NTB16-037e

Classification:
Reference:
EC16-013e
Date
NTB16-037e
February 28, 2019
2016 TITAN XD; MIL ON WITH ENGINE DTCs STORED
AND/OR IDLE FLUCTUATION
This bulletin has been amended. See Amendment History on the last page.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
APPLIED ENGINE:
2016 Titan XD (A61)
Cummins 5.0L V8 Diesel
IF YOU CONFIRM
The MIL is ON with one or more of the following DTCs stored:


















P020A - F: Cylinder 1 – 6 Injection Timing
P021A - B: Cylinder 7 – 8 Injection Timing
P060C: Internal Control Module Main Processor Performance
P061B: Internal Control Module Torque Calculation Performance
P0605: ECM
P0299: Boost Pressure
P2263: Turbocharger Boost System Performance
P0401: Flow in the Exhaust Gas Recirculation (Insufficient)
P0402: Flow in the Exhaust Gas Recirculation (Excessive)
P2483: Exhaust Gas Temperature Sensor Circuit Intermittent 1/5
P244D: Exhaust Temperature Too High For PF Regeneration
U0415: VDC CAN CIR2
P2BAD: NOx Concentration Exceeded
P1C55: NOx Sensor 1/1 Intermittent
P1C56: NOx Sensor 1/2 Intermittent
P2201: NOx Sensor 1
P229F: NOx Sensor 2
P064C: Glow Output Stage
and/or
At times, when coming to a stop, the idle fluctuates with RPM dropping below 500 RPM.
See page 2 for ACTION section.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/16
ACTION
1. Save Computer Data with CONSULT-III plus (C-III plus).
2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle
you are working on.
3. If this bulletin applies, continue with reprogramming procedure.
4. Write Saved Data with CONSULT-III plus.
IMPORTANT: The purpose of ACTION above is to give you a quick idea of the work
you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as
it contains information that is essential to successfully completing this repair.
2/16
NTB16-037e
SERVICE PROCEDURE
Save Computer Data
1. Connect the CONSULT PC to the vehicle.
2. Open / start C-III plus.
3. Turn the ignition ON, with engine OFF (engine not running).
4. Wait for the plus VI to be recognized.

The Serial No. will display when the plus VI is recognized.
5. Select Diagnosis (One System).
Step
5
Step 4:
plus VI is
recognized
Figure A
3/16
NTB16-037e
6. Navigate C-III plus to Engine > Work Support (see Figure B).
7. Select SAVE COMPUTER DATA.
8. Select Start.
Step
6
Step
7
Step
8
Figure B
NOTE:

After selecting Start, a screen message may appear that says:
Latest diagnostic tool update must be used before saving the data,
otherwise there is a risk that the data entry will not work.

If the above message appears, select Continue.
4/16
NTB16-037e
9. Make sure the ignition is ON and the engine is OFF (engine not running).
10. Select Confirm.
Step
10
Figure C
11. Select End.
Step
11
Figure D
5/16
NTB16-037e
ECM Reprogramming
IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

All CONSULT-III plus (C-III plus) software updates (if any) have been installed.

The CONSULT PC is connected to the Internet (Wi-Fi or cable).
NOTE:

Most instructions for reprogramming with CONSULT-III plus (C-III plus) are
displayed on the CONSULT PC screen.

If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.

For the Titan XD Diesel, the GR8 set to ECM power supply mode can be attached to
either 12 volt battery.
CAUTION:

Connect the GR8 to the 12V battery and set to ECM power supply mode.
If the vehicle battery voltage drops below 12.0V or above 15.5V during
reprogramming, the ECM may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the ECM may be damaged.

Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within
range of the CONSULT PC and the plus VI. If Bluetooth® signal waves are
within range of the CONSULT PC during reprogramming, reprogramming may
be interrupted and the ECM may be damaged.
6/16
NTB16-037e
1. Return to the C-III- plus Home screen (see Figure 1).
2 Confirm the ignition is ON, with engine OFF.
3. Confirm the plus VI is recognized.

The Serial No. will display when the plus VI is recognized.
4. Select Re/programming, Configuration.
Step 3:
plus VI is
recognized
Step
4
Figure 1
5. Follow the on-screen instructions and navigate C-III plus to the screen shown in
Figure 2 on the next page.
6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).
xxxxxxxxxxxxxxxx
Step 6A:
Current ECM P/N
xxxxx
xxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
Figure 2
7/16
NTB16-037e
B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number
column in Table A below.

If there is a match for EZ41C, EZ41D, or EZ41E this bulletin applies. Continue
with the reprogramming procedure.

If there is a match for EZ42A:
 If vehicle has the confirmed symptom of “idle fluctuates when coming to a
stop”, this bulletin applies. Continue with the reprogramming procedure.
 If only DTC P060C and P2263 were stored and no idle fluctuation, this
bulletin does not apply. Close C-III plus and refer to ASIST for further
diagnostic information.
 If a DTC listed on page 1 other than P060C and P2263 was stored, this
bulletin applies. Continue with the reprogramming procedure.

