13-AT-006
Service Bulletin Details
Public Details for: 13-AT-006
Summary to be provided on a future date.
Models from 2012
2012 HYUNDAI ACCENT |
2012 HYUNDAI AZERA |
Models from 2010
2010 HYUNDAI SANTA FE |
2010 HYUNDAI TUCSON |
GROUP ($?/) HYUnDRI I nEWTHlnKlnG. nEW POSSIBILITIES. - Technical Service Bulletin NUMBER AUTOMATIC TRANSMISSION DATE MODEL MARCH 2013 SUBJECT: 13-AT-006 Tucson (LM), Santa Fe (CM/AN/NC), Sonata (YF/YF HEV), Elantra (UD/MD/GD/JK), Accent (RB), Azera (TG/HG), Veloster Turbo (FS) AUTOMATIC TRANSAXLE (6-SPEED) ATF FLUID LEVEL CHECK This TSB supersedes TSB 11-AT-004 to include 2013 models Description: The following veh icles are equipped with a 6-speed automatic transmission. The ATF level can be checked by the following procedure : *NOTE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-Ill or other ATF which may result in degradation of shift quality or transaxle durability. Model Model Years Applicable Vehicles: 2010- Tucson (LM) & Santa Fe (CM) 2011- Sonata (YF)/HEV, Elantra (UD/MD) & Azera {TG) 2012- Accent (RB) , Azera (HG) 2013- Veloster Turbo (FS) , Elantra Coupe (JK) , Elantra GT (GD) and Santa Fe (AN/NC) PARTS INFORMATION: Hyundai SPH-IV SP-IV Automatic Transmission Fluid 00232-19045 WARRANTY INFORMATION: Normal warranty applies Circulate To : Service Manager, Warranty Manager, Service Advisors , Technicians , Fleet Repair SUBJECT: ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713 SERVICE PROCEDURE: 1. If the ATF has been completely drained , add approximately 5 quarts of SPH-IV ATF . 2. Attach a GOS and select: • Vehicle and AfT menu . • Cu rrent Data • Oil temperature sensor. Value Unit fli 0 §I General Information l"1 OTC Information Si Soeciflcation ~ OTC Inspection ~ Wiring lnsoection ~ Component lnspectio 13 Verification of Reoair 13 Component Location §JETM O Input Speed(PG..A) Output Speed(PG.B) 0 Shift lever Swt1ch RPt.1 RPt.1 p D Current Gear D 0 D 0 D 0 PIH 0 0 0.0 0 0 0 0 OFF OFF 0 0 OFF 0 0 2.0 OFF OFF OFF 3.9 0.0 OFF Next Ge a r Position Engine RPM Gear Ratio Shift Control Solenoid Valve A(UOIB) Shift Control Solenold Valve 6(2-0/B) Shift Control Solenoid Valve C(35R/C) D Shift Control Solenoid Valve 0(00/Q 0 Shift Control Solenoid Valve E(SS.A) D Shlf1 Control Solenoid Valve F(SS-8) 0 Pressure Control Solenoid Valve(VFS) '"A"' 0 0 D 0 Torque Converter Outch So lenoid Valve Torque Conve rter Outch Control State Torque Converter Outch Slip Vehicle Speed D Engine Torque 0 Sports Mode Select 0 Sports Mode Up Switd1 D Sports Mode Down Switch D Throttle Position Senso r Angle 0 Acce lerator Peda l Position Senso r Brake Switch n Cue Analysis OTC DVOM RPM mA mA mA mA mA mA RPt.1 fAPH ll ll ll Oscinoscope SimUlatiOn Test 3. Drive the vehicle until the fluid temperature is at the low end of the range of 122-140°F (50-60°C). 4. Step on the brake and then shift into "R", "N" and "D" and back, pausing 2-3 seconds in each range . Repeat two times . Move the shift lever to P, leave the engine running (Sonata Hybrid in "EV Ready" mode) and lift the vehicle on a hoist. 5. Remove the splash shield under the transmission. TSB #: 13-AT-006 Page 2 of 3 SUBJECT: 6. ATM OIL TEMPERATURE SENSOR OTC P0711 , P0712 & P0713 Remove the oil level plug. The oil level is correct if ATF flows out in a thin steady stream . If no oil flow occurs , go to Step 7. ATF Temperature= 122-140F (50-GOC) Shift lever in " P" and engine running HEV in " EV Ready" mode 7. If no oil flow occurs, add SPH-IV ATF through the fill plug opening or use a suction gun to add ATF through the level checking plug. Reinstall the plug. Filling and checking of flu id level is done through va lve body s ide cover Start the engine and shift to Park. When the ATF is 122°F-140°F (50-60 °C) , remove the level checking plug . The level is correct when oil flows out of the level checking plug in a thin steady stream . *NOTE Collect and dispose of any excess fluid in accordance with local regulation. 8. I Fill Plug shown I Level Checking Plug ATF TEMPERATURE = 122 - 140F (50- 60C) SHIFT LEVER IN " P" AND ENGINE RUNNING Reinstall the overflow plug and torque to specification . Steel pan : Torque: 25-32 lb-ft (3.5-4 .5 kgf.m) Plastic pan : Turn plug past detent. TSB # : 13-AT -006 Page 3 of 3