Mercedes-benz Slc 43 Amg 2017

• Recall 162450 [USA]: Failure of the ecall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
  Mercedes-benz usa, llc (mbusa) is recalling certain 2016 - 2021 cla-class, gla-class, gle-class, gls-class, slc-class, a-class, gt-class, c-class, e-class, s-class, cls-class, sl-class, b-class, glb-class, glc-class, and g-class vehicles. Please refer to the part 573 report for specific vehicle model details. The software design of the communication module may fail to communicate the correct vehicle location for the emergency call system (ecall) in the event of a crash.
  mbusa will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (ota) update, free of charge. The recall began march 12, 2021. Owners may contact mbusa customer service at 1-877-762-8267. Mbusa's number for this recall is 2021020025.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 122973 [USA]: If brake pads are constantly applied over long periods of driving, the brake components may heat up, affecting braking performance and increasing the risk of a crash. additionally, the dragging brakes may overheat, increasing the risk of a fire.
  Mercedes-benz usa, llc (mbusa) is recalling certain 2015 slk 250, 2016 slk 350, 2016-2017 slc 300, and 2017 slc 43 amg vehicles. In these vehicles, the electronic stability control (esc) system software may incorrectly keep the brakes slightly applied.
  mbusa will notify owners, and dealers will update the software for the esc system, free of charge. The recall began june 9, 2017. Owners may contact mbusa customer service at 1-800-367-6372.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall R/2017/157 [UK]: Brakes may overheat creating a risk of smoke and/or fire
  The software for the electronic stability program (esp) is faulty. The fault could lead to a low residual pressure in the hydraulic system so the brakes are applied and gain heat. This increased heat will apply the brakes further and could adversely affect the brake fluid. Fire in the wheel housing cannot be ruled out.
  recall the vehicles that are likely to be affected and update the software for the esp.

  Show Content

• Recall R/2020/243 [UK]: Engine control unit software to be updated
  Improve the vehicle emissions via software updates.
  update the relevant control unit?S software and if necessary replace the nox sensors.

  Show Content

• Recall R/2020/011 [UK]: Emission output requires improvement
  Emission output requires improvement
  update software in the engine control unit and replace the nox sensor if required.

  Show Content

• Recall R/2018/268 [UK]: Doors on left vehicle side (passenger side) remain permanently locked after the vehicle has been locked/unlocked with the remote control key
  Possible inability to open the left hand door externally or internally.
  replace the affected door locks on the left side of the vehicle.

  Show Content

• Recall R/2020/236 [UK]: The emergency call system (ecall) does not meet the specification
  On affected vehicles the software of the communication module for the emergency call system does not meet the specification
  update the software of the communication module for the emergency call system

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Desiccated air bag inflator rupture investigation # EA21002

  From 2000 through 2017, takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("psan") propellant -- propellant 2004 and propellant 2004l. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 blomquist report at www.Nhtsa.Gov/sites/nhtsa.Gov/files/documents/expert_report-hrblomquist.Pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in us vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004l that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated psan inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All takata inflators produced with propellant 2004l contain desiccant, and none of these desiccated inflators using propellant 2004l are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated psan inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- takata (now known as tk global), the independent testing coalition, and exponent -- have been studying the long-term behavior of takata desiccated psan inflators using propellant 2004l (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004l is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004l.The office of defects investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated psan frontal inflators manufactured by takata. This investigation will require extensive information on takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated psan inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.Gov/recalls?Nhtsaid=ea21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede ea15-001, which remains open.
  

  Show Content