A4222482038689_6

Technical Service Bulletin
42 Rattle noise from the rear suspension
42 22 48 2038689/6 March 16, 2022. Supersedes Technical Service Bulletin Group 42 number 21-46 dated
August 2, 2021 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
All
2015 – 2023
All
Not applicable
Condition
REVISION HISTORY
Revision
Date
Purpose
6
-
Revised header (Added Model Year)
Revised Warranty (Added Warranty Table)
5
08/02/2021
Revised header (Added Model Years)
4
05/13/2020
Revised header (Added Model Years)
Revised Required Parts and Tools (Added Tools table)
Customer states:
• Clunking or rattling noises are heard from the rear suspension area when the vehicle is driven over bumps.
Technical Background
These noises can be caused by an improperly seated rear bump stop (which occurs when the rear bump stop was
not fully inserted into the rear shock absorber mounting during PDI).
A bump stop installation tool (SET900) was developed to aid with the installation of rear bump stops during PDI
(Figure 1). This tool provides the necessary leverage to seat the rear bump stop in the shock absorber mounting.
© 2022 Audi of America, Inc.
Page 1 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 1. The SET900 bump stop installation tool
Tip: One SET900 tool was sent to all Audi dealers in November 2014. Additional tools can be purchased
through the Audi Special Tools and Equipment Program.
Production Solution
Not applicable.
Service
To ensure proper installation of rear bump stops (in
Audi models without air suspension):
1. Clean the top of the rear bump stops and coat with
tire mounting paste.
2. Use the SET900 special tool to fully press the rear
bump stops into the upper shock mounts (Figure 2).
3. The purpose of the tool is to properly seat the rear
bump stops in the rear shock mounts (Figure 3),
which will prevent them from dropping out of the
rear upper shock mounts and causing the noise.
© 2022 Audi of America, Inc.
Page 2 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 2. The SET900 tool being used to install a rear
bump stop.
Figure 3. Comparison between rear bump stop
installation without and with the SET900 tool.
Note:
Always ensure that the dust boot does not get caught on the top of the shock once the vehicle is lowered.
Tip: A video demonstrating the use of this tool is
available at: https://audiexternal.kzoplatform.com:443/swf/player/286 (Figure
4).
See TSB 2039206: 00 Viewing TSB videos for more
information about viewing videos.
Figure 4. QR code for viewing the video with a QR code
reader on phones and tablets. Alternatively, the video
© 2022 Audi of America, Inc.
Page 3 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
can be accessed through computer internet browsers at
the link provided in this bulletin.
4. If the buffer stops were damaged during the vehicle transport, try to shape them correctly by warming them up
slightly. If this is not possible, replace the affected components.
Warranty
Claim Type:
• 110 up to 48 Months/50,000 Miles.
• If the vehicle is outside any warranty, this Technical Service Bulletin is informational
only.
Service Number:
4298
Damage Code:
0020
Labor Operations:
Secure rear axle buffer stop
4298 1399
10 TU
Secure two rear axle buffer stops
4298 1499
20 TU
Replace rear axle buffer stop
4298 5599
90 TU
Replace rear axle buffer stop (Magnetic Ride)
4298 5599
100 TU
Replace two rear axle buffer stops
4298 5699
140 TU
Replace two rear axle buffer stops (Magnetic
4298 5699
160 TU
GFF
No allowance
0 TU
Road test prior to the service procedure
No allowance
0 TU
Road test after the service procedure
0121 0004
10 TU
Ride)
Diagnostic Time:
Claim Comment:
© 2022 Audi of America, Inc.
As per TSB 2038689/6
Page 4 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts, and Screws as needed per the Repair Manual
See ETKA/ELSA
See ETKA
Buffer Stop
01/02
Tool Number
Tool Description
SET900
Bump stop installation tool
Additional Information
The following Technical Service Bulletin(s) will be necessary to complete this procedure:
• TSB 2039206: 00 Viewing TSB videos.
All parts and service references provided in this TSB (2038689) are subject to change and/or removal. Always check
with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair
Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.
©2022 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time
without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be
modified or reposted to other sites without the prior expressed written permission of the publisher.
© 2022 Audi of America, Inc.
Page 5 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.