Chrysler Sebring 2000

• Recall 84392 [USA]: If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
  Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
  federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.
  this recall only pertains to replacement control arm assemblies and has no relation to any original equipment installed on vehicles manufactured by chrysler llc.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 68294 [USA]: Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
  Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
  qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.
  this recall only pertains to aftermarket ball joints and has no relation to any original equipment installed on vehicles produced by chrysler.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 67072 [USA]: This condition may result in a vehicle fire.
  Import products is recalling 30,351 fuel filters sold to and branded by the affinia group as carquest p/n 86523, napa p/n 3523, and wix p/n 33523 for use as replacement equipment on the vehicles listed above. These filters may develop a leak in the hose assembly and/or connectors due to improperly adhered line connectors.
  the affinia group will notify owners and the filters will be replaced free of charge. The safety recall began on august 1, 2009. Owners may contact wix filter return center at 1-704-869-7411 or import products at 1-508-279-8207.
  this recall only pertains to affinia group aftermarket fuel filters and has no relation to any original equipment installed on the listed passenger vehicles.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 83137 [USA]: Decreased lighting visibility may result in a vehicle crash.
  Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." these lamps do not contain the required amber side reflectors.
  sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on may 11, 2009. Owners may contact sabersport at 1-909-598-7589.
  this recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by sabersport.The list can be found under "document search" located at the bottom of your screen.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 88288 [USA]: In the presence of an ignition source, a fuel leak could result in a fire.
  Certain airtex fuel pump module assemblies, p/n e7081h, sold for use as replacement equipment for the vehicles listed above. The wall of the flared fitting of the fuel pump is not thick enough to prevent the mating threaded fittings from bottoming out before an adequate seal is achieved. This condition may result in leakage of fuel at the connection of the vehicle fuel line and the fuel pump module assembly.
  airtex will notify owners and replace the fuel pumps free of charge. The recall is expected to begin during july 2007. Owners can contact airtex automotive at 800-880-3056.
  airtex recall no. FP072007-1.This recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles manufactured by daimlerchrysler or mitsubishi.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 37152 [USA]: Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
  Certain tigas fuel pump modules manufactured between june 1 and september 24, 2006, sold under various brand names and p/nos. These fuel pump modules are sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
  ti automotive will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 6, 2006. Owners may contact ti automotive toll-free at 1-877-461-1834.
  this recall only pertains to aftermarket fuel pump modules and has no relation to any original equipment installed on vehicles by daimlerchrysler.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 38044 [USA]: Lack of amber side reflectors in the lamps will decrease lighting visibility to other drivers and may possibly result in a vehicle crash.
  Certain tradesonic combination lamps sold as replacement lamps for use on the above listed passenger vehicles. Combination lamps not equipped with amber side reflectors fail to conform with the requirements of federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment.
  tradesonic will notify owners and replace the lamps free of charge. The recall is expected to begin during july 2006. Owners may contact tradesonic at 626-934-8884.
  this recall only pertains to tradesonic aftermarket lamps and has no relation to any original equipment installed on the listed passenger vehicles.For more information on the lamp model numbers, click on document search and view document titled "lamp model numbers."customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 3422 [USA]: This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash. this campaign supercedes mmc's previous safety recall campaign, see 99v-066.
  Vehicle description: passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water can intrude. Also, mmc has added the potential of leaking moisture, which can cause the ball stud to corrode.
  dealers will inspect the lower lateral arm ball joint for wear. Ball joints that exhibit wear beyond the established tolerance will be replaced with newly designed lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent intrusion of moisture.
  owner notification began may 21, 2001.Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 2001062 [Canada]: Steering
  On certain vehicles, the lower lateral arm ball joint can separate due to loss of lubrication. There is a potential for moisture to leak past the protective boot which can cause the ball stud to corrode. This corrosion, acting much like contamination, can also lead to premature wear and separation of the ball joint. This could result in loss of vehicle control and a possible crash. Correction: lower lateral arm ball joints will be inspected for wear and replaced as necessary with newly designed lower lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent the intrusion of moisture.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

The following is a list of any known keyfobs for the Chrysler Sebring 2000 as well as their FCC IDs if available

• OR-MOP016: 1997-2001 Chrysler Sebring Convertible / 4-Button Keyless Entry Remote / PN: 4671226 / KYPTX002 (OEM Refurb)
  FCC ID: KYPTX002

• Safety belt cinching latch plate investigation # PE02082

  There are no injuries or fatalities associated with this alleged defect.While conducting this investigation, odi found that the subject cinches meet the load bearing requirements of federal motor vehicle safety standard 208, and that many of the reported failures were due to incorrect child safety seat installations. Additionally, the report rate is low (1.60/100k).The information available fails to establish the existence of a defect trend at this time.Further allocation of agency resources to this issue is unwarranted and the preliminary evaluation is being closed.
  

