2011 HINO Nv8jHino Nv8j 2011

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2011 HINO Nv8j.

ManufacturerKnown WMI(s)Fuel Type
HINO
HINO VIN Decoder

Use the box here to look up VINs from HINO as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2011 HINO Nv8j?
     - There are 4 recall(s) for the 2011 HINO Nv8j, additional information is below.
NHTSA Mandated Recalls
  • Recall 134831 [USA]: Excessive wear of the cylinders can result in engine failure, increasing the risk of a crash.

  • Recall 92199 [USA]: If the b+ circuit shorts to ground, it may lead to a fire.

  • Recall 85179 [USA]: In the event that the rear tank air pressure was depleted, braking function would be lost and the automatic engagement of the spring brakes will not occur, possibly resulting in a crash.

  • Recall 2016421 [Canada]: Brakes

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • 167-T1001-12 - STRUCTURE: Improper body u-bolt installation on right side, near fuel lines.
  • TT-14-033 - ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION: When replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
  • TT-14-017 - EQUIPMENT: Bendix air dryer service
  • TT-14-016 - EQUIPMENT ADAPTIVE/MOBILITY: Exhaust combustion chamber with loose insulation
  • SB-14-020 - EQUIPMENT ADAPTIVE/MOBILITY: When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
  • SB-14-014 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not complete.
  • SB-14-013 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Dpr damage, "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
  • 14-002 - EQUIPMENT: Coe hybrid safety equipment, tools and practices
  • TSB-14-025 - EQUIPMENT: Subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes) setting i
  • SB-15-010 - EQUIPMENT ADAPTIVE/MOBILITY: Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated egr valve h
  • 10-001 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : The following is to inform you of the correction made to the workshop manuals listed below. Please add this bulletin to the relevant pages (listed below) within your workshop manuals.
  • HINO 12-004 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Subject vehicles:
  • 167-T1406-12 - ELECTRICAL SYSTEM: 14-002 electrical issues or false starter engagement due to coolant intrusion into junction box
  • 167-T1603-12 - ELECTRICAL SYSTEM: Tt-16-001
  • 167-B1001-12 - FUEL SYSTEM, GASOLINE: Sb ? 10 - 003 this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel filter.
  • 167-T1514-12 - STRUCTURE:BODY: Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
  • 167-T0706-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 07 - 006 voltage drop test
  • 167-B1312-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. All models
  • 167-B1311-12 - SEATS: 13-014 an audible seat squeak may occur from the driver seat and/or single occupant passenger seat while driving over rough roads. This audible squeak may be occurring because of contact between the seat back frame and the seat base assembl
  • 167-B1308-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-010 correction of workshop manuals. Hint: in case the dtc P204F has being recorded in the engine ecu, but no dtc has been detected in the dcu, it is safe to think that power supply to the dcu was interrupted before the dtc was recorde
  • 167-B1307-12 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL): 13-008 design change of the idler gear case and idler gear bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idle
  • 167-B1306-12 - FUEL SYSTEM, DIESEL: 13-007 correction of workshop manuals. Addition of cautions for filling the def. (the actions to be taken if diesel fuel has been mistakenly added into the def tank.)
  • 167-B1305-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-006 correction of workshop manual. Correction of the terminals to be inspected in the diagnosis procedure of can communication line. (for dtc U0101)
  • 167-B1304-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-005 correction of workshop manual. Correction of maintenance interval for dpr filter and def filter element in the workshop manual.
  • 167-B1103-12 - ENGINE (PWS): Sb-11-005 information and procedure for checking and cleaning of the breather hose on the def tank. The breather hose can clog up with crystallized def, which can cause the def to overflow from the tank when filling and not allow the tank t
  • 167-B1101-12 - FUEL SYSTEM, OTHER: Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
  • 167-B1626-12 - FUEL/PROPULSION SYSTEM (PWS): Sb-16-022 a subject vehicle may experience an external fuel leak from the burner atomization module assembly, specifically the fuel pressure regulator. This repair procedure outlines replacement of the fuel pressure regulator seals while t
  • 167-B1625-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-021 correction of workshop manual for hino600 series correction of electrical wiring diagram
  • 167-B1621-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-010 correction of the inspection of the dpr filter.
  • 167-B1619-12 - SERVICE BRAKES, HYDRAULIC: Sb-16-006 some vehicles built before january 2016 and equipped with a leaf spring rear suspension may experience a dislodged or missing spring pad. As an enhancement, the rear axle leaf spring hanger design has been changed to eliminate the
  • 167-B1618-12 - FUEL/PROPULSION SYSTEM (PWS): Addition of detailed explanation of the fuel pipe installation.
  • 167-T1429-12 - ENGINE (PWS): Tt-14-033 when replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have
  • 167-T1416-12 - SERVICE BRAKES, AIR: Tt-14-017 the bendix ad-is (p/n: k154348) air dryer on air brake equipped vehicles contains several serviceable components. This replacement purge valve can eliminate the need to replace the whole air dryer assembly. These serviceable c
