Chrysler Sebring 1999

• Recall 84391 [USA]: If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
  Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
  federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.
  this recall only pertains to replacement control arm assemblies and has no relation to any original equipment installed on vehicles manufactured by chrysler llc.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 68293 [USA]: Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
  Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
  qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.
  this recall only pertains to aftermarket ball joints and has no relation to any original equipment installed on vehicles produced by chrysler.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 67073 [USA]: This condition may result in a vehicle fire.
  Import products is recalling 30,351 fuel filters sold to and branded by the affinia group as carquest p/n 86523, napa p/n 3523, and wix p/n 33523 for use as replacement equipment on the vehicles listed above. These filters may develop a leak in the hose assembly and/or connectors due to improperly adhered line connectors.
  the affinia group will notify owners and the filters will be replaced free of charge. The safety recall began on august 1, 2009. Owners may contact wix filter return center at 1-704-869-7411 or import products at 1-508-279-8207.
  this recall only pertains to affinia group aftermarket fuel filters and has no relation to any original equipment installed on the listed passenger vehicles.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 83156 [USA]: Decreased lighting visibility may result in a vehicle crash.
  Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." these lamps do not contain the required amber side reflectors.
  sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on may 11, 2009. Owners may contact sabersport at 1-909-598-7589.
  this recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by sabersport.The list can be found under "document search" located at the bottom of your screen.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 88291 [USA]: In the presence of an ignition source, a fuel leak could result in a fire.
  Certain airtex fuel pump module assemblies, p/n e7081h, sold for use as replacement equipment for the vehicles listed above. The wall of the flared fitting of the fuel pump is not thick enough to prevent the mating threaded fittings from bottoming out before an adequate seal is achieved. This condition may result in leakage of fuel at the connection of the vehicle fuel line and the fuel pump module assembly.
  airtex will notify owners and replace the fuel pumps free of charge. The recall is expected to begin during july 2007. Owners can contact airtex automotive at 800-880-3056.
  airtex recall no. FP072007-1.This recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles manufactured by daimlerchrysler or mitsubishi.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 46584 [USA]: Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
  Certain airtex fuel pump modules, p/nos. E7089m, e7094m, e7113m, and e7129m, manufactured between june 1 and september 24, 2006. These fuel pump modules were sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
  airtex will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 18, 2006. Owners may contact airtex toll-free at 1-866-867-3759.
  this recall only pertains to aftermarket fuel pump modules and has no relation to any original equipment installed on vehicles by daimlerchrysler.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 38047 [USA]: Lack of amber side reflectors in the lamps will decrease lighting visibility to other drivers and may possibly result in a vehicle crash.
  Certain tradesonic combination lamps sold as replacement lamps for use on the above listed passenger vehicles. Combination lamps not equipped with amber side reflectors fail to conform with the requirements of federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment.
  tradesonic will notify owners and replace the lamps free of charge. The recall is expected to begin during july 2006. Owners may contact tradesonic at 626-934-8884.
  this recall only pertains to tradesonic aftermarket lamps and has no relation to any original equipment installed on the listed passenger vehicles.For more information on the lamp model numbers, click on document search and view document titled "lamp model numbers."customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 41987 [USA]: Either circumstance may result in the vehicle rolling away without warning.
  On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
  dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1-800-853-1403.
  daimlerchrysler recall no. C45.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 4295 [USA]: This could interfere with the steering control of the vehicle.
  This is not a safety recall in accordance with the safety act. However, it is deemed a safety improvement campaign by the agency. Vehicle description: 1998-1999 chrysler sebring jxi limited convertibles. The steering column intermediate shaft coupler pinch bolt retaining pin could snag and/or fray the edge of the driver's side floor mat.
  dealer will replace the steering column intermediate shaft coupler pinch bolt and retaining pin. In addition, the front floor mats will be replaced.
  daimlerchrysler has decided to conduct a customer satisfaction campaign to replace the steering column intermediate shaft coupler pinch bolt,retaining pin, e-clip and the front floor mats.Owners can contact daimlerchrysler at 1-800-853-1403, concerning this program.

