TSB 18-2270
Service Bulletin Details
Public Details for: TSB 18-2270
- 2018 -
Models from 2018
2018 FORD F-150 |
TECHNICAL SERVICE BULLETIN 18-2270 30 August 2.7L EcoBoost - Illuminated Malfunction Indicator Lamp (MIL) - DTC P0300, 2018 P0316, P0301-P0306, P2196, P2198, P0171, And/Or P0174 - Built On Or Before 12-Jul-2018 Model: Ford 2018 F-150 Issue: Some 2018 F-150 vehicles equipped with a 2.7L EcoBoost built on or before 12-Jul-2018 with greater than 500 miles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0300, P0316, P0301-P0306, P2196, P2198, P0171, and/or P0174 stored in the powertrain control module (PCM). Action: Follow the Service Procedure steps to correct the condition. Parts Part Number Description Quantity JT4Z-9F593-B High Pressure Direct Fuel Injector 6 JT4Z-9C995-A Injector Clip 6 JT4Z-9J323-A High Pressure Fuel Tube 1 FT4Z-9J323-B High Pressure Fuel Tube 1 FOPZ-9229-A Port Fuel Injector O-Ring Kit 1 JT4Z-9E464-B Exhaust Gas Recirculation (EGR) Gasket 1 JT4Z-9H486-A Intake Gasket Kit 1 Warranty Status: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage Warranty/ESP coverage limits/policies/prior approvals are not altered by a TSB. Warranty/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool. Labor Times Operation Time No. Description 2018 F-150 2.7L: Retrieve DTCs, Monitor PIDs And Replace The Direct Injection Fuel Injectors (Do Not Use With Any Other Labor Operations) Repair/Claim Coding Causal Part: 9F593 Condition Code: 42 Tool List Drive Tool Name 1/4" Power Tool 1/4" Torque Wrench 1/4" Ratchet 1/4" 2" Extension 1/4" 6" Extension 1/4" 10" Extension 182270A 4.4 Hrs. Drive Tool Name 1/4" 7 mm Socket 1/4" 10 mm Socket 1/4" 13 mm Socket 1/4" 8 mm Deep Socket 1/4" 10 mm Deep Socket Small Trim Tool Large Trim Tool 10 mm Wrench 18 mm Wrench 18 mm Crows Foot (Flare) 3/8" Fuel Line Disconnect Mirror Pliers Shop Light Tool Number Essential Special Service Tool 303-1567 Teflon Seal Sizer 307-005 Slide Hammer 310-205 Fuel Injector Brush 310-206 Fuel Injector Remover 310-207 Fuel Injector Seal Assembly Installer Service Procedure 1. Check the vehicle build date. Was the vehicle built on before 12-Jul-2018 and have more than 500 miles on the odometer? (1). Yes - proceed to Step 2. (2). No - this article does not apply. Refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for diagnostics. 2. Using the appropriate Ford diagnostic scan tool or equivalent, retrieve DTCs. Are DTCs P0300, P0316, P0301P0306, P2196, P2198, P0171, and/or P0174 stored in the PCM? (1). Yes - proceed to Step 3. (2). No - this article does not apply. Refer to the PC/ED Manual for diagnostics. 3. Monitor fuel rail pressure using the appropriate Ford diagnostic scan tool. Start the engine and allow it to idle for 30 seconds. Shut off the engine and monitor fuel rail pressure. Does the fuel rail pressure drop below 6.9 kPa (10 psi) within 30 seconds after engine shut down? (1). Yes - replace the direct injection fuel injectors. Refer to the Workshop Manual (WSM), Section 303-04A. (2). No - this article does not apply. Refer to the PC/ED Manual for diagnostics. © 2018 Ford Motor Company All rights reserved. NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supersede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.