SA-034-21
Service Bulletin Details
Public Details for: SA-034-21
When performing vehicle services such as control unit software update, control unit registration/activation, cmu log data retrieval, etc., always use the dca8000 or gr8 battery charger sst to maintain battery voltage.
- 2021 - 2020 - 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 -
Models from 2021
| 2021 MAZDA CX-3 |
| 2021 MAZDA CX-30 |
| 2021 MAZDA CX-5 |
| 2021 MAZDA CX-9 |
| 2021 MAZDA MAZDA3 |
| 2021 MAZDA MAZDA6 |
| 2021 MAZDA MX-5 |
Models from 2020
| 2020 MAZDA CX-3 |
| 2020 MAZDA CX-30 |
| 2020 MAZDA CX-5 |
| 2020 MAZDA CX-9 |
| 2020 MAZDA MAZDA3 |
| 2020 MAZDA MAZDA6 |
| 2020 MAZDA MX-5 |
Models from 2019
| 2019 MAZDA CX-3 |
| 2019 MAZDA CX-5 |
| 2019 MAZDA CX-9 |
| 2019 MAZDA MAZDA3 |
| 2019 MAZDA MAZDA6 |
| 2019 MAZDA MX-5 |
Models from 2018
| 2018 MAZDA CX-3 |
| 2018 MAZDA CX-5 |
| 2018 MAZDA CX-9 |
| 2018 MAZDA MAZDA3 |
| 2018 MAZDA MAZDA6 |
| 2018 MAZDA MX-5 |
Models from 2017
| 2017 MAZDA CX-3 |
| 2017 MAZDA CX-5 |
| 2017 MAZDA CX-9 |
| 2017 MAZDA MAZDA3 |
| 2017 MAZDA MAZDA6 |
| 2017 MAZDA MX-5 |
Models from 2016
| 2016 MAZDA CX-3 |
| 2016 MAZDA CX-5 |
| 2016 MAZDA CX-9 |
| 2016 MAZDA MAZDA3 |
| 2016 MAZDA MAZDA6 |
| 2016 MAZDA MX-5 |
Models from 2015
| 2015 MAZDA CX-5 |
| 2015 MAZDA MAZDA3 |
| 2015 MAZDA MAZDA6 |
Models from 2014
| 2014 MAZDA CX-5 |
| 2014 MAZDA MAZDA3 |
| 2014 MAZDA MAZDA6 |
Models from 2013
| 2013 MAZDA CX-5 |
BULLETIN NOTES This service alert supersedes the previously issued service alert listed below. The changes are noted in Red text. Previous TSBs: Date(s) Issued: SA-063/20 08/18/20 APPLICABLE MODEL(S)/VINS 2013-2021 CX-5 2016-2021 CX-3 2014-2021 Mazda3 2016-2021 CX-9 2014-2021 Mazda6 2016-2021 MX-5 2020-2021 CX-30 DESCRIPTION When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. DCA8000 Set the DCA8000 to "Reflash" (PCM/module reflash) or "Manual Charge" (all other service). NOTE: For Manual Mode, set Charge Value to "14.50 V" and Time Type to "CONTINUOUS". 1. From the Main Menu, select "Reflash" or "Manual Charge". Page 1 of 4 05/19/2021 01:39 PM tlawrenc 2. For Manual Charge, fill out the Battery Info and then set Charge Limit to Voltage, Charge Value to 14.5 and Time Type to Continuous. GR8 Set the GR8 to "Manual Charge". • Set Voltage to 14.50 V • Set Max Time to "CONTINUOUS" CAUTION: • DO NOT use the "Power Supply Mode." If the "Power Supply Mode" is used and the vehicle battery is low, the GR8 will switch from "Power Supply Mode" to "Diagnostic Mode." Diagnostic Mode 16V charging is too high for a module software update. • If the vehicle battery is low, charge the battery and only perform a module software update when the GR8 is in "Manual Mode" at 14.50 V charging (see table below). Page 2 of 4 05/19/2021 01:39 PM tlawrenc Good No Good Power Supply Mode Manual Mode Diagnostic Mode GR8 Manual Mode Setup 1. From the Main Menu, select "Manual" 2. Select "REGULAR LEAD ACID" 3. Select "LIMIT VOLTAGE" Page 3 of 4 05/19/2021 01:39 PM tlawrenc 4. Use keypad to enter 14.50 Volts 5. Use keypad to select "CONTINUOUS". Page 4 of 4 05/19/2021 01:39 PM tlawrenc