  • 167-T1415-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Tt-14-016 during service of the exhaust aftertreatment system, the technician may visually find that the insulation within the outer shell of the combustion chamber is pushing out or loose. In the event that loose insulation is found, it is
  • 167-B1602-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-16-015 enhanced dcu (dosing control unit) software has been released.Illumination of the check engine light. The dcu may falsely detect an issue and record any of the 3 following dtc?S in the dcu. P142A(def pump temperature sensor - out
  • 167-B1601-12 - FUEL SYSTEM, GASOLINE: Sb-16-007 if dtc(diagnostic trouble code) P0611:fuel injector driver charge circuit - circuit low has set in the engine ecu(electronic control unit) and the workshop manual diagnostic procedure has led to ecu replacement, an enhanced engine
  • 167-B1529-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-032 troubleshooting information and inspection procedure of the dtc/P2030 were revised.
  • 167-B1528-12 - EQUIPMENT:ELECTRICAL: Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. This can result in dtc?S (diagnostic trouble codes) P20E8 or P20E9 - def pressure abnormality. An inlet
  • 167-B1523-12 - ENGINE AND ENGINE COOLING: Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
  • 167-B1521-12 - SUSPENSION: Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
  • 167-B1518-12 - STRUCTURE:BODY: Sb-15-019 reinforcement brackets and fiberglass repair methods have been made available to address hood crack concerns. In the event a subject vehicle experiences cracking of the hood near the hinges, this repair procedure should be used
  • 167-B1513-12 - EQUIPMENT: Sb-15-014 correction of workshop manual for 2011my-2014my (addition and correction of burner system)
  • 167-B1510-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated e
  • 167-B1504-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc P0421)
  • 167-B1503-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc P2123)
  • 167-B1416-12 - FUEL SYSTEM, GASOLINE: Sb-14-013 "dpr damage", "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to red
  • 167-B1415-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?S P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
  • 167-B1414-12 - STRUCTURE:BODY:HOOD: Sb-14-020 when replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
  • 167-B1426-12 - STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS: Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised p
  • 167-B1423-12 - EQUIPMENT:ELECTRICAL: Sb-14-005 2011my-2015my conventional keyless entry programming
  • 167-B1420-12 - EQUIPMENT:ELECTRICAL: Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not
  • 167-B1419-12 - EQUIPMENT:MECHANICAL: Sb-14-009 during inspection of one of the subject vehicles, the technician may notice loose or missing retainer nuts or bolts on the no.1 cross member (directly behind the front bumper). In the event that loose nuts are found, it will be ne
  • 167-B1423-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-005 2011my-2015my conventional keyless entry programming
  • 167-B1420-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not
  • 167-B1419-12 - EQUIPMENT:MECHANICAL: Sb-14-009 during inspection of one of the subject vehicles, the technician may notice loose or missing retainer nuts or bolts on the no.1 cross member (directly behind the front bumper). In the event that loose nuts are found, it will be ne
  • 167-B1403-12 - ELECTRICAL SYSTEM: Sb-14-016 in the event that one of the subject vehicles is driven while the abs warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an abs warning lamp illuminated can lead to ov
  • 167-B1402-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-007 procedure for auto regeneration is possible but not manual regeneration.
  • 167-B1401-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-029 correction of workshop manual for 2011 - 2015 my. Troubleshooting information and inspection procedures for the dtc P2201 and P2214 were revised.
  • 167-B1408-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-028 correction of workshop manual for 2011- 2015 my. Troubleshooting information and inspection procedure of the dtc/P207F were revised.
  • 167-B1407-12 - ELECTRICAL SYSTEM: Sb-14-025 subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes)
  • 167-B1408-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-028 correction of workshop manual for 2011- 2015 my. Troubleshooting information and inspection procedure of the dtc/P207F were revised.
  • 167-B1407-12 - ELECTRICAL SYSTEM: Sb-14-025 subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes)
  • 167-R1404-12 - FUEL SYSTEM, DIESEL: Rcb-005-14 when a subject vehicle is operated at low temperatures, the def (diesel exhaust fluid) in the def hose may freeze, which may cause the on-board diagnostic system to work improperly, and may cause the mil (malfunction indicator la
  • 167-R1401-12 - FUEL SYSTEM, DIESEL: Rcb-004-13 when a subject vehicle is operated at low temperatures, the def (diesel exhaust fluid) in the def hose may freeze, which may cause the on-board diagnostic system to work improperly, and may cause the mil (malfunction indicator la
  • 167-T1303-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-003 injection quantity test 11 thru 14my
  • 167-T1301-12 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: 13-001 scr coolant hose clamp.
  • 167-T1202-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 12-001 recording the burner event log (bel) on 11-13my trucks
