TIN-23-66-001
Service Bulletin Details
Public Details for: TIN-23-66-001
This is a technical information notice informing dealers and parts managers about possible causes after a customer complains that the engine will not start while using the remote start system.
- 2023 - 2022 - 2021 - 2020 - 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 -
Models from 2023
2023 MITSUBISHI OUTLANDER SPORT |
Models from 2022
2022 MITSUBISHI OUTLANDER SPORT |
Models from 2021
2021 MITSUBISHI OUTLANDER SPORT |
Models from 2014
2014 MITSUBISHI LANCER |
2014 MITSUBISHI LANCER SPORTBACK |
2014 MITSUBISHI OUTLANDER |
2014 MITSUBISHI OUTLANDER SPORT |
Models from 2013
2013 MITSUBISHI LANCER |
2013 MITSUBISHI LANCER SPORTBACK |
2013 MITSUBISHI OUTLANDER |
2013 MITSUBISHI OUTLANDER SPORT |
Models from 2012
2012 MITSUBISHI ECLIPSE |
2012 MITSUBISHI ECLIPSE SPYDER |
2012 MITSUBISHI GALANT |
2012 MITSUBISHI LANCER |
2012 MITSUBISHI LANCER SPORTBACK |
2012 MITSUBISHI OUTLANDER |
2012 MITSUBISHI OUTLANDER SPORT |
Models from 2011
Models from 2010
2010 MITSUBISHI ECLIPSE |
2010 MITSUBISHI ECLIPSE SPYDER |
2010 MITSUBISHI ENDEAVOR |
2010 MITSUBISHI GALANT |
2010 MITSUBISHI LANCER |
2010 MITSUBISHI LANCER SPORTBACK |
2010 MITSUBISHI OUTLANDER |
* * TECHNICAL INFORMATION NOTICE * * DATE: March 7, 2023 TO: Mitsubishi Motors U.S. Service and Parts Managers RE: Remote Engine Start System Inoperative TIN NO.: TIN-23-66-001 AFFECTED VEHICLES (with Remote Engine Start Kits): * MZ360360EX is a midyear replacement of the MZ360271EX remote engine start kit. PURPOSE: To inform service technicians of possible causes after a customer complains that the engine will not start while using the remote start system. Prior to the replacement of any components, please check the Remote Engine Start Kit and Remote FOB as outlined below. 3/6/2023 1 of 2 (5275) POSSIBLE CAUSES: REMOTE ENGINE START KIT • • • • If the vehicle has been parked for more than two weeks the system will be deactivated. To reactivate system, turn the ignition switch to ACC and then back to OFF. If the vehicle is not equipped with F.A.S.T. key, remove the key, wait three seconds or more, and the system will reactivate (see accessory owner’s manual). Check the remote engine start’s two fuses (5A) attached to the accessory remote engine start harness. Replace any blown fuses and recheck system. Perform hardware troubleshooting diagnostics. Please proceed to the proper install kit instructions and refer to TSB (referenced below) as necessary. Full operation and installation instructions can be found on Mitsubishi CAPS. REMOTE FOB TRANSMITTER • • • • A customer may have locked the remote function by inadvertently pressing the remote “F” and “Lock SW (Switch Lock)” buttons at the same time. Check the remote FOB to see if “SW Lock” is illuminated which indicates it is locked. o TO UNLOCK REMOTE: Press the remote “F” function and “Unl ock SW” buttons at the same time until a buzzer sounds. The "SW Lock" is no longer illuminated the remote function is unlocked. If the batteries have been replaced, ensure the batteries are properly set into position. Check to ensure all doors (including hood and rear tailgate) are fully closed and the door latch switches make contact for electrical connection. If any door latch switch is found faulty or is unable to make electrical contact connection, it will affect the remote engine start. A copy of the customer operation instruction manual can be found on Mitsubishi CAPS. For further details, please reference the TSB-11-66-001REV for additional information on diagnosing the remote engine start, install layout, parts, operation, and troubleshooting. 3/6/2023 2 of 2 (5275)