SA-001-23a

BULLETIN NOTES
This SA supersedes the previously issued Service Alert(s) listed below. The changes are noted in Red.
Previous SAs:
Date(s) Issued:
SA-001/23
01/03/23
SA-041/22
11/22/22, 09/13/22, 08/17/22 and 06/22/22
APPLICABLE MODEL(S)/VINS
2016-2021 Mazda2 (Mexico/Puerto Rico) with VINS lower than 3MDDJ******409029 (produced before July 13, 2021)
2022 Mazda2 (Mexico) with VINS between 3MDDJ******450001 - 452967 (produced from July 20, 2021 to February 3,
2022)
2014-2016 Mazda3
2017-2018 Mazda3 (Japan built) with VINS between JM1BN******100017 - 199538 (produced from June 27, 2016 to
October 31, 2018)
2017-2018 Mazda3 (Mexico built) with VINS between 3MZBN******100013 - 277187 (produced from September 1, 2016
to December 20, 2018)
2016 Mazda6 (equipped with Center Display P/N GRT7-61-1J0 or GRT7-61-1J0A)
2017-2021 Mazda6
2016-2022 CX-3 with VINS lower than JM1DK******604871 (produced before April 28, 2022)
2017-2020 CX-5 (equipped with Center Display P/N K123-61-1J0 or K123-61-1J0A)
2016-2022 MX-5
Page 1 of 27
01/31/2023 08:38 AM cciz
DESCRIPTION
Some customers may complain about infotainment center display:
• Ghost Touch
• DTC B108E:04 may be stored
(Touch screen operates by itself)
• Surface Peeling
• DTC B108E:04 may be stored
• Spider Cracks
• White dots
IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to
repair the infotainment center display screen.
Customers having this concern should have their vehicle repaired using the following repair procedure.
Page 2 of 27
01/31/2023 08:38 AM cciz
REPAIR PROCEDURE
IMPORTANT NOTE: Repair kits will only fix the symptoms shown in the table below.
Index
Symptom
Model
Year
2016-2021
(Mexico/Puerto Rico) with VINS lower than
3MDDJ******409029 (produced before July 13,
2021)
Surface
Ghost Touch
Peeling
DTC B108E:04
DTC B108E:04
may be stored
may be stored
Spider
Cracking
White
dots
Go to 09-003/
23
Go to 09-003/
23
Go to 09003/23
Go to
09-003/
23
Go to SSPB6
Go to Mazda3
Repair
Go to
Mazda3
Repair
N/A
Go to 09-045/
22
Go to 09-045/
22
N/A
N/A
Go to TSB 09021/22
Go toTSB 09021/22
Go toTSB
09-021/22
N/A
2017-2021
with VINS higher than JM1GL******156205
produced after December 29, 2017)
Go to Mazda6
Repair
Go to Mazda6
Repair
Go to
Mazda6
Repair
N/A
CX-3
2016-2022
with VINS lower than JM1DK******604871
(produced before April 28, 2022)
Go to 09-003/
23
Go to 09-003/
23
Go to 09003/23
Go to
09-003/
23
CX-5
2017-2020
with VINs lower than JM3KF******869655
produced before August 25, 2020)
Go to TSB 09003/22
Go to TSB 09003/22
Go to CX-5
Repair
N/A
Go to TSB 09003/23
Go to TSB 09003/23
Go to TSB
09-003/23
Go to
09-003/
23
Mazda2
Mazda3
Mazda3
2022
(Mexico) with VINS between 3MDDJ******450001
- 452967 (produced from July 20, 2021 to
February 3, 2022)
2014-2016
2017-2018
Japan built - with VINS between
JM1BN******100017 - 199538 (produced from
June 27, 2016 to October 31, 2018)
Mexico built - with VINS between
3MZBN******100013 - 277187 (produced from
September 1, 2016 to December 20, 2018)
2016
equipped with Center Display P/N GRT7-61-1J0
or GRT7-61-1J0A
Mazda6
MX-5
2017
with VINS lower than JM1GL******156205
produced on or before December 29, 2017)
2016-2022
Page 3 of 27
01/31/2023 08:38 AM cciz
1. Verify the customer concern.
2. Disassemble the center display and replace the lens (inner part) with a newly established part according to the
following steps:
3. Print the Parts Flash table and provide to the parts counterperson.
NOTE: Wear the rubber gloves to protect the lens, cable and electronic circuit.
Repair parts set:
No.
Description
Qty.
Notes
(1)
Center Display Lens
1
Cushion materials for packa
ging are used to protect the l
ens surface when disassem
bled.
(2)
Rubber gloves
1
Anti-static
NOTE:
• Center display lens is packaged in bubble wrap and cushion material.
• Unwrap the package carefully so the cushion material can be used to protect the lens surface when disassembling
the center display.
• The center display lens is equipped with cables (FPC: Flexible Printed Circuit), so be careful when handling it.
