13-FL-011

(8) HVUnDRI I
Technical Service Bulletin
SUBJECT
NUMBER
GROUP
nEWTHlnKlnG.
nEW POSSIBILITIES.
13-FL-011
FUEL SYSTEM
MODEL
DATE
OCTOBER 2013
TUCSON (LM)
ECM UPDATE - MIL ON OTC P0300/P0301/P0302/P0303/P0304
Gi>~ ® HYUn~R,
ECU Update
*NOTE:
This TSB contains different procedures than past ECU Updates, follow all the steps provided
by this TSB.
Description:
This bulletin provides information for an ECM diagnostic code logic update on some 20122013MY Tucson 2.4L vehicles that may experience the following OTC:
-
P0300 : Random/Multiple Cylinder Misfire Detected.
P0301 : Cylinder 1 - Misfire Detected.
P0302 : Cylinder 2 - Misfire Detected.
P0303 : Cylinder 3 - Misfire Detected.
P0304: Cylinder 4 - Misfire Detected.
Note: This bulletin is associated with cold engine start rough idle only.
Applicable Vehicles:
•
12-13 MY TUCSON (LM) 2.4L MPI.
GDS Information:
EVENT#
317 (or later compatible event)*
DESCRIPTION
"LM 2.4 MPI P030X OTC LOGIC IMPROVEMENT"
(*the latest event that shows up in the Engine Auto Mode event list for the particular vehicle/engine)
Warranty Information:
Model
Op Code
Operation
Op Time
Causal P/N
Nature
Cause
TUCSON (LM)
39110F9K
ECM UPGRADE
0.3
(See NOTE)
N69
C40
NOTE: Use the applicable ECM P/N listed in the ROM ID Information Table from the following page.
*NOTE:
In event of AUTO MODE update failure:
• You must attempt MANUAL MODE. Use the ECM P/N from the vehicle's ECM label if it is
not clear from the ROM ID Table as to the correct ECM P/N to use for your vehicle .
• Replacing an ECM without carefully documenting that a MANUAL MODE update attempt was
made may result in warranty claim charge back.
Circulate To: Service Manager, Warranty Manager, Service Advisors , Technicians , Fleet Repair
SUBJECT:
ECM UPDATE - MIL ON OTC P0300/P0301/P0302/P0303/P0304
ROM ID INFORMATION TABLE:
q.J,.~
Model
.ct-~~
~
~
MY
.
~
'd
~
Emission
ECM P/N
T/M
IMMO
(Start
type)
AT
ULEV
39116-2G802
MT
New
No
(key)
LCC4MP4A
LCC4MQOA
LCC4MQOB
LCC4MR1A
LCC4MR18
No
(key)
LCS4MP4A
LCS4MQOA
LCS4MQOB
LCS4MR1A
LCS4MR1B
No
(key)
LDC4MSOA
LDC4MTOA
LDC4MTOB
LDC4MT1B
LDC4RSOA
LDC4RTOA
LDC4RTOB
LDC4RT1B
LDS4MSOA
LDS4MTOA
LDS4MTOB
LDS4MT1B
LDS4RSOA
LDS4RTOA
LDS4RTOB
LDS4RT1B
12MY
SU LEV
LM
2.4L
MPI
ULEV
39106-2G822
AT
39106-2G803
AT
39116-2G803
MT
39106-2G813
AT
39106-2G823
AT
39106-2G883
AT
~~
Previous
39106-2G802
ROMID
Yes
(SSB)
13MY
No
(key)
SU LEV
Yes
(SSB)
General Precautions:
• Connect the USB cable between the GOS and
the VCI.
• Connect the 16-pin DLC connector from the VCI
into the DLC located under the driver's side dash .
*NOTE
Make sure the battery icon at the bottom right of the GOS laptop shows at least 50% ; if not, charge
the GOS or attach a battery charger.
•
Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories (including
heater/air conditioner/fan , audio, heated seats , rear defroster, etc) to ensure the battery will not
be discharged during the update.
•
Perform the update with the ignition key in the ON position.
•
Do not disconnect any cables connected to the vehicle or the GOS during the update.
