Hino Nv8j 2014

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2014 HINO NV8J.

Manufacturer	Known WMI(s)	Fuel Type
HINO

HINO VIN Decoder

Use the box here to look up VINs from HINO as well as other manufacturers

NHTSA Mandated Recalls

Recall 2016421 [Canada]: Brakes

Recall 2016397 [Canada]: Brakes

Recall 2013464 [Canada]: Steering

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Recalls are also available on the Complaints page

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

TT-14-033 - ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION: When replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
TT-14-017 - EQUIPMENT: Bendix air dryer service
TT-14-016 - EQUIPMENT ADAPTIVE/MOBILITY: Exhaust combustion chamber with loose insulation
SB-14-020 - EQUIPMENT ADAPTIVE/MOBILITY: When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
SB-14-014 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not complete.
SB-14-013 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Dpr damage, "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
SB-14-004 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: In the event that a subject vehicle exhibits an illuminated malfunction indicator lamp (mil) and a P026C (abnormal injection quantity) dtc is stored in the engine ecu, enhanced ecu software is available to correct this concern.
14-002 - EQUIPMENT: Coe hybrid safety equipment, tools and practices
TSB-14-025 - EQUIPMENT: Subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes) setting i
SB-15-010 - EQUIPMENT ADAPTIVE/MOBILITY: Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated egr valve h
167-T1406-12 - ENGINE AND ENGINE COOLING: 14-002 electrical issues or false starter engagement due to coolant intrusion into junction box
167-T1603-12 - ELECTRICAL SYSTEM: Tt-16-001
167-T1514-12 - STRUCTURE:BODY: Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
167-T1513-12 - POWER TRAIN: Tt-15-014 the transmission dtc?S P0974 and P0986, may be found on 12my-15my coe models. There could also be a complaint of low power and erratic shifting. These diagnostic codes may be set due to low voltage between the transmission case an
167-T0706-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 07 - 006 voltage drop test
167-B1312-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. All models
167-B1307-12 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL): 13-008 design change of the idler gear case and idler gear bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idle
167-B1626-12 - ELECTRICAL SYSTEM: Sb-16-022 a subject vehicle may experience an external fuel leak from the burner atomization module assembly, specifically the fuel pressure regulator. This repair procedure outlines replacement of the fuel pressure regulator seals while t
167-B1621-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-010 correction of the inspection of the dpr filter.
167-B1619-12 - SERVICE BRAKES, HYDRAULIC: Sb-16-006 some vehicles built before january 2016 and equipped with a leaf spring rear suspension may experience a dislodged or missing spring pad. As an enhancement, the rear axle leaf spring hanger design has been changed to eliminate the
167-B1618-12 - FUEL/PROPULSION SYSTEM (PWS): Addition of detailed explanation of the fuel pipe installation.
167-T1429-12 - ENGINE (PWS): Tt-14-033 when replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have
167-T1416-12 - SERVICE BRAKES, AIR: Tt-14-017 the bendix ad-is (p/n: k154348) air dryer on air brake equipped vehicles contains several serviceable components. This replacement purge valve can eliminate the need to replace the whole air dryer assembly. These serviceable c
167-T1415-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Tt-14-016 during service of the exhaust aftertreatment system, the technician may visually find that the insulation within the outer shell of the combustion chamber is pushing out or loose. In the event that loose insulation is found, it is
167-B1602-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-16-015 enhanced dcu (dosing control unit) software has been released.Illumination of the check engine light. The dcu may falsely detect an issue and record any of the 3 following dtc?S in the dcu. P142A(def pump temperature sensor - out
167-B1601-12 - FUEL SYSTEM, GASOLINE: Sb-16-007 if dtc(diagnostic trouble code) P0611:fuel injector driver charge circuit - circuit low has set in the engine ecu(electronic control unit) and the workshop manual diagnostic procedure has led to ecu replacement, an enhanced engine
167-B1529-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-032 troubleshooting information and inspection procedure of the dtc/P2030 were revised.
167-B1528-12 - EQUIPMENT:ELECTRICAL: Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. This can result in dtc?S (diagnostic trouble codes) P20E8 or P20E9 - def pressure abnormality. An inlet
167-B1527-12 - EQUIPMENT:ELECTRICAL: Sb-15-030 on subject vehicles, the mil (malfunction indicator lamp) may illuminate with dtc (diagnostic trouble code) U02A2 stored in the engine ecu. This may be due to a malfunction of the def (diesel exhaust fluid) tank sensor assembly. P
167-B1523-12 - ENGINE AND ENGINE COOLING: Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
167-B1518-12 - STRUCTURE:BODY: Sb-15-019 reinforcement brackets and fiberglass repair methods have been made available to address hood crack concerns. In the event a subject vehicle experiences cracking of the hood near the hinges, this repair procedure should be used
