvss) 141 be applied to all electric and hybrid vehicles operating in the united states. The petition can be reviewed at nhtsa.Gov under odi number 11486072. Fmvss 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 kg or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after march 1, 2021.On january 27, 2023, nhtsa opened defect petition (dp) 22-005 to evaluate the subject matter described in the petition. On june 24, 2023 and as supplemented on june 25, 2023, the petitioner notified nhtsa he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioners withdrawal, dp22-005 is closed. Closure of this dp does not represent a determination by nhtsa regarding the subject matter of the petition.
  

  Show Content

• Loss of power steering while driving investigation # DP15001

  On may 27, 2014, amended june 2, 2014, ford motor company (ford) submitted a defect information report (dir) to nhtsa describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (my) 2008 through 2011 ford escape vehicles equipped with electric power assisted steering (nhtsa 14v-284, ford 14s05). Fords dir described the defect condition as a poor signal to noise ratio [snr] in the torque sensor within the electric power assisted steering (epas) system [which] does not allow the pscm to determine the drivers steering input. When the system detects this fault condition, it transitions the epas system to the fail-safe/manual steering mode.Fords dir indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Fords remedy instructs dealers to check the power steering control module (pscm) for diagnostic trouble codes (dtcs) to determine the proper repair procedure. If no dtcs are present, dealers are to update the pscm and instrument cluster module software. The updated pscm software changes the torque sensor fault strategy so that the snr condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If dtcs indicating faults in the torque sensor, pscm or power steering motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (dtc B2278); or 2) replaces the steering column for faults related to the pscm (dtc B1342) or motor (dtc B2277).Continued in attachment pages
  

  Show Content

• Electronic throttle body malfunction investigation # DP12006

  In a letter dated august 30, 2012, the north carolina consumers council (nccc) petitioned the national highway traffic safety administration (nhtsa) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (my) 2005 through 2012 ford escape vehicles. On october 2, 2012 the office of defects investigation (odi) opened a defect petition dp12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The nccc letter cites two complaints of stall while driving in my 2009 ford escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (dtc) P2111, throttle body stuck open, and P2112, throttle body stuck closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to ford, escape non-hybrid vehicles are equipped with electronic throttle body (etb) assemblies beginning with my 2009. Vehicles manufactured between june 22, 2009 and october 15, 2009 may contain contaminated printed circuit boards (pcb) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other dtcs would be generated and stored. Ford and its electronic throttle body supplier, delphi, modified the pcb manufacturing process and issued a technical service bulletin (tsb) 09-23-5. Vehicles produced after october 15, 2009 incorporated etbs manufactured with a pcb process that resolved this condition. Odis analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 rpm. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine rpm fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine rpms once the vehicle reaches a reduced speed to maintain approximately 900 rpm. Separately, odi received 59 complaints alleging incidents of engine stall while driving in model year (my) 2010-2011 ford fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning march 2012 and 14 complaints reported that the throttle body was replaced or dtcs associated with limp home modes. Additionally, ford issued tsb 10-21-6 addressing dtcs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary evaluation pe13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the voqs associated with the defect petition analysis.
  

  Show Content

• Tire valve cracking investigation # PE08060

  On october 14, 2008, odi opened pe08-060 to investigate allegations of cracked and leaking snap-in tire valves in model year (my) 2007 vehicles manufactured by ford motor company.The valves were supplied to ford by topseal auto-parts, a subsidiary of the shanghai baolong automotive corporation in china.Valves made by topseal for aftermarket sale were the subject of two recent safety recalls by tech international (08t-018) and dill air controls (08t-028), the latter of which was investigated by odi in pe08-036 and ea08-022.The defect conditions addressed by the aftermarket tire valve recalls both involved inadequate resistance to ozone cracking due to issues with the supply of anti-ozonant chemicals to topseal for a period from july to mid-november 2006.The aftermarket valves were compounded with a blend of epdm and natural rubber, using a relatively low percentage of epdm (epdm provides inherent resistance to ozone cracking).Hence, the need for anti-ozonant chemicals and the problems with cracking when those chemicals were missing or out of specification in some lots of valves.Both recall campaigns involved inspection programs to identify and replace valves with visible surface cracking.Although the topseal valves supplied to ford also appear to have been affected by the anti-ozonant supply issues in mid to late-2006, ford indicated that its valves were made at a different topseal production line and were compounded with a higher percentage of epdm rubber to meet more stringent specifications from ford.Odis analysis of complaint and warranty data provided by ford showed that problems with cracked tire valves were significantly higher for my 2007 vehicles produced from december 2006 through march 2007.Ford responded by implementing changes in its material specifications for snap-in rubber tire valves and also increasing the quality and acceptance standards for valves imported for use in its vehicles.While the complaint and warranty claim rates are elevated for subject vehicles produced from december 2006 through march 2007, the rates of leaking valves are well below one percent of production for each of the peak months for all of the affected models.A substantial majority of the subject vehicles are equipped with tire pressure monitoring systems (tpms) which warn the driver when any tire pressures drops below 25 percent of recommended inflation pressure. As outlined in a letter to odi dated april 6, 2009, ford has agreed to send letters to owners of certain my 2007 and 2008 ford, lincoln and mercury vehicles to provide information about the cracking concern. Letters will be sent to owners of vehicles built from november 2006 through may 2007.Owners can opt for a free dealer inspection.Valves exhibiting surface cracks or air leakage related to ozone attack will be replaced by ford under its normal warranty terms.Ford expects to send the letter by approximately mid-may 2009. Based on the use of tpms in the majority of subject vehicles and the relatively low rates of repairs associated with leaking valves and resultant tire damage, odi believes that the actions ford has agreed to take will provide effective and expeditious resolution for vehicles that were built during the period when valves with inadequate resistance to ozone cracking were most likely to have been used in vehicle production.Further investigation of this matter would not be an efficient allocation of agency resources.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.The agency will continue to
  