  • 167-T1201-12 - FUEL SYSTEM, GASOLINE: 12-004 "exhaust gas temp" (dpr outlet) reading error
  • 167-B1420-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not
  • 167-B1419-12 - WHEELS:LUGS/NUTS/BOLTS: Sb-14-009 during inspection of one of the subject vehicles, the technician may notice loose or missing retainer nuts or bolts on the no.1 cross member (directly behind the front bumper). In the event that loose nuts are found, it will be ne
  • 167-B1416-12 - ENGINE (PWS): Sb-14-013 "dpr damage", "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to red
  • 167-B1414-12 - EQUIPMENT ADAPTIVE/MOBILITY: Sb-14-020 when replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
  • 167-B1203-12 - ELECTRICAL SYSTEM:IGNITION: Sb-12-002 flame temperature sensor replacement guidelines. 2. Condition: many flame temperature sensors are being replaced for burner failure (as shown below) but in many cases the sensor itself is not the issue. Please follow the guidelin
  • 167-B1202-12 - SUSPENSION:MULTIPLE AXLE:TORQUE ARM: Sb-12-001 correction of 2011my workshop manual (addition of tightening torque for def injector mounting bolt)
  • 167-B0803-12 - WHEELS:LUGS/NUTS/BOLTS: Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
  • 167-B0602-12 - ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER: Sb ? 06 - 002 fuel filter usage. This bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
  • 167-B0601-12 - ENGINE AND ENGINE COOLING: Sb ? 06 - 001 design change of engine oil cooler housing. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retentio
  • 167-B0508-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
  • 167-B0506-12 - ENGINE (PWS): Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
  • 167-B0505-12 - EQUIPMENT ADAPTIVE/MOBILITY: Sb ? 05 - 007 design change of water pipe for j08e
  • 167-B0504-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
  • 167-B0503-12 - ENGINE (PWS): Sb ? 05 - 010 correction to workshop manuals for the j08e engine. A) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. C) r
  • 167-B0502-12 - EQUIPMENT: Sb - 05 - 004 speedometer recalibration. This document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. Tire size change, rear carrier ratio change).
  • 167-B0501-12 - ENGINE (PWS): 05 - 011 corrections to workshop manuals for j08 engines. The standard gap between ends of the second piston ring and the oil ring.
  • 167-R1504-12 - ELECTRICAL SYSTEM:SOFTWARE: Scb-006-15 1) dpr system (diesel particulate regeneration) manual regeneration may not complete; this occurs when the bcu temporally detects sticking of the cav (combustion air valve). This mis-detection will cause regeneration to be suspen
  • 167-R1502-12 - ENGINE (PWS): Aa0f0 dpr clogging may occur due to an increase in the amount of soot in the exhaust gas as a result of engine component degradation. In order to reduce the soot in the exhaust gas during this situation, even when the engine components are
  • 167-R1305-12 - ELECTRICAL SYSTEM:IGNITION: Rcb-001-13 when soot accumulates on the igniter surface, the burner ignition may perform improperly, which may cause the mil (malfunction indicator lamp) in the instrument cluster of the vehicle to turn ?On?. To promote improved ignition du
  • 167-R1304-12 - ENGINE (PWS): Rcb-006-11 during extreme below freezing ambient temperatures, the diesel exhaust fluid (def) may begin to freeze in the supply or return line coming from the def tank. This situation may result in illumination of the malfunction indicator
  • 167-R1303-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Rcb-007-11 during below freezing ambient temperature operation, condensation may develop in the exhaust gas recirculation (egr) inlet pipe and egr valve. When the engine is shut off, this condensation may freeze. Upon a cold engine restart,
  • 167-R1302-12 - ENGINE (PWS): Rcb-002-13 ecu enhancement. During vehicle operation, the malfunction indicator lamp (mil) may illuminate and/or the vehicle will experience reduced power.
  • 167-P1602-12 - ENGINE (PWS): 13-008 injection pump drive case. Please note the following part number changes to the injection pump bearing case. Not replacing the correct replacement parts will result in major engine damage. The hino ordering system has been modified
  • RCB-001-13 - ELECTRICAL SYSTEM:IGNITION: Hino: soot accumulates on the igniter. Burner ignition could perform improperly. Replacement of the diesel particulate regeneration (dpr) igniter plugs. *kb
  • RCB-006-11 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Hino: in below freezing ambient temperatures the diesel exhaust fluid (def) may freeze in the supply. Installing the def line cover kit installation should correct the issue. *kb
  • RCB-009-12 - ELECTRICAL SYSTEM:SOFTWARE: Hino: software update for burner control unit (bcu). Ignition of the burner system may perform improperly and cause a mil light to illuminate in the instrument cluster. *kb
  • RCB-008-12 - ELECTRICAL SYSTEM:SOFTWARE: Hino trucks: malfunction indicator lamp (mil) possibly illuminating during cold temperatures. Software update for the dosing control unit (dcu) could solve this problem. *kb
  • RCB-007-11 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Hino trucks: condensation that develops when the vehicle is running on the exhaust gas recirculation (egr) may freeze during below freezing temperatures causing the malfunction indicator lamp (mil) to illuminate. *kb
  • RCB-002-13 - ELECTRICAL SYSTEM:SOFTWARE: Hino trucks: malfunction indicator lamp (mil) may be illuminating. Vehicle may also experience reduced power. Performing a software enhancement should correct this problem. *kb

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.