TS-C113

SERVICE BULLETIN
Bulletin Type............: C
Subject: Alignment Specifications of TS30
Bulletin No...............: TS-C113
Bulletin Name..........: Alignment Specifications of TS30
Bulletin Ref No.........: 700002913
Summary : This bulletin defines alignment
specifications of the TS30 vehicle.
NHTSA…………….........:
Release Date...........:
Expiry Date………........:
Bulletin Responsible: Mert SALMAN
Published by&Approved by: Mert SALMAN
Vehicle Model...........: TS 30
Fiat Rate Code...........: TSC113
Flat Rate Time...........:
Welding on the Chassis
• Always disconnect the batteries (starting with the negative lead).
• Disconnect the connectors of electrical and electronic equipment (electronic control units, sensors and
actuators) if they are less than 2 meters away from the chassis part to be welded or the earth terminal of the
welding equipment.
• The earth terminal should never be attached to vehicle components such as engine, axles and springs. Arcing on
these
parts is not permitted, because of the risk of damage to bearings, springs, etc.
• The earth terminal must make good contact and be placed as close as possible to the part to be welded.
• Plastic pipes, rubber parts and parabolic springs should be well protected against welding spatter and
temperatures
higher than 70°.
TS-C113 1 / 4
SERVICE BULLETIN
Service bulletin expiry dates differ according to
service bulletin type.
Definitions
U-Type : Application period of this bulletin is 12
months after the date of issue.U type bulletin is
used for updates that need to be performed upon
customer complaints.
Release Date: As of this date the bulletin is
released and available on E-Doc. Modification
parts can be ordered. The time period between
the release date and the effective date may vary
according to the procurement lead time.
Effective Date: As of this date specified amount
of the total modification parts will be available on
Spare Parts Stock. Modification parts can be
ordered and the application can be performed. (
except non-compliance and safety related
campaigns, i.e. S-Type Bulletin)
• C-Type: Application period of this bulletin is 12
months after the date of issue. C type bulletin is
generally used for supplying technical
instructions or other type of information to
service network.
Part Order Deadline: Last order date for
modification parts. The part orders which will be
placed after this date should be approved by
Regional Coordinator.
Expiry Date: Expiration date for the application.
Bulletin Types
• S- Type: Application period of this bulletin is
18 months after the date of issue. S type bulletin
is used for Recall Campaigns.
• M-Type: Application period of this bulletin is 12
months after the date of issue. M type bulletin is
used for updates that should be implemented
without waiting for customer complaints.
TS-C113 2 / 4
SERVICE BULLETIN
GENERAL PRECAUTIONS
1. Suggested Dress Code:
2. Before Starting the Work:
Always wear protective clothing. Do not wear any damaged or loose-fitting clothing
and remove jewelry before starting the work. In case of long hair use hairnet.
The illustration above shows some of the correct and incorrect clothing that should
be worn during work. Sharp edges should be avoided e.g belts, watches, necklaces etc.
3. Interior materials protection:
Seats, trimming, upholstery stuff and carpeting should be protected with appropriate
coverings.
TS-C113 3 / 4
SERVICE BULLETIN
Application:
Please use following alignment specifications, when you need to have
your vehicle aligned.
ALIGNMENT SPECIFICATIONS
TS30
Left
Nominal
Tolerance
Total
Nominal
Tolerance
Right
Nominal
Tolerance
Front Axle
King Pin Angle
(degrees)
Camber (degrees)
Caster
(degrees)
Individual Toe (in) in
Total Toe
(in) in
8
±
0,5
8
±
0,5
0
2
0,0196
±
±
±
0,5
0
0
0
2
0,0196
±
±
±
0,5
0
0
0,039
±
0
TS-C113 4 / 4