08-059-12

NUMBER:
GROUP:
DATE:
08-059-12
Electrical
October 23, 2012
This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of Chrysler Group LLC.
THIS BULLETIN SUPERSEDES SERVICE BULLETIN 08-045-11, DATED AUGUST 04.
2011 WHICH SHOULD BE REMOVED FROM YOUR FILES. THIS IS A COMPLETE
REVISION AND NO ASTERISKS HAVE BEEN USED TO HIGHLIGHT REVISIONS.
HELP USING THE wiTECH DIAGNOSTIC APPLICATION FOR FLASHING AN ECU IS
AVAILABLE BY SELECTING "HELP" THEN "HELP CONTENTS" AT THE TOP OF
THE wiTECH DIAGNOSTIC APPLICATION WINDOW.
THE wiTECH SOFTWARE LEVEL MUST BE AT RELEASE 13.01 OR HIGHER TO
PERFORM THIS PROCEDURE.
SUBJECT:
Flash: Power Sliding Door Will Not Power Close And Makes A Clicking Noise
OVERVIEW:
This bulletin involves re-flashing the Power Sliding Door Module (PSDM) with updated
software.
MODELS:
2011
(RT)
Town and Country/ Carvan
2012
(RT)
Town and Country/ Carvan
2013
(RT)
Town and Country/ Carvan
NOTE: This bulletin applies to vehicles built prior to October 13, 2012 (MOH 1013XX)
equipped with Right and left Power Sliding Doors (sales code JRA/JRB).
SYMPTOM/CONDITION:
Customers may experience that the power sliding door will not power close. The sliding
door will be stuck in the open position and the motor will make a clicking noise. There are
no stored Diagnostic Trouble codes (DTC's) in the power sliding door module for this
issue. This will happen when the PSDM loses the position counts. The sliding door will
close manually using the inside or outside door handle.
Flashing the PSDM will correct this condition.
DIAGNOSIS:
-2-
08-059-12
1.
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in
TechCONNECT, verify no DTC's are set. If DTCs are present record them on the
repair order and repair as necessary before proceeding further with this bulletin .
2. Using a Scan Tool (wiTECH) check the part number of the PSDM.
3. Is the PSDM part number 68079909M?
a. Yes>>> Proceed to repair procedure , Step #1 .
b. NO>>> This bulletin doesn't pertain and normal diagnostic should be performed.
If the customer describes the symptom , perform the Repair Procedure.
REPAIR PROCEDURE:
NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2
volts. Do not allow the charging voltage to climb above 13.5 volts during the
flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
1.
Flash reprogram the PSDM. Help using the wiTECH Diagnostic Application for flashing
the PSDM is made available through the wiTECH Diagnostic Application. For
instructions select the "HELP" tab on upper portion of the wiTECH window, then
"HELP CONTENTS." This will open the Welcome to wiTECH Help screen where help
topics can be selected .
2. Has the PSDM part number update to 68079909AB?
a. Yes>>> Proceed to Step #3 .
b. NO>>> The module needs to be reprogrammed again. Proceed to the repair
procedure, Step #1 .
NOTE: If the PSDM has been flashed a number of times then this bulletin doesn't
pertain and further diagnostics need to be performed.
3. Has both PSDM's been updated with the latest software?
a. Yes>>> Proceed to Step #4.
b. No>>> Perform flash on the other PSDM , proceed to the repair procedure, Step #1 .
4. Clear any DTC's that may have been set in other modules due to reprogramming. The
wiTECH application will automatically present all DTCs after the flash and allow the
tech to clear them.
5. Perform the power sliding door relearn procedure in TechCONNECT, 08 Electrical/8N - Power Systems/Power Sliding Door/Standard Procedure, POWER
SLIDING DOOR LEARN CYCLE.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation
No:
Description
Amount
18-19-31 -92
Module, PSDM's - Inspect (Skill Level= C;
Training Level = 2)
0.2 Hrs.
18-19-31-93
Module, PSDM's - Inspect & Reprogram (Skill
Level = C; Training Level = 2)
0.2 Hrs.
•
-3FAILURE CODE:
IFM
IFlash Module
08-059-12