If there is a match for EZ42B or EZ42C:
 If only DTC P060C, P2263, P244D, P061B, P2483, P2BAD, P1C55, P1C56
and/or P229F was stored, this bulletin does not apply. Close C-III plus and
refer to ASIST for further diagnostic information.
 If a DTC listed on page 1 other than those listed above was stored, this
bulletin applies. Continue with the reprogramming procedure.
 If vehicle has confirmed symptom of “idle fluctuates when coming to a stop”,
but no DTCs are stored, this bulletin does not apply. Close C-III plus and refer
to ASIST for further diagnostic information.

If there is no match, this bulletin does not apply. Close C-III plus and refer to
ASIST for further diagnostic information.
Table A
Model
Current ECM Part Number: 23710-
2016 Titan XD
Cummins Diesel
EZ41C, EZ41D, EZ41E
EZ42A, EZ42B, EZ42C
8/16
NTB16-037e
7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.
NOTE:

In some cases, more than one new P/N for reprogramming is available.
 If more than one new P/N is available, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.

If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for
further diagnosis.
xxxxx-xxxxx
xxxxx-xxxxx
xxxxx-xxxxx
xxxxx xxxxx
xxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxx
Figure 3
9/16
NTB16-037e
8. When the screen in Figure 4 displays, reprogramming is complete.
NOTE: If the screen in Figure 4 does not display (indicating that reprogramming did
not complete), refer to ECM recovery on the next page.
9. Disconnect the GR8 (battery charger) from the vehicle.
10. Select Next.
Step
10
Figure 4
NOTE:

In the next step (page 12) you will perform DTC erase.

This operation is required before C-III plus will provide the final reprogramming
confirmation report.
10/16
NTB16-037e
ECM Recovery
Do not disconnect the plus VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 5:

Check battery voltage
(12.0 - 15.5 V).

Ignition is ON, engine OFF.

External Bluetooth® devices
are OFF.

All electrical loads are OFF.

Select retry and follow the
on screen instructions.

“Retry” may not go through on
first attempt and can be
selected more than once.
Figure 5
If reprogramming does not complete and the “X” icon displays as shown in
Figure 6:

Check battery voltage
(12.0 - 15.5 V).

CONSULT A/C adapter is
plugged in.

Ignition is ON, engine OFF.

Transmission is in Park.

All C-III plus / VI cables are
securely connected.

All C-III plus updates are
installed.

Select Home, and restart
the reprogram procedure
from the beginning.
Figure 6
11/16
NTB16-037e
11. Follow the on-screen instructions to Erase DTCs.
12. When the entire reprogramming process is complete, the screen in Figure 7 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty
documentation.
15. Select Confirm.
xxxxxx
Step
13
xxxxxx
xxxxxxx
xxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxx
Step
14
Step
15
Figure 7
Continue to the next page.
12/16
NTB16-037e
Write Saved Data
1. Return to the C-III- plus Home screen (see Figure 1A).
2 Confirm the ignition is ON, with engine OFF.
3. Confirm the plus VI is recognized.

The Serial No. will display when the plus VI is recognized.
4. Select Diagnosis (One System).
Step
4
Step 3:
plus VI is
recognized
Figure 1A
13/16
NTB16-037e
5. Navigate C-III plus to Engine > Work Support (see Figure 2A).
6. Select WRITE SAVED DATA.
7. Select Start.
Step
5
Step
6
Step
7
Figure 2A
8. Make sure the ignition is ON and the engine is OFF (engine not running).
9. Select Confirm.
Step
9
Figure 3A
14/16
NTB16-037e
10. Wait for the procedure to complete.
Figure 4A
11. Select End.
Step
11
Figure 5A
15/16
NTB16-037e
12. Close C-III plus.
13. Turn the ignition OFF.
14. Disconnect the plus VI from the vehicle.
15. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.

If the MIL comes ON, go back to ASIST for further diagnostic information.

Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE SYM
DIA
FRT
Reprogram Engine Control Module
(1)
DE97AA
ZE
32
(2) (3)
(1) Refer to the electronic parts catalog and use the ECM assembly part number as the
Primary Failed Part (PFP).
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.
(3) FRT allows adequate time to access DTC codes and reprogram ECM. No other
diagnostic procedures subsequently required. Do NOT claim any Diagnostic Op Codes
with this claim.
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE DESCRIPTION
March 14, 2016
NTB16-037
Original bulletin published
April 7, 2016
NTB16-037a
Procedure has been changed throughout
May 18, 2016
NTB16-037b
Updated the IF YOU CONFIRM section
May 31, 2016
NTB16-037c
Added DTCs to If You Confirm section
October 17, 2016
NTB16-037d
Amended IF YOU CONFIRM section
February 28, 2019
NTB16-037e
Removed DTC P2048
16/16
NTB16-037e