PIT5074F
Service Bulletin Details
Public Details for: PIT5074F
Gm: j-35616-64b terminal test probe and replacement terminal. Also included models verano, regal, lacrosse, cts, srx, volt, sonic, malibu, impala, equinox, cruze, avalanche, tahoe suburban, silverado, sierra, yukon, and terrain for model
- 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 -
Models from 2012
Models from 2011
Models from 2010
Models from 2009
Models from 2008
Models from 2007
Models from 2006
Models from 2005
| 2005 CADILLAC SRX |
| 2005 CADILLAC STS |
| 2005 CHEVROLET AVEO |
| 2005 CHEVROLET COBALT |
| 2005 CHEVROLET MALIBU |
| 2005 PONTIAC G6 |
| 2005 PONTIAC PURSUIT |
Models from 2004
| 2004 CADILLAC SRX |
| 2004 CHEVROLET AVEO |
SB-10044242-905 File in Section: Service Bulletin - Bulletin No.: PIT5074F Date: May, 2012 PRELIMINARY INFORMATION Subject: J-35616-64B Terminal Test Probe And Replacement Terminal Models: 2010 - 2013 Buick LaCrosse 2011 - 2013 Buick Regal 2012 - 2013 Buick Verano 2007 - 2013 Cadillac Escalade Models 2006 - 2013 Cadillac CTS 2006 - 2011 Cadillac DTS 2004 - 2013 Cadillac SRX 2005 - 2011 Cadillac STS 2007 - 2013 Chevrolet Avalanche, Suburban, Silverado, Tahoe 2004 - 2011 Chevrolet Aveo 2005 - 2010 Chevrolet Cobalt All Models 2011 - 2013 Chevrolet Cruze 2010 - 2013 Chevrolet Equinox 2006 - 2011 Chevrolet HHR 2005 - 2013 Chevrolet Malibu 2006 - 2013 Chevrolet Impala 2012 - 2013 Chevrolet Sonic 2011 - 2013 Chevrolet Volt 2007 - 2013 GMC Sierra, Yukon And Denali Models 2010 - 2013 GMC Terrain 2007 - 2010 Pontiac G3 2007 - 2010 Pontiac G5 2005 - 2010 Pontiac G6 2008 - 2009 Pontiac G8 2005 - 2006 Pontiac Pursuit (Canada Only) 2006 - 2010 Pontiac Solstice 2005 - 2010 Pontiac Wave (Canada Only) With Or Without Any Of The Following DTCs: U0073 U0100 U0101 U0102 U0106 U0109 U0121 U0122 U0132 U0137 U0140 U0151 U0155 U0159 U0164 U0168 U0184 U0198 U0199 U0200 U0214 U2100 This PI was superseded to update model and model years. Please discard PIT5074E. The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. When diagnosing an intermittent electrical concern, terminal tension is one of the main culprits, especially when working with very small terminals. More and more modules are using small .64 series terminals and when checking terminal tension it is important to use the correct test probe. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals, see pic below. Note: Always refer to the Connector End View in Service Information for the latest information on determining the correct test probe to use. If the terminal end of the J-35616-64B is bent, damaged, worn or broken it should not be used and a replacement test probe or terminal should be obtained from GM Tools at 1-800-468-6657. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2, shown below (Note: When calling Kent-Moore to order terminal 963716-2, the actual part number is 963716-2PKG since they are only sold as a pack). This terminal may also be used to make jumper wires, example to jumper the High Speed LAN circuits together in order to bypass a module for testing only. Use crimping tool J-38125-641 and jaw "H" for 22ga wire, "J" for 20 ga wire, or "K" for 18 ga. If you cannot locate the Terminals in your terminal kit "Tray 7" your kit is not up to date and Kent tools will need to be contacted so your kit can be updated. See photos below: 2596949 2596954 2698913 2698910 Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.