2013 HINO CONVENTIONAL-TRUCKS-W-JO8Hino Conventional-trucks-w-jo8 2013

Vehicle Details: Service Bulletins

Below you will find all available information on the 2013 HINO CONVENTIONAL-TRUCKS-W-JO8, manufacturered by Hino Motors Canada, Ltd.

ManufacturerKnown WMI(s)Fuel Type
HINO2AY 5PV JHA JHB
HINO VIN Decoder

Use the box here to look up VINs from HINO as well as other manufacturers

#
Frequently Asked Questions
  • Where is the 2013 HINO CONVENTIONAL-TRUCKS-W-JO8 produced?
     - The 2013 HINO CONVENTIONAL-TRUCKS-W-JO8 is produced in, Canada.
NHTSA Mandated Recalls

No recalls could be found for this vehicle. To ensure accuracy and for your safety, do a free VIN recall check here or here [USA] - UK - Canada.

Recalls are also available on the Complaints page
Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • TT-16-014 - BACK OVER PREVENTION: General - dtc P20B2 coolant cutoff valve diagnostic - most scr (selective catalyst reduction) coolant cutoff valves received through warranty return do not reveal any faults when tested. Please follow the checks outlined below before replac
  • TT-16-013 - EQUIPMENT: Engine - cam housing bolt torque update. The procedure for installing the rocker shaft bolts into the cam housing has been updated. It is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before inst
  • TT-16-009 - FUEL SYSTEM, GASOLINE: General - 2011-17 conventional trucks or 2013-17 coe trucks. Current production def injectors contain enhancements including improvements to the aluminum housing. When replacing the def injector, it is necessary to install the complete def
  • TT-16-003 - FUEL SYSTEM, GASOLINE: General - def pump diagnostic tips - supersedes tt-15-025 def pump diagnostic tips conventional trucks equipped with a j05 engine.
  • TT-16-001 - EQUIPMENT: Conventional trucks (238, 258, 268 or 338) during service of the exhaust aftentreatment system, the technician may find the "burner status" shown in dxii remains at "" request (accumsoot)" or "#3 intial check (preparegen)" even after the dp
  • TT-15-031 - VEHICLE SPEED CONTROL:CRUISE CONTROL: General - conventional trucks (238, 258, 268, or 338) and 2012 - 2016 coe trucks (195, 195h) the tech tip below is to set or change road speed on a hino conventional or coe truck. The below procedure and screen shots were taken from a conve
  • TT-15-013 - EQUIPMENT ADAPTIVE/MOBILITY: Intake and exhaust - conventional trucks (238, 258, 268, or 338) and 2013 - current coe (cab over enginef) trucks. To provide a better determination of a dpf's internal condition, a special service tool (sst) has been developed. An explanat
  • SB-16-029 - EQUIPMENT: Service manual update - correction of workshop manual for hino300 series detailed explanation of the fuel pipe installation
  • SB-16-022 - BRAKES (PWS): General - conventional trucks (238, 258, 268, or 338) a subject vehicle may experience an external fuel leak from the burner atomization module assembly, specifically the fuel pressure regulator. This repair procedure outlines replacement o
  • SB-16-020 - BRAKES (PWS): Engine - coe trucks (155, 155h, 195, or 195h) an enhanced fuel cut valve is available to address a potential sticking coindition that results in excess residual pressure in the dosing injector (7th injector) supply pipe. A stickingf fuel cu
  • SB-16-018 - BACK OVER PREVENTION: General - cab over engine trucks 155, 155h, 195, or 195h enhanced software is available for the vcs module to correct false detection of dtc P161F-malfunction of act uator relay, when a low voltage condition is present.
  • SB-16-010 - EQUIPMENT: Correction of workshop manual for 2008-17 correction of the inspection of the dpr filter.
  • SB-16-006 - BRAKES (PWS): Conventional trucks (228, 258, 268, or 338) suspension. Some vehicles built before january 2016 and equipped with a leaf spring rear suspension may experience a dislodged or missing spring pad. As an enhancefment, the rear axle leaf spring
  • SB-16-005 - EQUIPMENT: Correction of workshop manual for hino600 series addition of deta iled explanation of the fuel pipe installation.(service manual update)
  • SB-16-004 - EQUIPMENT: Hino 300 series with hv - correction of workshop manual for hino300 series correction of clutch learning
  • SB-16-001 - EQUIPMENT: Correction of workshop manual for hino coe correction of clearance between the front leasf spring bracket pin and bushing - 155, 195, 155h, 195h. Correction of clearance betweeen the front leaff spring bracket pin and leaf spring bushing.
  • SA-16-026 - EQUIPMENT: If a 2013 - 17 coe model 195h is encountered with a will not move in any gear condition and any combination of dtc's P0706, P0756, P0761, P1604, please perform the following for engineering review.
