NTB19-064c
Service Bulletin Details
Public Details for: NTB19-064c
Voluntary service campaign 2017-2018 rogue, rogue hybrid, and rogue sport; icc/adas and laser/radar reprogramming this bulletin has been amended. See amendment history on the last page. Please discard previous versions of this bulletin
Classification: Reference: DA19-016c Date: NTB19-064c February 2, 2021 VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. CAMPAIGN ID #: P9327 APPLIED VEHICLES: 2017-2018 Rogue (T32) 2017-2018 Rogue Hybrid (T32) 2017-2018 Rogue Sport (J11) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 20172018 Rogue, Rogue Hybrid, and Rogue Sport vehicles to reprogram the Laser/Radar and/or ICC/ADAS control units. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P9327 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer’s inventory. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. HINT: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/26 REPAIR OVERVIEW Check the Laser/Radar part number (step 20 on page 9). Is the Part Number listed below? No 28438-5FA1A 28438-5FA2A 28438-5FA3A 28438-5HK2A 28438-5HK3A Yes Perform Laser/Radar Reprogramming, beginning on page 3. Check the ICC/ADAS part number (step 45) and compare it to Table A on page 21. No Is the part number in Table A? Yes Perform ICC/ADAS Reprogramming, beginning on page 20. Done HINT: If reprogramming is not performed, refer to the Electronic Service Manual (ESM) for further diagnostic information. 2/26 NTB19-064c SERVICE PROCEDURE Laser/Radar Reprogramming IMPORTANT: Before starting, make sure: ASIST on the CONSULT PC has been synchronized (updated) to the current date. All CONSULT–III plus (C-III plus) software updates (if any) have been installed. The CONSULT PC is connected to the Internet via a cable or Wi-Fi. Later in the procedure you will be required to enter your User Name and Password. The CONSULT PC must be connected to the Internet. If you do not know your User Name and Password, contact your Service Manager. A screen print for warranty documentation can be done from the CONSULT PC during this process while still connected to the vehicle. No Diagnostic Trouble Codes (DTCs) are stored. Use C-III plus to perform Self Diagnosis for all systems. If there are any DTCs: Diagnose, perform repairs, and erase DTCs before continuing. 1. Connect the plus Vehicle Interface (plus VI) to the vehicle. Make sure the plus VI is securely connected. If the plus VI connection is loose during reprogramming, the process will be interrupted and the control unit may be damaged. 2. Connect the AC Adapter to the CONSULT PC. Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the control unit may be damaged. 3/26 NTB19-064c 3. Connect a battery maintainer or smart charger set to reflash mode or a similar setting. If the vehicle’s battery voltage drops below 12.0V or rises above 15.5V during reprogramming, the Laser/Radar control unit may be damaged. 4. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. Make sure to turn OFF all external Bluetooth® devices. If Bluetooth® signal waves are within range of the CONSULT PC and the plus VI during reprogramming, reprogramming may be interrupted and the control unit may be damaged. 5. Turn the ignition ON with the engine OFF. The engine must not start or run during the reprogramming procedure. 6. Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC, blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc. 7. Turn ON the CONSULT PC. 8. Start C-III plus. 4/26 NTB19-064c 9. Wait for the plus VI to be recognized. The serial number will display when the plus VI is recognized. Plus VI is recognized Figure 1 10. Select Re/programming, Configuration. Figure 2 5/26 NTB19-064c 11. Use the arrows (if needed) to view and read all precautions. 12. Check the box confirming the precautions have been read. 13. Select Next. Figure 3 14. Select Automatic Selection(VIN). Example Figure 4 6/26 NTB19-064c 15. Make sure VIN or Chassis # matches the vehicle’s VIN. 16. If the correct VIN is displayed, select Confirm. XXXXXXXXXXX XXXXXX 2018 Figure 5 17. Select Confirm. XXXXXXXXXXX XXXXXX Figure 6 7/26 NTB19-064c 18. Select LASER/RADAR. ENGINE EPS/DAST 3 LASER/RADAR Figure 7 19. Select Reprogramming. Figure 8 8/26 NTB19-064c 20. When you get to the screen shown in Figure 9, confirm that a reprogram is available with the flow chart below. XXXXXXXXXXX XXXXXX XXXXX Current LASER/RADAR P/N XXXXXXXXXX XXXXXXXXXX Figure 9 Find the LASER/RADAR Part Number and write it on the repair order. HINT: This is the vehicle’s current LASER/RADAR Part Number Is the Part Number listed below? No 28438- 5FA1A 28438- 5FA2A 28438- 5FA3A 28438- 5HK2A 28438- 5HK3A Yes Continue with the reprogramming procedure on the next page. Skip to ICC/ADAS Reprogramming on page 20. 