  Show Content

The back liftgate glass on my 2008 ford escape separated from latch and exploded when closing.

Hard to steer the vehicle.

The loss of power steering that was reported as being fixed with ford recall # 14s05 is still happening and ford is not covering the cost of fixing it again.

The contact owns a 2008 ford escape hybrid. The contact stated that while driving at various speeds, the brake was applied however, was spongy and slow to respond. The abs warning light was illuminated. The regan brakes disable failure message was displayed. The vehicle was taken to an independent mechanic who referred the contact to a local dealer. The local dealer was not contacted. The vehicle was not diagnosed nor repaired. The manufacturer was not contacted. The failure mileage was 165,931.

My abs brake warning and my regular brake light come on and go off occasionally with a warning that says "regen brake system disabled". When this happens, it very difficult to brake, the brakes go almost to the floor before they engage and there is some sort of air leak because i can hear a leak in an air system of some kind. And when that started happening, the a/c stopped working and i heard a loud pitched whine coming from the vehicle. On the days there is no brake warning lights, the brakes still are not great and sometimes will start to stop the vehicle, then there is a kind of hiccup that happens where the pedal just goes to the floor while you are stopping, and not just as you begin braking. There are so many complaints on the web about people experiencing the exact same problems, i don't see why this has not been deemed a recall yet. Very dangerous!!!!

There is a major safety issue with the braking system. The brakes were getting soft (having to push all the way to the floor to get it to stop) a brake warning light then came on, i had a mechanic check it and he replaced all 4 brakes and rotors on it, a small improvement...Then the abs warning light came on.....It now brakes fine from speed until about 10 mph and then the brake pedal goes to the floor. Upon having the warning light scanned, it appears that the hcu (hydraulic control unit) needs replaced for a tune of $5000 plus. Upon more research there are many complaints on-line about this problem, unfortunately those of us that drive 13 year old cars typically cant afford such a repair bill for an obviously bad design flaw and must continue driving these dangerous vehicles because we have no choice. I'll be keeping my fingers crossed

The car show a message saying "stop safely now" and starts stalling and then suddenly turn off by itself. It can happen while driving in freeway or the street

Brakes are pedal is advancing towards the floor without any response until almost at the floor. Master cylinder was replaced and problem still exists. No codes evident, nor signs of defect. Spent entire day at the mechanic to no avail. Must use pumping brake s continually at reduced speeds from greater lengths to stop at appropriate time and location.

I started my vehicle and i got a warning beep saw the display saying power steering assist fault. My steering wheel was vibrating and a loud motor type noise was sounding. I would drive and i could feel the steering wheel shimmy while driving. The next day i started my car and display showed right away the power steering assist default. And i had no power steering from then on. Other 2008s had recalls for power steering but my vin was not on the list for recalls

Common OBD-II Error Codes

• P0A81 [2] Hybrid Battery Pack Cooling Fan 1 Control Circuit/Open
• P0A96 [2] Hybrid Battery Pack Cooling Fan 2 Control Circuit/Open
• C1478 [1] C1478
• C1479 [1] C1479
• C1480 [1] C1480
• C1481 [1] C1481
• B2278 [4] B2278
• P0715 [1] Input/Turbine Speed Sensor A Circuit Malfunction
• P0717 [1] Input/Turbine Speed Sensor A Circuit No Signal
• P0720 [1] Output Speed Sensor Circuit Malfunction
• P0721 [1] Output Speed Sensor Range/Performance
• P0722 [1] Output Speed Sensor No Signal
• P0451 [1] Evaporative Emission Control System Pressure Sensor Range/Performance
• P1A0C [1] P1A0C
• U2062 [1] U2062
• C1526 [1] C1526
• B2572 [1] B2572
• B1342 [1] ECU Is Defective
• B2277 [1] B2277
• P2111 [1] Throttle Actuator Control System - Stuck Open
• P2112 [1] Throttle Actuator Control System - Stuck Closed