  Show Content

• Recall 3424 [USA]: This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash. this campaign supercedes mmc's previous safety recall campaign, see 99v-066.
  Vehicle description: passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water can intrude. Also, mmc has added the potential of leaking moisture, which can cause the ball stud to corrode.
  dealers will inspect the lower lateral arm ball joint for wear. Ball joints that exhibit wear beyond the established tolerance will be replaced with newly designed lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent intrusion of moisture.
  owner notification began may 21, 2001.Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 8022 [USA]: If the cover separates while driving, it could distract the driver increasing the risk of a crash.
  This is not a safety recall in accordance with the safety act. However, it is deemed a safety improvement campaign by the agency. Vehicle description: passenger vehicles. If the convertible top cover is not installed correctly, it can separate unexpectedly from the vehicle while driving.
  owners will receive an improved convertible top cover instruction label and installation instructions.
  daimlerchrysler has decided to conduct a customer satisfaction notification to send instruction labels to owners.Owners can contact daimlerchrysler at 1-800-992-1997.

  Show Content

• Recall 2001062 [Canada]: Steering
  On certain vehicles, the lower lateral arm ball joint can separate due to loss of lubrication. There is a potential for moisture to leak past the protective boot which can cause the ball stud to corrode. This corrosion, acting much like contamination, can also lead to premature wear and separation of the ball joint. This could result in loss of vehicle control and a possible crash. Correction: lower lateral arm ball joints will be inspected for wear and replaced as necessary with newly designed lower lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent the intrusion of moisture.

  Show Content

• Recall 2004003 [Canada]: Other
  On certain vehicles equipped with an automatic transmission and a floor-mounted shifter, the ignition-park interlock may become defeated and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position. This may result in the vehicle rolling away without warning. Correction: dealer will inspect the function of the ignition-park interlock system. Vehicles found with functional interlock systems will have a load-limiting push rod installed into the floor shifter lever. Vehicles with a non-functional ignition-park interlock system will have the shifter assembly replaced.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

The following is a list of any known keyfobs for the Chrysler Sebring 1999 as well as their FCC IDs if available

• OR-MOP016: 1997-2001 Chrysler Sebring Convertible / 4-Button Keyless Entry Remote / PN: 4671226 / KYPTX002 (OEM Refurb)
  FCC ID: KYPTX002

• Auto trans ignition-park interlock investigation # EA03011

  The manufacturer reports above are based on daimlerchrysler¿s (dc) analysis of model year (my) 1998 (population = 356,384) and 1999 (population = 486,948) ja, jx and lh family subject vehicle data (earlier mys excluded).The population number includes all mys.The precise number of duplicates between odi and dc reports cannot be determined due to missing or incomplete information.The fatality incident involved an elderly person who attempted to stop a roll away vehicle and received fatal injuries.Odi also gathered information on my 1997-99 prowler vehicles in this investigation. The prowler vehicles were manufactured with a different design shifter mechanism (the shift lever is shorter).There are no complaints of prowler interlock failure in odi¿s database, and dc has received no reports either.The prowler is excluded from the recall scope.The investigation involved a condition where the interlock system could fail (or be made inoperative by the operator) during vehicle use, possibly inadvertently.The interlock system is required under fmvss 114.With the transmission in the park position and the ignition key off, the combined action of pressing the shift button and pulling the shift lever rearward may result in the operator overcoming the interlock system and cause the mechanical linkage of the system to disconnect.When this occurs, there is no overt indication to an operator that the system is defeated, and an increased risk of vehicle roll-away exists.Under recall 04v021, dc will replace damaged shift mechanisms, and will install on all vehicles a device which inhibits the operator¿s ability to overcome the interlock and defeat the system.Beginning with my 2000, dc incorporated a brake and transmission shifter interlock (btsi) system into the subject vehicles.Introduction of btsi involved design changes to the shift mechanism, one of which resulted in reduced mechanical advantage (rma) of the shift button.The rma shifter requires increased forces to overcome the interlock system, making the shifter less susceptible to damage.
  