9/26 NTB19-064c 21. Select Save. XXXXXXXXXXX XXXXXX XXXXX xxxxxxxxxxxxxxxx XXXXXXXXXXX XXXXXX xxxxxxxxxxxxxxxx XXXXXXXXXX Figure 10 22. Use the arrows (if needed) to view and read all precautions. 23. Check the box confirming the precautions have been read. 24. Select Next. Figure 11 10/26 NTB19-064c 25. Read the Current Part Number and Part Number After Reprogramming. They should be different. 26. Select Next. xxxxx xxxxx These numbers should be different xxxxxxxxxxxxxxxx xxxxx Figure 12 11/26 NTB19-064c HINT: In some cases, more than one new P/N for reprogramming is available. If more than one new P/N is available, the screen in Figure 13 displays. Select and use the reprogramming option that does not have the message “Caution! Use ONLY with NTBXX-XXX”. If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for the Laser/Radar control unit in this vehicle. Proceed to ICC/ADAS Reprogramming on page 20. LASER/RADAR Figure 13 12/26 NTB19-064c 27. Make sure OK is highlighted green (battery voltage must be between 12.0 and 15.5 Volts). 28. Select Next. Battery voltage must stay between 12.0 and 15.5 Volts during reprogramming or reprogramming may be interrupted and the control unit may be damaged. Monitor battery voltage here Figure 14 29. Confirm all Judgment items are OK, then select Start. Monitor battery voltage here EXAMPLE Figure 15 13/26 NTB19-064c 30. Select USA/CANADA Dealers. 31. Select OK. Figure 16 HINT: The above screen may not display if the CONSULT PC has remained ON since the last reprogramming. If the CONSULT PC is not connected to the Internet, the screen in Figure 17 will display. Figure 17 14/26 NTB19-064c HINT: In the next steps, the reprogramming process will begin when Submit is selected. 32. Enter your Username and Password. 33. The CONSULT PC must be connected to the Internet via cable or Wi-Fi. If you do not know your User Name and Password, contact your Service Manager. Select Submit. Figure 18 34. Wait for both progress bars to complete. Figure 19 15/26 NTB19-064c 35. When the screen in Figure 20 displays, the reprogramming is complete. HINT: If the screen in Figure 20 does not display (indicating that reprogramming did not complete), refer to Laser/Radar Recovery on the next page. 36. Disconnect the battery maintainer or smart charger from the vehicle. 37. Select Next. Figure 20 HINT: Additional steps/operations are required before C-III plus will provide the final reprogramming confirmation report. Continue with the reprogramming procedure on page 18. 16/26 NTB19-064c Laser/Radar Recovery Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete. If reprogramming does not complete and the “!?” icon displays as shown in Figure 21: Check battery voltage (12.0 - 15.5 V). Ignition is ON, engine OFF. External Bluetooth® devices are OFF. All electrical loads are OFF. Select retry and follow the on screen instructions. “Retry” may not go through on first attempt and can be selected more than once. Figure 21 If reprogramming does not complete and the “X” icon displays as shown in Figure 22: Check battery voltage (12.0 - 15.5 V). CONSULT A/C adapter is plugged in. Ignition is ON, engine OFF. Transmission is in Park. All C-III plus / VI cables are securely connected. All C-III plus updates are installed. Select Home, and restart the reprogram procedure from the beginning. Figure 22 17/26 NTB19-064c 38. Erase all DTCs as follows: a. Turn the ignition OFF. b. Turn the ignition ON. c. Wait for DTC erase to complete. ON Turn ignition ON > OFF > ON Figure 23 18/26 NTB19-064c 39. Verify the before and after part numbers are different. 40. Print a copy of this screen (Figure 24) and attach it to the repair order for warranty documentation. HINT: If you cannot print the screen: a. Select Screen Capture. b. Name the file. c. Save the file in My Documents. 41. A copy of the screen is now saved in the CONSULT PC. It can be retrieved and printed at a later time. Select Confirm. xxxxx xxxxx XXXXXXXXXXX XXXXXX XXXXXXXXXXX Figure 24 19/26 NTB19-064c ICC/ADAS Reprogramming HINT: LASER/RADAR control unit reprogramming must be performed first (if indicated by the flow chart on page 9) before proceeding. 42. Refer to steps 1-18 starting on page 3 to navigate to Figure 25. 