167-B1515-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE: Sb-15-016 new parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. This bulletin provides instructions for installing longer manifold studs at the #4 cylinder location.
167-B1513-12 - EQUIPMENT: Sb-15-014 correction of workshop manual for 2011my-2014my (addition and correction of burner system)
167-B1511-12 - STEERING: STEERING WHEEL/HANDLE BAR: Sb-15-011 the following tsb (technical service bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
167-B1510-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated e
167-B1504-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc P0421)
167-B1503-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc P2123)
167-B1417-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-004 in the event that a subject vehicle exhibits an illuminated malfunction indicator lamp (mil) and a P026C (abnormal injection quantity) dtc is stored in the engine ecu, enhanced ecu software is available to correct this concern.
167-B1416-12 - FUEL SYSTEM, GASOLINE: Sb-14-013 "dpr damage", "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to red
167-B1415-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?S P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
167-B1414-12 - STRUCTURE:BODY:HOOD: Sb-14-020 when replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
167-B1426-12 - STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS: Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised p
167-B1423-12 - EQUIPMENT:ELECTRICAL: Sb-14-005 2011my-2015my conventional keyless entry programming
167-B1420-12 - EQUIPMENT:ELECTRICAL: Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not
167-B1423-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-005 2011my-2015my conventional keyless entry programming
167-B1420-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not
167-B1403-12 - ELECTRICAL SYSTEM: Sb-14-016 in the event that one of the subject vehicles is driven while the abs warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an abs warning lamp illuminated can lead to ov
167-B1402-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Sb-14-007 procedure for auto regeneration is possible but not manual regeneration.
167-B1401-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-029 correction of workshop manual for 2011 - 2015 my. Troubleshooting information and inspection procedures for the dtc P2201 and P2214 were revised.
167-B1408-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-028 correction of workshop manual for 2011- 2015 my. Troubleshooting information and inspection procedure of the dtc/P207F were revised.
167-B1407-12 - ELECTRICAL SYSTEM: Sb-14-025 subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes)
167-B1408-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-028 correction of workshop manual for 2011- 2015 my. Troubleshooting information and inspection procedure of the dtc/P207F were revised.
167-B1407-12 - ELECTRICAL SYSTEM: Sb-14-025 subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes)
167-R1404-12 - FUEL SYSTEM, DIESEL: Rcb-005-14 when a subject vehicle is operated at low temperatures, the def (diesel exhaust fluid) in the def hose may freeze, which may cause the on-board diagnostic system to work improperly, and may cause the mil (malfunction indicator la
167-R1401-12 - FUEL SYSTEM, DIESEL: Rcb-004-13 when a subject vehicle is operated at low temperatures, the def (diesel exhaust fluid) in the def hose may freeze, which may cause the on-board diagnostic system to work improperly, and may cause the mil (malfunction indicator la
167-T1303-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-003 injection quantity test 11 thru 14my
167-B0803-12 - WHEELS:LUGS/NUTS/BOLTS: Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
167-B0602-12 - ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER: Sb ? 06 - 002 fuel filter usage. This bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
167-B0601-12 - ENGINE AND ENGINE COOLING: Sb ? 06 - 001 design change of engine oil cooler housing. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retentio
167-B0508-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
167-B0506-12 - ENGINE (PWS): Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
167-B0505-12 - EQUIPMENT ADAPTIVE/MOBILITY: Sb ? 05 - 007 design change of water pipe for j08e
167-B0504-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
167-B0503-12 - ENGINE (PWS): Sb ? 05 - 010 correction to workshop manuals for the j08e engine. A) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. C) r
167-B0502-12 - EQUIPMENT: Sb - 05 - 004 speedometer recalibration. This document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. Tire size change, rear carrier ratio change).
167-B0501-12 - ENGINE (PWS): 05 - 011 corrections to workshop manuals for j08 engines. The standard gap between ends of the second piston ring and the oil ring.
167-P1602-12 - ENGINE (PWS): 13-008 injection pump drive case. Please note the following part number changes to the injection pump bearing case. Not replacing the correct replacement parts will result in major engine damage. The hino ordering system has been modified
167-T1701-03 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: Beginning with the 2017 model year, hino changed the standard battery from a group 27 to a group 31. In the event that a group 27 battery must be replaced, it is recommended to use the group 31 as the service replacement for 2014my and newe