  • SA-16-023 - FUEL SYSTEM, GASOLINE: Def injec tor assembly replacement. The following service alert is to advise about the def (diesel exhaust fluid) injector if it's being replaced under warranty. The recent changes made to the def injector include enhancements to the alumi
  • SB-16-007 - EQUIPMENT: Conventional trucks (238, 258, 268, or 338) if dtc (diagnostic trouble code) P0611: fuel injector driver charge circuit - circuit low has set in the engine ecu (electronic control unit) and the workshop manual diagnostic procedure has led t
  • TT-15-007 - ENGINE (PWS): Vehicle control system (vcs) programming procedure 2013-15 coe diesel or hybrid trucks has changed with dx2 updates.
  • TT -15-006 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : P200C diagnostic procedure model year conventional trucks. The following diagnostic procedure should be followed for a unit with dtc P2000c. This procedure will check the integrity of the doc and the scr catalysts. If the P200C is set, the
  • SB-15-037 - EQUIPMENT: Correction of workshop manual for hino600 servies correction of cam height standard value. Hino 238, 258, 268, 338, 358
  • SB-15-036 - EQUIPMENT: Radiator reservoir tank hose replacedment conventional trucks (238, 258, 268, or 338) built between 08/01/2012 and 07/02/2015
  • SB-15-032 - EQUIPMENT: Correction of workshop manual for 2011-2014 troubleshooting information and inspection procedure of the dtc/P2030 were revised burner control system (bcu)
  • SB-15-031 - EQUIPMENT ADAPTIVE/MOBILITY: Conventional trucks (238, 258, 268 or 338) and coe (cab over engine) trucks (195, 195h) foreign debris in the def (diesel exhaust fluid) tank may cause the scr (select calalyst reduction) system to malfunction. This can result in dtc's (dia
  • SB-15-028 - EQUIPMENT ADAPTIVE/MOBILITY: Suspension - a coe if equipped with a severe duty body application may experience excessive body roll or poor handling at highway speeds. This tsb (technical service bulletin) outlines an inspection procedure highlighting approved body inst
  • SB-15-019 - EQUIPMENT: Conventional cracked hood repair. Reinforcement brackets and fiberglass repair methods have been made available to address hood crack concerns. In the event a subject vehicle experiences cracking of the hood near the hinges, this repair pr
  • SB-15-016 - EQUIPMENT: New parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. This bulletin provides instructions for installing longer manifold studs at the #4 cylinder location.
  • SB-15-013 - EQUIPMENT: Correction of workshop manual for 2013-2015 (hino155, 155h, 195, 195h ) addition of overhaul of the power steering gear) the following is to inform you of the above caption. This service data should be attached to the relevant pages of the
  • SB-15-002 - EQUIPMENT: Correction of workshop manual for year 2013-15 (revison of troubleshooting procedure for the dtc P2123) the following is to inform you of the above caption. This service data should be attached to the relevant pages of the workshop manuals
  • SA-15-047 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: A def system equipped truck may come in to the dealer with a coimplaint that the mil is on and dtc P142A is stored in the dcu. This dtc can set when the pump temperature sensor signal is out of the expected range when coimpared to other tem
  • 15-027 - POWER TRAIN:AUTOMATIC TRANSMISSION: Hino conventional trucks equipped with an allison transmission. The information contained below outlines scenarios that may not account for all configurations and should be utilized as a general guideline to assist in the integration of int
  • AA0F0 - FUEL SYSTEM, DIESEL: Ecu diesel particulate reduction (dpr) enhancement dpr clogging may occur due to an increase in the amount of soot in the exhaust gas as a result of engine component degradation. In order to reduce the soot in the exhaust gas during this si
  • 10-001 (2) - WHEELS: Correction to j08e engine workshop manual. Starter assembly mounting nuts torque correction.
  • SB-05-008 - EQUIPMENT ADAPTIVE/MOBILITY: This document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
  • SB-05-007 - ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PIPES, HOSES, AND FITTINGS: This document is to inform dealers of the design change on the water pipe for the j08e engine models listed below.
  • 167-B1812-03 - EQUIPMENT: Sb-18-034 conventional unification of part number workshop manual correction
  • 167-R1808-01 - ELECTRICAL SYSTEM:SOFTWARE: Conventional ecu, dcu, vcs software conventional ecu, dcu, vcs software update and emission label installation
