A191562 2025303-

Technical Service Bulletin
19 Identifying and mixing factory fill engine coolants
19 15 62 2025303/6 September 8, 2015. Supersedes Technical Service Bulletin Group 19 number 15-61 dated
July 7, 2015 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
All
1994 - 2018
All
Not Applicable
Condition
REVISION HISTORY
Revision
Date
Purpose
6
-
Revised Service (Added information about reusing coolant)
5
7/7/2015
Revised header data (Added model years)
4
6/20/2014
Revised header data (Added model year)
Discontinuation and mixing of Audi-approved engine coolants.
Technical Background
• G11, G12, and G12+ coolants have been replaced by an improved version.
• G12++ coolant (for service available) has been introduced in MY 2005 for all engines.
• G13 has been introduced in MY 2008 as factory filling and service.
Production Solution
No production change required.
© 2015 Audi of America, Inc.
Page 1 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Service
Identifying and mixing factory fill engine coolants
1. Based on its color, identify which coolant
the vehicle was filled with from the factory
(Figure 1).
Tip: Figure 1 is shown for color
identification only; coolant packaging may
vary.
Figure 1. The color of each type of engine coolant. G11 (greenblue), G12 (red), G12+, G12++ and G13 (purple).
2. Using the chart at right, determine if the
vehicle has the correct coolant (Figure 2). If
a vehicle is found to have the incorrect
coolant, drain and fill the coolant system
using the repair manual procedures in Elsa.
Figure 2. The table identifies which Service coolants (left) can be
added to the Factory Filled coolant (top).
Note:
Coolants can be mixed, as described in the chart, but it is always best practice to change the coolant due to
reduced corrosion protection when coolants are mixed (exception: G12++ and G13 are fully compatible).
Only use distilled water for mixing coolant.
Drained coolant must not be reused.
© 2015 Audi of America, Inc.
Page 2 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Note:
When the coolant is changed due to a cooling system issue, the cooling system should be drained using the repair
manual procedures in Elsa and refilled with water and the engine run for 15 minutes with the heater on to remove
any residual coolant. Then drain and fill the system to the freeze protection ratio listed in Elsa.
Tip: Cooling system drain and fill due to coolant mixing, or incorrect coolant, is not covered by warranty.
Warranty
This TSB is informational only and not applicable to any Audi warranty.
Required Parts and Tools
No special tools required.
Additional Information
All part and service references provided in this Technical Bulletin (2025303) are subject to change and/or removal.
Always check with your Parts Department and Repair Manuals for the latest information.
© 2015 Audi of America, Inc.
Page 3 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.