•
Do not start the engine or turn the ignition switch OFF during the update.
TSB # : 13-FL-011
Page 2 of 4
ECM UPDATE - MIL ON OTC P0300/P0301/P0302/P0303
SERVICE PROCEDURE:
GOS AUTO MODE ECM UPDATE PROCEDURE
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN.
2. Select Engine as the system and then select OK.
3. Select Auto Mode and then select Next.
4. From the System tab , select Engine and then select OK. The GOS will read the ROM ID .
Confirm the ROM is applicable as shown on Page 2, "ROM ID Information".
Special Instruction for 2013MY vehicle only:
•
If a 2013MY vehicle produces the message 'This ECU upgrade event does not
apply to this ECU" then you will need to go to GOS MANUAL MODE ECM UPDATE
PROCEDURE to perform this ECM Update.
5. Select update Event 317: "LM 2.4 MPI P030X OTC LOGIC IMPROVEMENT". Select Upgrade.
6.
If the screen indicates "Voltage is OK" (voltage> 12volts), select OK. If not, select CANCEL
and charge the vehicle battery by running the engine for 10 minutes .
7. Updating will occur until 100% is reached on the bar graph. At the prompt, turn the ignition key
OFF for 10 seconds, then turn it ON and select OK.
8. The GOS
~ill
confirm that ECM reprogramming is successfully finished . Select OK.
9. If the ECM update was not successful , go to GOS MANUAL MODE ECM UPDATE
PROCEDURE.
10. Check for OTC in all systems and Erase All OTC that stored due to loss of CAN communication
during the ECM Update.
11. Perform ETC initialization as per the following:
•
•
Turn ON ignition for 5 seconds with engine not running .
Turn OFF ignition for 10 seconds.
NOTE:
Failure to perform ETC initialization may result in OTC P0368 setting.
12. Start the engine to confirm proper operation .
TSB #: 13-FL-011
Page 3 of 4
SUBJECT:
ECM UPDATE - MIL ON OTC P0300/P0301/P0302/P0303/P0304
GOS MANUAL MODE ECM UPDATE PROCEDURE
*
•
•
•
IMPORTANT NOTE
GOS Manual Mode is intended for recovery of an ECM Update should it
begin but then later fail in process in the Auto Mode, or if a 2013MY vehicle
had error message "This ECU upgrade event does not apply to this ECU".
If the Auto Mode Update had failed then the ECM connectors must be
disconnected for 15 minutes to reset its contents before performing this
Manual Mode Update.
It is critical to identify the correct ECM Part Number and PASSWORD
selection or the ECM may be permanently damaged . If you are not sure it is
recommended to remove ECM and read part number from its label.
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN .
2. Select Engine as the system and then select OK.
3. Select Manual Mode and then select Next.
4. From the System tab , select Engine and then select OK.
5. Select update event as per the GOS Event List of page-1, then select Upgrade.
6. Be certain to carefully make the appropriate vehicle ECM MENU selection and PASSWORD
selection from the table below based on the following vehicle characteristics:
•
•
•
Model Year of Vehicle:
o 12MY [C] in the 101h digit of the VIN
o 13MY [D] in the 101h digit of the VIN
Emissions Certification from the underhood label :
o SULEV (PZEV)
o ULEV
Immobilizer type:
o IMMO (Start/Stop Button vehicle)
o NON IMMO (Key Start vehicle)
and then select OK.
12MY LM
12MY LM
13MY LM
13MY LM
13MY LM
13MY LM
2.4
2.4
2.4
2.4
2.4
2.4
MENU
ULEV NON IMMO : 39106/39116-2G802
SU LEV NON IMMO : 39106-2G822
ULEV NON IMMO : 39106/39116-2G803
ULEV IMMO : 39106/39116-2G813
SULEV NON IMMO : 39106-2G823
SU LEV IMMO : 39106-2G883
PASSWORD
2802
2822
2803
2813
2823
2883
7. The remaining steps are same as Steps 6-12 of the Auto Procedure.
TSB # : 13-FL-011
Page 4 of 4