Mercedes-benz Ml55 2002

• Recall 3101 [USA]: The control arm could fail, increasing the risk of a crash.
  Vehicle description: passenger vehicles. The left front upper control arm may not meet the specified strength requirements.
  dealers will replace the left front upper control arm. Owner notification began september 29, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact mercedes-benz at 1-800-367-6372.
  also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Brake lamp switch failure. investigation # PE10050

  Odi opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (bls) operates the stop lamps, a second set (ewm) controls the shift interlock system, and a third set (bs) is used by an on-board diagnostic (obd) system to monitor switch operation.The cruise control monitors the bls signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the obd system to detect a switch fault.When a fault is detected a malfunction indication lamp (mil) is illuminated (driver alert), a diagnostic trouble code (dtc) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to odis january 2011 information request letter, mb explained its assessment of switch failures which was based primarily on evaluation of field return failures.Mb identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to mbs analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance mb claims that bls contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the obd system, resulting in a dtc and subsequent replacement.Electrical contact failures of the bs and ewm contacts result in a dtc also, and ewm contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly mb maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.Mb determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the bls contacts and can cause the internal plastic components to melt.In one scenario overheated bls contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its march 31, 2011 defect notification, mb stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11v-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 m-class and model year 2000 - 2004 m-class amg vehicles.Owner notification letters will be mailed to consumers in september 2011.This action taken by mb is sufficient to resolve the issues raised by this investigation.
  

  Show Content

• Brake line chafe investigation # EA08009

  Analysis of complaints to odi and mercedes and warranty claim data submitted by mercedes indicates that the alleged defect has occurred at a low rate (36.5 complaints per 100,000 vehicles and 0.29 percent warranty claim rate), with no discernable defect trend indicating that the rate of chafing related brake line failures is increasing.There have been no new complaints since january 2009.When the analysis is limited to incidents of brake line leakage that resulted in allegations of reduced brake effectiveness, the rate drops even further (22.3 complaints per 100,000 vehicles and 0.04 percent warranty claim rate). Mercedes provided data showing that in the rare instances when chafing did progress to brake line leakage the driver would be immediately alerted to a problem by illumination of the bright yellow esp/bas warning lamp and changes in brake pedal feel.Continued operation with a leaking brake line would result in illumination of the bright red brake warning lamp and an audible chime due to low master cylinder reservoir level. Continued operation with the brake warning lamp illuminated would ultimately drain the reservoir for the affected circuit, resulting in loss of the circuit and an approximately 80% increase in stopping distances. Surveys conducted by odi and vrtc indicate that routing anomalies may be more common than the complaint and warranty data suggest for the subject line bundle, with line contact or other routing anomaly noted in 13 of 51 vehicles surveyed by odi and vrtc (25.5%).While evidence of contact between the fuel line and subject brake in a particular vehicle is not necessarily predictive of eventual line failure/leakage, significant chafing wear was noted in two survey vehicles (3.9%).To address concerns with line routing and ensure that lines with evident chafing do not progress to a leak condition, mercedes will conduct an owner notification program instructing owners to bring the vehicles to a dealer for a free inspection and repair.Lines that do not have a spacer (rubber grommet or omega-clip) between the subject fuel and brake lines will have an omega-clip spacer installed to ensure adequate clearance between the lines.Brake lines with chafe marks will be replaced. Accordingly, this investigation has been closed. The closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist. The agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted. For additional information regarding this engineering analysis refer to the ea08-009 closing report.
  

  Show Content

• Brake line rupture investigation # PE08002

  There is no summary currently available
  

  Show Content

While driving 40 mph my abs light shown up and all 4 tires lock up. Almost cause an accident. *tr

Tl* the contact owns a 2002 mercedes benz ml55. While driving 65 mph, the contact stated that the brake stability control activated without warning, causing the vehicle to idle abruptly. The vehicle was taken to a private mechanic who performed a diagnostic test which concluded that the yaw rate censor failed and needed to be replaced. The dealer informed the contact that there were no related recalls. The manufacturer was not aware of the failure. No repairs were performed. The current and failure mileages were 70,000. The vin was unavailable.

Common OBD-II Error Codes

• U1454 [1] U1454
• C1200 [1] ABS Inlet Valve Coil LF Circuit Short To Battery
• C1208 [1] ABS Inlet Valve Coil Rear Circuit Short To Battery