Page 4 of 27
01/31/2023 08:38 AM cciz
(1) Bubble wrap
(2) Cushion material
CENTER DISPLAY DISASSEMBLY:
Remove the center display according to the instructions on MGSS:
• Mazda3 - CENTER DISPLAY REMOVAL/INSTALLATION
• Mazda6 - CENTER DISPLAY REMOVAL/INSTALLATION
• CX-5 - CENTER DISPLAY REMOVAL/INSTALLATION
Page 5 of 27
01/31/2023 08:38 AM cciz
Mazda3 Repair
1. Remove the 4 screws (1), then remove the connectivity master unit (CMU) (2) from the center display (3).
2. Place the cushion sheet (1) that wrapped lens before, on a clean, flat surface.
3. Put on the rubber gloves.
4. Place the center display (2) on the cushion sheet (1) with the display side facing downward.
5. Remove the 4 screws from the center display cover panels.
Page 6 of 27
01/31/2023 08:38 AM cciz
6. Remove the lower cover panel by pulling it up off the bracket, then lift off the back cover panel.
7. Remove the 4 screws from the bracket.
8. Unlock the bracket with a flat head screw driver by carefully prying out and upward on the bracket.
CAUTION: DO NOT pry on the printed circuit board.
Page 7 of 27
01/31/2023 08:38 AM cciz
9. Remove the bracket.
10. Unlock and disconnect the printed wiring harness.
11. Remove the electric circuit board (1) from the display lens (2).
CAUTION: Be very careful handling the electric circuit board as it will be reused.
Page 8 of 27
01/31/2023 08:38 AM cciz
12. Assemble the modified display lens with the removed electric circuit board.
Inside lens surface
Outside lens surface
NOTE 1:
• Peel off the protection film from the inside lens surface when replacing.
• Peel off the protection film on the outside lens surface after installing the center display to the vehicle.
NOT GOOD
OK
NOTE 2: Solidly connect the printed wiring harness to the connector in order to avoid the half insertion of the printed
wiring harness.
13. Install the center display in the reverse order of removal.
NOTE: DO NOT tighten the screws too tightly, but tighten them so that they do not come loose.
14. Verify the repair.
Page 9 of 27
01/31/2023 08:38 AM cciz
Mazda6 Repair
1. Check the Center Display Part Number (1-2).
Is the Part Number GRT7-61-1J0 or GRT7-61-1J0A?
• Yes - Go to next step.
• No - This service information does not apply. Replace the Center Display unit. Go to MGSS CENTER DISPLAY
REMOVAL/INSTALLATION
2. Remove the 4 screws (1), then remove the connectivity master unit (CMU) (2) from the center display (3).
3. Place the cushion sheet (1) that the lens was wrapped on a working table.
4. Put on the rubber gloves.
5. Place the center display (2) on the cushion sheet (1) with the display side facing downward.
Page 10 of 27
01/31/2023 08:38 AM cciz
6. Remove the 4 screws (1) that assemble the center display (2) and the bracket (3), then separate the bracket (3) and
the cover panel (4).
7. Remove the 2 screws (1) on the back of the center display.
Page 11 of 27
01/31/2023 08:38 AM cciz
8. Insert a tip of a flathead screwdriver (3) in the gap (2) between the lens and the rear cover.
Detail of (1)
Page 12 of 27
01/31/2023 08:38 AM cciz
9. Pull up the rear cover with a flathead screwdriver (1) while being careful to not touch the connector, then remove the
rear cover.
CAUTION: Be careful not to damage the circuit board and the connectors when removing the rear cover.
Pull the rear cover outward so that the cover does not touch the connectors.
Center display (joint with rear cover)
Rear cover (joint with center display)
Page 13 of 27
01/31/2023 08:38 AM cciz
10. Remove the 4 screws (circled in yellow).
11. Push the locking tab (2) on the connector (1) to unlock it while pushing the circuit board, then remove the cable (FPC:
Flexible Printed Circuit) (3).
Page 14 of 27
01/31/2023 08:38 AM cciz
NOTE: Pull out the cable by holding both side-edges of it to avoid damaging the cable.
12. Remove the center display from the lens.
13. Replace the lens with a modified one, reusing the center display
Replace the lens with a modified one.
Reuse the center display.
14. Assemble the center display in the reverse order of disassemble.
NOTE:
• DO NOT tighten the screws too tightly, but tighten them so that they do not come loose.
• When attaching the cable to the circuit board, be careful not to engage with the connector half-fit.
15. Install the center display in the reverse order of removal.
16. Verify the repair.
Page 15 of 27
01/31/2023 08:38 AM cciz
CX-5 Repair
1. Check the Center Display Part Number (1-2).
Is the Part Number K123-61-1J0 or K123-61-1J0A?
• Yes - Go to next step.
• No - This service information does not apply. Replace the Center Display unit. Go to MGSS CENTER DISPLAY
REMOVAL/INSTALLATION
2. Remove the 4 four screws (1), then remove the connectivity master unit (CMU) (2) from the center display (3).
3. Place the cushion material (1) that the lens was wrapped in, on a workbench.
4. Put on the rubber gloves.
5. Place the center display (2) on the cushion material (1) with the display side facing downward.
Page 16 of 27
01/31/2023 08:38 AM cciz
6. Remove the 4 screws (1) that assemble the center display (2) and the bracket (3), then separate the bracket (3) and
the cover panel (4).
