A16-094
Service Bulletin Details
Public Details for: A16-094
Service bulletin - an inaccurate calibration setting in the software is causing engine torque fluctuations while driving at highway speeds. This will cause the mil to come on and the vehicle may enter fail-safe mode, which will limit the ve
Models from 2015
2015 HONDA ACCORD HYBRID |
Service Bulletin 16-094 November 5, 2016 05080 Version 1 MIL Comes On with DTC P14A0 and/or P1DFD AFFECTED VEHICLES Year Model 2014 Accord Plug-In 2014–15 Accord Hybrid Trim ALL ALL VIN Range ALL ALL SYMPTOM • The MIL comes on, and DTC P14A0 (Engine Abnormal Vibration) and/or P1DFD (Power System Indicator Lighting Request From PCM) are set. • Accord Plug-In only - DTC P0300 (Random Misfire Detected), P0301 (No. 1 Cylinder Misfire Detected), P0302 (No. 2 Cylinder Misfire Detected), P0303 (No. 3 Cylinder Misfire Detected), and/or P0304 (No. 4 Cylinder Misfire Detected) may be set. • Engine vibrates similar to conditions for misfire and/or loss of power. POSSIBLE CAUSES An inaccurate calibration setting in the software is causing engine torque fluctuations while driving at highway speeds. This will cause the MIL to come on and the vehicle may enter fail-safe mode, which will limit the vehicles power output. CORRECTIVE ACTION Update the PGM-FI software. WARRANTY CLAIM INFORMATION The normal warranty applies. Operation Number 1255D8 A Skill Level: Description Flat Rate Time Update the PGM-FI software. 0.2 hr CKP pattern clear/learn 0.1 hr Defect Code Symptom Code Template ID Failed Part Number 03214 03203 16-094A 37805-5K1-A57 Repair Technician CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2016 American Honda Motor Co., Inc. – All Rights Reserved Page 1 of 4 SOFTWARE INFORMATION NOTE: Unnecessary or incorrect repairs resulting from a failure to update the i-HDS are not covered under warranty. i-HDS Software Version: 1.001.011 or later J2534 Software Information: PC Application Version 1.0.1.15 or later Database update 26-OCT-2016 or later Before beginning the repair, make sure that both the i-HDS and the J2534 software are updated as listed above. Do only the update listed in this service bulletin. You cannot apply the updates with the MVCI as a standalone tool. To update the vehicle you must use the MVCI or the DST-i interface in conjunction with the J2534 Rewrite PC application on the i-HDS. For more information about updating the i-HDS, the MVCI, and the vehicle systems, refer to Service Bulletin 01-023, Updating Control Units/Modules. Year/Model Software System Program ID (or later) Program P/N (or later) 2014 and 2015 Accord Hybrid PGM-FI K1A580 37805-5K1-A58 2014 and 2015 Accord Hybrid w/ ACC PGM-FI K1A680 37805-5K1-A68 2014 Accord Plug-In PGM-FI K0A140 37805-5K0-A14 REPAIR PROCEDURE NOTE: • You can’t update the vehicle using the MVCI as a standalone tool. • Do not use the MongoosePro VCI tool. • Make sure the 12 volt battery is fully charged before starting an update. • Connect a fully charged jumper battery to the vehicle and leave it connected during the entire procedure to maintain steady voltage. • Never turn the ignition to OFF or ACCESSORY during the update. If there is a problem with the update, leave the ignition turned to ON. • To prevent powertrain control module damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power windows, door locks, etc.) during the update. • If you see the following Error Display, check that you are using the correct tool (MVCI or DST-i) with the i-HDS. Page 2 of 4 To change this, click on either of the SETTING selection buttons at the bottom of the J2534 initial screens as shown. 1. Make sure the parking brake is applied and the headlights are off. 2. Update the PGM-FI software by selecting the i-HDS Diagnostic System icon. Refer to Service Bulletin 01-023, Updating Control Units/ Modules. NOTE: Do not use the Rewrite icon on your desktop. 3. Select J2534 Rewrite. 4. Confirm the software is the same or later as listed in SOFTWARE INFORMATION. Page 3 of 4 5. Select Start, then follow the screen prompts. NOTE: • Don’t enter a bulletin number. • If you receive a message that the vehicle has been already updated or that no update is available, check the engine data list. The header should indicate one of the following numbers (or later). 37805-5K1-A58 • 37805-5K1-A68 37805-5K0-A14 If the program part numbers do not match those listed above, the i-HDS software needs to be reinstalled. Contact the Special Tools Hotline at 800-346-6327 for assistance. 6. Do the CKP pattern clear/learn procedure. END Page 4 of 4