Edition93
Service Bulletin Details
Public Details for: Edition93
Vw elsa newsletter
- 2015 - 2014 - 2012 - 2011 - 2010 -
Models from 2015
Models from 2014
Models from 2012
2012 VOLKSWAGEN TOUAREG |
Models from 2011
2011 VOLKSWAGEN TOUAREG |
Models from 2010
2010 VOLKSWAGEN TOUAREG |
A PDF of this newsletter and previous ones can be found by logging in to ServiceNet and clicking on the Elsa Newsletter section in the Technician References menu. Edition 93: July 7, 2014 Content Elsa Update: 2011– 2014 Jetta/Jetta Hybrid Technical Bulletins Pending Service Solutions Tech Tips Campaigns Updates Suggestions Elsa Update: 2011–2014 Jetta/Jetta Hybrid Instrument Cluster Trim/Left and Center Instrument Panel Vent Assembly Removal Procedure To all VW dealer technicians. The removal procedure for Jetta (162) has been updated in the Elsa repair manual. Please review the updated procedure to allow proper removal to avoid damage during disassembly. The updated sections are as follows: Body Interior/70 Interior Trim/Removal/instrument panel/Instrument cluster trim, Left and center instrument panel vents Heating Ventilation/80 Heating Ventilation / Removal/Left and center instrument panel vents Back to top Technical Bulletins 00 14 06 - 2015780 Supersedes T. B. V001206 dated November 2, 2012 to include additional models, model year applicability and example pictures of trapped moisture under RAPGARD®. Model(s) Year Eng. Code Trans. Code VIN Range From VIN Range To All Models (except Routan) 2011– 2015 All All All All PDI - Vehicle Inspection, Protection Removal and Detailing Production Solution: Not applicable. 17 14 02 - 2037201 Engine Oil Level Model(s) Year All 2014–2015 Eng. Code Trans. Code All All VIN Range From VIN Range To All All Technicians may find during PDI that the oil level is below the full mark, but still within the hash marks on the engine oil dip stick. Production Solution: Not applicable. Pending Service Solutions No new Pending Service Solutions this week. Back to top Tech Tips 20-12-02 Evap Tank Leak Test Model(s) Year Eng.Code Trans.Code Touareg 2010–2012 V6 3.6L All It is recommended to perform the EVAP tank leak test on V6 equipped Touareg through Control Module OBD. The test can be selected from the basic settings selection under the ECM address 01. Select “Tank Leak Test” basic setting and then select “Measured Values” so that the readings can be monitored during the test (Figure 2). Select “Tank Leak, Result” and “Tank Leak, Status” from the drop down list and press the “forward” arrow to continue. Press the “forward” arrow again and then the ‘Start” button. The brake and gas pedal must both be depressed in order for the test to begin. (See Tech Tip for images) 63-14-01 Paint concerns on front or rear bumper cover Model(s) Year Eng.Code Trans.Code Golf/GTI (A7) 2015 All All In case you have a customer or PDI complaint for paint concerns on the front or rear bumper cover, please open a VTA ticket before performing any repairs to the vehicle. (See Tech Tip for examples) Note: Please open a VTA ticket before performing any kind of repairs. 32-14-01 Torque Converter/Flywheel/Flexplate Installation Model(s) Year Eng.Code Trans.Code All (except Routan) 2000–2015 All All Incorrect torque converter or flywheel/flexplate installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121). Campaigns No new campaigns this week. Updates No new updates this week. Suggestions Please send comments or suggestions to: [email protected] Back to top © 2014 Volkswagen of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.