  • 167-B1808-01 - ENGINE (PWS): Sa-18-012 P0300-series diagnostic
  • 167-B1804-01 - ENGINE (PWS): Sb-18-006 the subject vehicle may experience a concern where the starter motor fails to engage due to corrosion that
  • 167-B1803-01 - EQUIPMENT: Sb-17-037 combination meter workshop manual addition. We added a procedure of the trouble shooting of the combination meter.
  • 167-T1411-12 - ELECTRICAL SYSTEM:SOFTWARE: Tt-14-011 11my-14my conventional truck ? Naps regen will not complete. The burner control module (bcu) judges dtc?S P2441 (cav stuck), P2300 (ignition coil failure) and P060C (bcu temp sensor failure) on burner start up, if one of the faul
  • 167-T1409-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Tt-14-004 exhaust control valve adjustment procedure
  • 167-T1612-12 - ENGINE (PWS): Tt-16-013 the procedure for installing the rocker shaft bolts into the cam housing has been updated. It is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before installing them. The torque specifi
  • 167-T1605-12 - POWER TRAIN: Tt-16-003 subject vehicles may exhibit a mil lamp on with reduced engine power due to a fault within the scr (selective catalytic reduction) system. If dtc's (diagnostic trouble codes) related to the def (diesel exhaust fluid) pump set, it
  • 167-T1522-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Tt-15-026 subject vehicles may exhibit a mil lamp on with reduced engine power due to a restriction in the exhaust system such as a plugged dpf. The technician may find dtc?S (diagnostic trouble codes) such as P244B, P141F, P226C, and p029
  • 167-T1521-12 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Tt-15-025 subject vehicles may exhibit a mil lamp on with reduced engine power due to a fault within the scr (selective catalytic reduction) system. If dtc?S (diagnostic trouble codes) related to the def (diesel exhaust fluid) pump set, it
  • 167-T1514-12 - STRUCTURE:BODY: Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
  • 167-T1513-12 - POWER TRAIN: Tt-15-014 the transmission dtc?S P0974 and P0986, may be found on 12my-15my coe models. There could also be a complaint of low power and erratic shifting. These diagnostic codes may be set due to low voltage between the transmission case an
  • 167-T0706-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 07 - 006 voltage drop test
  • 167-B1312-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. All models
  • 167-B1621-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-010 correction of the inspection of the dpr filter.
  • 167-T1508-12 - ENGINE (PWS): Tt-15-008 conventional expected values
  • 167-B1529-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-032 troubleshooting information and inspection procedure of the dtc/P2030 were revised.
  • 167-B1528-12 - EQUIPMENT:ELECTRICAL: Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. This can result in dtc?S (diagnostic trouble codes) P20E8 or P20E9 - def pressure abnormality. An inlet
  • 167-B1523-12 - ENGINE AND ENGINE COOLING: Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
  • 167-B1521-12 - SUSPENSION: Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
  • 167-B1515-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE: Sb-15-016 new parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. This bulletin provides instructions for installing longer manifold studs at the #4 cylinder location.
  • 167-B1511-12 - STEERING: STEERING WHEEL/HANDLE BAR: Sb-15-011 the following tsb (technical service bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
  • 167-B1510-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated e
  • 167-B1415-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?S P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
  • 167-B1426-12 - STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS: Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised p
  • 167-B1423-12 - EQUIPMENT:ELECTRICAL: Sb-14-005 2011my-2015my conventional keyless entry programming
  • 167-B1423-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-005 2011my-2015my conventional keyless entry programming
  • 167-T1303-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-003 injection quantity test 11 thru 14my
  • 167-T1202-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 12-001 recording the burner event log (bel) on 11-13my trucks
  • 167-P1602-12 - ENGINE (PWS): 13-008 injection pump drive case. Please note the following part number changes to the injection pump bearing case. Not replacing the correct replacement parts will result in major engine damage. The hino ordering system has been modified

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.