  Show Content

I was not informed of a recall and me and my son were in the vehicle driving and it started hopping almost as if it had hydraulic. I told my son to fasten his seat belt considering we were just leaving the store and pulling onto a busy highway. It continued to wobble and i sped up to get off the hwy and then hen the jumping real high and hard began i was going maybe 45 mph and the axle or ballpoint had snapped causing the car wheel to lock up and cause me to run in the ditch luckily no one was harmed but we were very interested much so shaken up.. I had no issue out of that tire or ball joint before and i am needing to know what i need to do to start my investigation... Me and my son are happy no one was injured too bad. *tr

I was not informed of a recall and me and my son were in the vehicle driving and it started hopping almost as if it had hydraulic. I told my son to fasten his seat belt considering we were just leaving the store and pulling onto a busy highway. It continued to wobble and i sped up to get off the hwy and then hen the jumping real high and hard began i was going maybe 45 mph and the axle or ballpoint had snapped causing the car wheel to lock up and cause me to run in the ditch luckily no one was harmed but we were very interested much so shaken up.. I had no issue out of that tire or ball joint before and i am needing to know what i need to do to start my investigation... Me and my son are happy no one was injured too bad. *tr

At approximately 20 mph on a quite neighborhood street both air bags went off with no accident, big bumps or dips or any other reason. I have photos but do not know how to up load them. *dsy.

Seatbelt locks up to where u can't put it on before driving or when driving and seatbelt is on it sometimes locks up and you can't move your locked in place while driving. While driving if it locks up it can happen anywhere on any road or freeway it's malfunctioning and it's annoying especially when u have to be somewhere and you can't get your seatbelt to work making me drive without it on.. Since i bought the car 4 years ago it's been doing this

Seatbelt locks up to where u can't put it on before driving or when driving and seatbelt is on it sometimes locks up and you can't move your locked in place while driving. While driving if it locks up it can happen anywhere on any road or freeway it's malfunctioning and it's annoying especially when u have to be somewhere and you can't get your seatbelt to work making me drive without it on.. Since i bought the car 4 years ago it's been doing this

Tl* the contact owns a 2000 chrysler sebring convertible. While pulling out of a car wash, the vehicle was shifted into drive with the brake pedal depressed. The vehicle suddenly accelerated without warning. The vehicle was towed to a tow lot were it was awaiting inspection. A police report was filed. The manufacturer was not made aware of the failure. The failure mileage was 60,000. Updated 05/16/17*lj *cn

Tl* the contact owns a 2000 chrysler sebring convertible. The contact stated that the wiring harness caught fire. The contact stated that the rain extinguished the fire. A fire report was not filed. A police report was filed. The vehicle was not occupied. The vehicle was not diagnosed nor repaired. The manufacturer was not notified. The failure mileage was approximately 80,000.

Drivers inboard seat belt broke off when my son tried to buckle up in the driveway. Potentially a fatal situation in an accident. The connecting cable frayed. It would not have held in any type of forward accident.

Ii took my car in to have the tires rotated and i was told i need new tires. My tires have only 20k miles and a 60k mile warranty. The tire shop called falken was given the run around for over a week by the manufacturer. I consulted online forums and checked w/ several tire shops and was told that the falken ziex 912's had wear problems and that falken had cut the warranty to 40k miles and they wouldn't sell them. Consumer reports highly recommended them in 2010 which is why i bought them. Many people online only had them last a few months and one lady i recall 6 months and all got no held or relief from falken. Why weren't these recalled and pulled from sale? Falken told the dealer i would need to buy new tires and then they'd consider maybe reimbursing me a small amount. I am disabled on a fixed income and cannot do this and i do not trust falken or their brand. I need tires for my car now and don't know what to do.

Common OBD-II Error Codes

• P0720 [1] Output Speed Sensor Circuit Malfunction
• P361A [1] P361A
• B0000 [1] ISO/SAE Reserved
• P0442 [1] Evaporative Emission Control System Leak Detected (small leak)
• P0455 [1] Evaporative Emission Control System Leak Detected (gross leak)
• P0456 [1] Evaporative Emissions System Small Leak Detected
• P1494 [1] EGRCHK Solenoid Circuit Malfunction