43. Select ICC/ADAS. Figure 25 44. Select Reprogramming. Figure 26 20/26 NTB19-064c 45. When you get to the screen shown in Figure 27, confirm that a reprogram is available as follows. A. Find the ICC/ADAS Part Number and write it on the repair order. HINT: This is the current ICC/ADAS Part Number (P/N). xxxxxxxxxxxxxxxx xxxxx Current ICC/ADAS P/N xxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxx Figure 27 B. Compare the P/N you wrote down to the numbers in the Current ICC/ADAS Part Number column in Table A. If there is a match, continue with the reprogramming procedure. If there is not a match in Table A, proceed to step 55 on page 26. Table A MODEL YEAR 2017 Rogue and Rogue Hybrid 2018 2017 Rogue Sport 2018 CURRENT ICC/ADAS PART NUMBER: 284E76FL1B, 6FL2B, 6FL7B, 6FL8B 7FF7B, 7FF8B 5HR0A, 5HR9A 5HR9B 5HR0C 5HR0E, 5HR1E, 5HR3E, 5HR5E, 5HR6E 6MA0B 6MA1B 6MG0A, 6MG1A, 6MG2A 21/26 NTB19-064c 46. Follow the on-screen instructions to navigate C-III plus and reprogram the ICC/ADAS control unit. Refer to steps 21-34 starting on page 10 for further details. HINT: In some cases, more than one new P/N for reprogramming is available. If more than one new P/N is available, the screen in Figure 28 displays. Select and use the reprogramming option that does not have the message “Caution! Use ONLY with NTBXX-XXX”. If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle. Skip to step 55 on page 26. ICC/ADAS Figure 28 22/26 NTB19-064c 47. When the screen in Figure 29 displays, reprogramming is complete. HINT: If the screen in Figure 29 does not display (indicating that reprogramming did not complete), refer to ICC/ADAS Control Unit Recovery on the next page. 48. Disconnect the battery maintainer or smart charger from the vehicle. 49. Select Next. Figure 29 HINT: Additional steps/operations are required before C-III plus will provide the final reprogramming confirmation report. Continue with the reprogramming procedure on page 25. 23/26 NTB19-064c ICC/ADAS Control Unit Recovery Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete. If reprogramming does not complete and the “!?” icon displays as shown in Figure 30: Check battery voltage (12.0 - 15.5 V). Ignition is ON, engine OFF. External Bluetooth® devices are OFF. All electrical loads are OFF. Select retry and follow the on screen instructions. “Retry” may not go through on first attempt and can be selected more than once. Figure 30 If reprogramming does not complete and the “X” icon displays as shown in Figure 31: Check battery voltage (12.0 - 15.5 V). CONSULT A/C adapter is plugged in. Ignition is ON, engine OFF. Transmission is in Park. All C-III plus / VI cables are securely connected. All C-III plus updates are installed. Select Home, and restart the reprogram procedure from the beginning. Figure 31 24/26 NTB19-064c 50. Follow the on on-screen instructions to erase DTCs. If needed, refer to step 38 on page 18 for further details. 51. When the entire reprogramming process is complete, the screen in Figure 32 will display. 52. Verify the before and after part numbers are different. 53. Print a copy of the screen shown below (Figure 32) and attach it to the repair order for warranty documentation. HINT: If you cannot print the screen: a. Select Screen Capture. b. Name the file. c. Save the file in My Documents. 54. A copy of the screen is now saved in the CONSULT PC. It can be retrieved and printed at a later time. Screen Capture Select Confirm. xxxxx xxxxx xxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxx Figure 32 25/26 NTB19-064c 55. Close C-III plus. 56. Turn the ignition OFF. 57. Disconnect the plus VI from the vehicle. 58. Test drive the vehicle and make sure it operates correctly and the related warning lights are OFF. If any related warning lights come ON, go back to ASIST for further diagnostic information. Diagnosis and repairs beyond ICC/ADAS or LASER/RADAR reprogramming or replacement are not covered by this campaign bulletin. CLAIMS INFORMATION Submit a campaign (CM) type line claim using the following claims coding: CAMPAIGN (“CM”) ID DESCRIPTION OP CODE FRT Reprogram Laser/Radar Control Unit AND ICC/ADAS Control Unit P93270 0.7 hrs. Reprogram ICC/ADAS Control Unit P93271 0.4 hrs. Reprogram Laser/Radar Control Unit P93272 0.4 hrs. Reprogramming not needed P93275 0.3 hrs. P9327 AMENDMENT HISTORY PUBLISHED DATE REFERENCE DESCRIPTION August 26, 2019 NTB19-064 Original bulletin published September 5, 2019 NTB19-064a Part Numbers added to pages 2 and 9 September 20, 2019 NTB19-064b CLAIMS INFORMATION section revised February 2, 2021 NTB19-064c Classification number updated 26/26 NTB19-064c