7. Remove the 2 screws (1) that assemble the center display and the rear cover (2).
Page 17 of 27
01/31/2023 08:38 AM cciz
8. Remove the rear cover according to the following steps.
• There are 3 three fitting sections of the rear cover and the center display.
• The number in the image below is the order in which to unhook the ribs.
Rear cover
Center display
Page 18 of 27
01/31/2023 08:38 AM cciz
a. Unhook rib (1) by inserting the tip of a flathead screwdriver in the gap (2) between the lens and the rear cover
below connectors (4), then unhooking the rib (3).
Rib (3) of the rear cover
Rib (3) of the rear cover
Hook (5) of the center display
Page 19 of 27
01/31/2023 08:38 AM cciz
b. Unhook rib (2) by inserting the tip of a flathead screwdriver in the gap (2) between the lens and the rear cover,
then unhooking the rib.
c. Unhook rib (3) by inserting the tip of a flathead screwdriver in the gap (3) between the lens and the rear cover,
then unhooking the rib.
Page 20 of 27
01/31/2023 08:38 AM cciz
9. Pull up the rear cover (1) carefully so that the rib (3) does not touch the connectors (2), then remove the rear cover.
Rear cover
Center display
Page 21 of 27
01/31/2023 08:38 AM cciz
10. Remove the 4 screws shown below.
Bracket
Center display
11. Remove the cable (FPC: Flexible Printed Circuit) in order (1), (2), (3) as shown in the image below.
NOTE: To unlock the connector, pull up the locking tab while holding the circuit board.
Page 22 of 27
01/31/2023 08:38 AM cciz
ATTENTION: Pull out the cable by holding both side-edges to avoid damaging the cable.
-->
Locked
Unlocked
-->
(1) Cable
(2) Locking tab
12. Remove the center display from the lens.
13. Replace the lens with a modified one, but reuse the center display
Lens
Center display
Page 23 of 27
01/31/2023 08:38 AM cciz
14. Assemble the center display in the reverse order of disassembly.
NOTE:
• When attaching the cable to the circuit board, be sure the connection is secure.
• DO NOT use electric tools to tighten the screws. Overtightening the screws (circled in yellow in the following
figures) may cause uneven
brightness of the display. If uneven brightness occurs, loosen the screws and retighten them to the point to avoid
coming loose.
Example of the uneven brightness:
Page 24 of 27
01/31/2023 08:38 AM cciz
15. Install the center display in the reverse order of removal.
16. Verify the repair.
Page 25 of 27
01/31/2023 08:38 AM cciz
PARTS INFORMATION
Year
Model
Part
Number
Description
Qty.
Note
Verify Vehicle Infotainment Center Display Part
Label
2016-2017
Mazda2
D0YP-611JZ
Center
Display
Lens Kit
1
Kit repairs P/N D09H-61-1J0B or older
2018-2019
Mazda2
DY1P-611JZ
Center
Display
Lens Kit
1
Kit repairs D23N-61-1J0A or older
2019-2021
Mazda2
D2YN-611JZA
Mazda2
Center
Display
Lens Kit
1
Kit repairs P/N D23N-61-1J0B only
2022
2014-2016
Mazda3
BHY1-611JZ
Center
Display
Lens Kit
1
---
2017-2018
Mazda3
B6YA-611JZ
Center
Display
Lens Kit
1
For verhicles equipped with display B61A-61-1J0*
Includes a center display lens and antistatic rubber
gloves
2016
Mazda6
GRY7-611JZ
Center
Display
Lens Kit
1
Kit repairs P/N GRT7-61-1J0 or GRT7-61-1J0A only
Vehicles equipped with center display P/N GML8-611J0
do not apply to this service information.
2017-2021
Mazda6
GRY7-611JZ
Center
Display
Lens Kit
1
---
2016-2017
CX-3
D0YP-611JZ
Center
Display
Lens Kit
1
Kit repairs P/N D09H-61-1J0B or older
2018-2020
CX-3
DY1P-611JZ
Center
Display
Lens Kit
1
Kit repairs D23N-61-1J0A or older
2019-2022
CX-3
D2YN-611JZA
Center
Display
Lens Kit
1
Kit repairs P/N D23N-61-1J0B only
2017-2020
CX-5
K1Y3-611JZ
Center
Display
Lens Kit
1
Kit repairs P/N K123-61-1J0 or K123-61-1J0A only
Vehicles equipped with center display P/N K123-611J0B or later suffix are already modified and do not
Page 26 of 27
01/31/2023 08:38 AM cciz
apply to this service information.
2016-2017
MX-5
D0YP-611JZ
Center
Display
Lens Kit
1
Kit repairs P/N NA1P-61-1J0B or older
2018-2020
MX-5
D1YP-611JZ
Center
Display
Lens Kit
1
Kit repairs P/N ND1F-61-1J0A or older
2020-2022
MX-5
D2YN-611JZA
Center
Display
Lens Kit
1
Kit repairs P/N ND1F-61-1J0B or ND1F-61-1J0C only
Page 27 of 27
01/31/2023 08:38 AM cciz