  Show Content

• Safety belt cinching latch plate investigation # PE02082

  There are no injuries or fatalities associated with this alleged defect.While conducting this investigation, odi found that the subject cinches meet the load bearing requirements of federal motor vehicle safety standard 208, and that many of the reported failures were due to incorrect child safety seat installations. Additionally, the report rate is low (1.60/100k).The information available fails to establish the existence of a defect trend at this time.Further allocation of agency resources to this issue is unwarranted and the preliminary evaluation is being closed.
  

  Show Content

• Door panel/garnish separation investigation # PE00007

  Alleged that the plastic garnish panels mounted on doors detach from their mountings, sometimes while the vehicle is in motion
  

  Show Content

Takata recall. I am having several issues with the whole braking system, as it is very difficult to pinpoint the exact cause of having no brakes. I have no type of brakes at all. When taken off parking, even with foot on brake, car will begin to move. This seems to be very common in these cars. The fuel pump was also replaced as it was letting less power go through. This happens as the car sits in parking, as well as, when driving. Also, the mechanic that looked at the car said that the pump needed to be replaced due to possible fire hazards. The lights flicker on and off by themselves, sometimes radio works, sometimes, lights get stuck on.

Driving down road, around 10 miles a hour, the car suddenly went clunk on the left side, and would not move. Got out to check, and the entire piece that holds the tire on was laying on the interior of the tire rim.

Tl* the contact owns a 1999 chrysler sebring convertible. While driving 10 mph, the vehicle stalled and the check engine warning indicator illuminated. The contact stated that the vehicle restarted and the failure recurred. The vehicle was taken to the local dealer (chrysler jeep dodge ram 24, 1020 belmont st, brockton, ma, 02301) where it was diagnosed that there was a fracture in the camshaft timing and that the transmission failed. The vehicle was not repaired. The dealer stated that it was a safety hazard to work on the vehicle due to its condition. The vehicle could not be repaired. The manufacturer was not contacted. The failure mileage was approximately 170,000.

Car shakes at 75 miles per hour..From the front end.

Tl* the contact owns a 1999 chrysler sebring. Prior to purchasing the vehicle, the contact was not informed by the dealer that the vehicle needed extensive repairs. The contact requested reimursement. The manufacturer was not notified. The failure mileage was 200,000.

Takata recall my concerns of accidental discharge,the dash light stays on longer than should.

Car will stall at any speed. Will restart after about 15 tries. Happens after filling tank. 1st thought it was bad gas. But tried different stations. Same problem. Sporadic. Often happens when i shut off car and then attempt to start it again a few minutes later. Doesn't seem to be a problem when the car is cold. Very dangerous situation on high speed roadways. *tr

Tl* the contact owns a 1999 chrysler sebring convertible. While driving approximately 15 mph, the front end of the vehicle collapsed to the ground. The vehicle was towed to an independent mechanic. The technician diagnosed that the front driver's side lower ball joint and axle fractured. The vehicle was not repaired. There was a recall under nhtsa campaign number: 09e056000 (suspension) however, the recall expired. The manufacturer was not notified of the issue. The approximate failure mileage was 129,000. The vin was unavailable. Updated 10/3/2017*cn

Tl* the contact owns a 1999 chrysler sebring. While driving in reverse, the vehicle suddenly accelerated to an extremely high speed. The contact crashed the vehicle into the passenger side of another vehicle. A police report was not filed and there were no injuries. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The speed was unknown. The failure mileage was 155,000.

Common OBD-II Error Codes

• P0720 [1] Output Speed Sensor Circuit Malfunction
• P361A [1] P361A
• B0000 [1] ISO/SAE Reserved
• P0442 [2] Evaporative Emission Control System Leak Detected (small leak)
• P0455 [2] Evaporative Emission Control System Leak Detected (gross leak)
• P0456 [2] Evaporative Emissions System Small Leak Detected
• P1494 [1] EGRCHK Solenoid Circuit Malfunction